Configure the drive behaviour | Schneider Electric Altivar 212

Configuration

Configure the drive behaviour

The drive trips in Err5 [Com RJ45 fault] or Err8 [Network error fault] if the communication was established and the card no longer receives messages from the network.

The response of the drive in the event of a BACnet communication interruption can be configured by the parameter [Com. fault setting] F851.

Access to the parameter

This parameter is accessible in the [COMMUNICATION MENU] COM submenu of [PROGRAMMING MENU] Programming mode.

Description

Parameter	Modbus	Setting		Default	Valid
	address			setting	after

[Com. fault setting] (F851)	2129	0	[Ramp stp (F/Cmod)]	4	Setting
Communication detected fault	16#851	1	[No active]
setting		2	[Ramp stop]
		3	[Freewheel]
		4	[Err5 or Err8]

WARNING

LOSS OF CONTROL

If F851 is set to 1, communication control will be inhibited.

For safety reasons, inhibiting the communication interruption detection should be restricted to the debug phase or to special application.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

WARNING

LOSS OF CONTROL

Know and understand the setting of parameter F851. This parameter controls the behavior of the drive in the event of a network communication loss. If the value of F851 is 0, 1, 2, or 3, the drive will not trip on an Err8.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

S1A53844 01/2011

29

Image 29

Schneider Electric Altivar 212 manual Configure the drive behaviour, Parameter Modbus Setting Default Valid Address, 2129

Contents

Altivar S1A53844 01/2011 Table of Contents Table of Contents Important Information Safety Information At a Glance About the Book Hazard of Electric SHOCK, Explosion or ARC Flash S1A53844 01/2011 Introduction Introduction Topic Hardware setupWhats in this Chapter? RJ45 Pin out of the Open Style Modbus connectorCross section Tightening torque Pin out of the RJ45 Modbus connector Connection via Open Style wiring systemPin Signal Open Style Reference Connection accessories Connection via RJ45 wiring systemConnecting cables RJ45 Reference Protection Against Interference PTC resistor value F646 Description of terminals GND Hardware setup Configuration Access to the parameters Configuration of the communication parametersParameters Modbus Adjustment range Default Valid Address After Parameters Modbus Setting Configuration of the control sourceControl by the Modbus network Communication Parameters Setting Default ValidControl by the terminals, monitoring by the Modbus network Parameters Modbus Setting Default Valid Com channel choice F807 Communication Menu COM submenu Parameters Modbus Setting Default Valid AddressLI R selection F112 LI R selection Remote spd ref 2 F207 Parameters LocationFrequency source VIA VIA Commands CMOd Complete control diagram Configuration Configuration of the indirect blocks Configuration of the communication interruption Parameter Modbus Setting Default Valid Address Configure the drive behaviourCommunication detected fault 16#851 2129 Configuration Modbus services Principle of the Modbus protocol RTU modeSlave Slave j Slave k Slave address Function code Data Function 3, quantity = Modbus functions availableRead one word Status info Read indirect blockFunction 3, quantity = 1 Read indirect block of 2 parameters Write Single Register Function 16 = 16#10, quantity =1 Write multiple registers Speed Setpoint Command word Frequency SetpointWrite indirect block Request 6C 7E Response Read Device Identification 43/14 Exception code Error response Modbus services Parameter list Setting of Max frequency FH Auto ramp AUI Disabled ManualReferring to the Altivar 212 programming manual General List of control parameters Commands from serial communicationSetpoints from serial communication Outputs control from serial communication Status List of monitoring parametersFrequency and speed Current and torque Maintenance Power and energyTrip and alarm codes Values Bit Specifications Remarks CommandsCommand word FA00 Energy reset bit Command word 2 FA20Examples Over-current stall level change bit Speed setpoint FA13 SetpointsFrequency setpoint FA01 Status word FE0I Fd01 Status Setpoint mode status FE46 Command mode status FE45Status word 2 FE42 Fd42 Status word 3 FE49 Fd49 Alarm of run time FE79 Trip and alarm codesAlarm code FC91 Code Value Description Hexadecimal number Decimal number Digital inputs status Fd06, FE06 Monitoring and control of I/O from communicationDigital outputs status Fd07, FE07 Bit Terminal name Function parameter title Analog outputs command FA51 Digital outputs command FA50Damper opening command Analog inputs values FE35, FE36 F580 = 3 Drive model code F805 Model Voltage Power Rating Code FB05 Class FB72bit8Identification ATV212WU15N4C S1A53844 01/2011 Appendix RS485 standard Modbus 2-wire standard schematicSchematic diagram Migration Commissioning Migration ATV21 ATV212For example ATV212Modbus manualENS1A5384401 S1A53844 01/2011