Precautions, Location | Sharp SRT-8960, SRT-8168, SRT-8040 specs

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

PRECAUTIONS

Location

For safe operation and satisfactory performance of your VCR, keep the following in mind when selecting a place for its installation:

œShield it from direct sunlight and keep it away from sources of intense heat.

œAvoid dusty or humid places.

œAvoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes of the VCR. Do not place the unit on a carpet because this will block the ventilation holes.

œInstall the VCR in a horizontal position only.

œAvoid locations subject to strong vibrations.

œAvoid moving the VCR between cold and hot locations (see “Moisture Condensation Problems”, this page).

œDo not place the VCR directly on top of the TV, as this may cause playback or recording problems.

Avoiding Electrical Shock and Fire

œDo not handle the power cord with wet hands.

œDo not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.

œIf any liquid is spilled on the VCR, unplug the power cord immediately and have the unit inspected at a factory-authorized service center.

œDo not place anything directly on top of this VCR.

Moisture Condensation Problems

Cause:

When the VCR is first installed, moved from a cold area to a warm area or placed in a location with high humidity, dew (moisture) may form in the unit. The Dew indicator (À) blinks. If you operate the VCR with dew inside, damage may result.

Prevention:

1Do not operate the VCR for approximately 2 hours.

When the VCR reaches room temperature, the Dew indicator (À) will turn off and the VCR will be ready for operation.

2

English

Image 3

Sharp SRT-8960, SRT-8168 Precautions, Location, Avoiding Electrical Shock and Fire, Moisture Condensation Problems

Contents

SRT-8960 SRT-8168 SRT-8040 For customers in Canada Precautions Avoiding Electrical Shock and Fire PrecautionsMoisture Condensation Problems Location Contents FeaturesAccessory Front Panel Locations of Controls and Indicators Digital Display Locations of Controls and IndicatorsOperation Indicators Operation Mode Indicator With the RS-485/232C interface board B C D Back Panel With the RS-485/232C interface board Connections Power Cord Installation Sub-menus Using the JOG dial and Shuttle ring for settingsON-SCREEN Menu Main Menu ON-SCREEN Menu Setting the Language and Clock Language SettingClock setting Setting the Language and Clock Automatic Daylight Saving Time AdjustmentFactory setting Superimpose Display Selecting the Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Video Cassette Tapes If tape management data is present on the tape Tape ManagementOperation If no tape management data is present on the tape Setting the Tape Management Function Tape ManagementTape Management menu appears Conflict display sample Tape Management Conflict Display Before starting Recording Speed ModeNormal Recording Normal Recording Recording Check Pause/still indicator N flashesNormal Recording Record Pause Setting the clog detection Action to Take when the Video Signal DeterioratesClog Detection Setting when using Autorepeat recording Setting the Mode at the End of the TapeSetting the video input signal Setting when not using Autorepeat recording Repeat indicator lights Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingALARM/SERIES REC SET menu appears Connections to the Alarm in Terminal Alarm RecordingAlarm Recording Reset Function Alarm Recording Counter Display Alarm Scan Alarm Search Program Timer Recording Timer SET menu appears Program Timer Recording To cancel all program timer recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer Recording These portions will not be recorded Recording Using AN External Timer Input Loop recording Series Recording SetupSeries Recording Operation Single Image Recording Single Image Recording Setup Normal Playback Special Playback Shuttle Ring Operation Special Playback DAY/TIME Search Tape CounterDay/Time Search Quick Method Security Lock Setting the 4 digit security lockCancel the 4 digit security lock Security Lock Clock Adjustment Selecting Input and Output TerminalsConnection Eject input Series in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject output Timer OUT terminal Synchronization Control Operator Mode SC will flash on the digital display Setting the Cassette Eject ModeAdministrator/Installer Mode Synchronization Control Setting for RS-485 or RS-232C USE Setting the Address and Data Transfer SpeedSettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Tape END OUT Terminal Timer OUT terminalTape END OUT Terminal Output Setting Output Terminals SW OUT Terminal Output Setting Output TerminalsSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote Jack Remote control setting Maintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Video SpecificationsGeneral Specifications Connectors Specifications Other SpecificationsConnectors When the Terminal SET is set to SET2 Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR Warranty