Parameters, Setting Default Valid | Schneider Electric Altivar 212

Configuration

Control by the terminals, monitoring by the Modbus network

The commands and the setpoint come from the terminals.

The Altivar 212 is monitored via the Modbus network.

The LOC/REM key is valid.

Below is the list of parameters that must be configured.

Access to the parameters

Parameters	Location

[Command mode sel] (CMOd)	[PROGRAMMING MENU] Programming mode
[Frequency mode sel] (FMOd)

[Com channel choice] (F807)	[COMMUNICATION MENU] COM submenu of
	[PROGRAMMING MENU] Programming mode.

Description

Parameters

Modbus

Setting

Default

Valid

address

setting

after

[Command mode sel] (CMOd)

3

0 [Logic inputs]

0

Setting

Remote mode start/stop control

16#3

Control terminal logic inputs

[Frequency mode sel] (FMOd)

4

1 [Ref source VIA]

1

Setting

Remote mode primary speed reference source

16#4

The source of the drive’s

speed reference is VIA.

[Com channel choice] (F807)

2055

0 [RJ45] or

1

Setting

Communication channel selection

16#807

1 [Open style]

Bit 15 of

command word FA00

LOC

Commands CMOd

Serial com. command priority bit

Modbus commands

ON

REM

0

Terminals

REM

Commands

Operation panel

1

Operation

OFF

Modbus

2

LOC

panel

commands

Setpoint FMOd

1

VIA

Modbus setpoint

ON

VIB

2

Operation panel

3

Operation

OFF

Modbus

4

setpoint

Communication

Bit 14 of

panel

UP/DOWN

5

command word FA00

F807

Serial com. setpoint priority bit

RJ45 channel: Modbus

0

Network channel:

1

Paremeter F829

REM

LOC

Setpoint

22	S1A53844 01/2011

Image 22

Schneider Electric Altivar 212 manual Control by the terminals, monitoring by the Modbus network, Parameters

Contents

Altivar S1A53844 01/2011 Table of Contents Table of Contents Safety Information Important Information About the Book At a Glance Hazard of Electric SHOCK, Explosion or ARC Flash S1A53844 01/2011 Introduction Introduction Whats in this Chapter? Hardware setupTopic Cross section Pin out of the Open Style Modbus connectorRJ45 Tightening torque Pin Signal Connection via Open Style wiring systemPin out of the RJ45 Modbus connector Open Style Reference Connecting cables Connection via RJ45 wiring systemConnection accessories RJ45 Reference Protection Against Interference Description of terminals PTC resistor value F646 GND Hardware setup Configuration Parameters Modbus Adjustment range Default Valid Address Configuration of the communication parametersAccess to the parameters After Control by the Modbus network Configuration of the control sourceParameters Modbus Setting Communication Control by the terminals, monitoring by the Modbus network Setting Default ValidParameters Parameters Modbus Setting Default Valid LI R selection F112 Parameters Modbus Setting Default Valid AddressCom channel choice F807 Communication Menu COM submenu LI R selection Frequency source Parameters LocationRemote spd ref 2 F207 VIA VIA Complete control diagram Commands CMOd Configuration of the indirect blocks Configuration Configuration of the communication interruption Communication detected fault 16#851 Configure the drive behaviourParameter Modbus Setting Default Valid Address 2129 Configuration Modbus services Slave Slave j Slave k RTU modePrinciple of the Modbus protocol Slave address Function code Data Read one word Modbus functions availableFunction 3, quantity = Function 3, quantity = 1 Read indirect blockStatus info Read indirect block of 2 parameters Write Single Register Write multiple registers Function 16 = 16#10, quantity =1 Write indirect block Command word Frequency SetpointSpeed Setpoint Request 6C 7E Response Read Device Identification 43/14 Error response Exception code Modbus services Parameter list Referring to the Altivar 212 programming manual Auto ramp AUI Disabled ManualSetting of Max frequency FH General Setpoints from serial communication Commands from serial communicationList of control parameters Outputs control from serial communication Frequency and speed List of monitoring parametersStatus Current and torque Trip and alarm codes Power and energyMaintenance Values Command word FA00 CommandsBit Specifications Remarks Examples Command word 2 FA20Energy reset bit Over-current stall level change bit Frequency setpoint FA01 SetpointsSpeed setpoint FA13 Status Status word FE0I Fd01 Status word 2 FE42 Fd42 Command mode status FE45Setpoint mode status FE46 Status word 3 FE49 Fd49 Alarm code FC91 Trip and alarm codesAlarm of run time FE79 Code Value Description Hexadecimal number Decimal number Digital outputs status Fd07, FE07 Monitoring and control of I/O from communicationDigital inputs status Fd06, FE06 Bit Terminal name Function parameter title Damper opening command Digital outputs command FA50Analog outputs command FA51 Analog inputs values FE35, FE36 F580 = 3 Identification Model Voltage Power Rating Code FB05 Class FB72bit8Drive model code F805 ATV212WU15N4C S1A53844 01/2011 Appendix Schematic diagram Modbus 2-wire standard schematicRS485 standard Migration For example Migration ATV21 ATV212Commissioning ATV212Modbus manualENS1A5384401 S1A53844 01/2011