Sharp SRT-8168, SRT-8960, SRT-8040 Alarm Recording Setting, ALARM/SERIES REC SET menu appears

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

ALARM RECORDING

By connecting the ALARM IN terminal to a normally open door switch, an interphone, etc., a recording can be done only when necessary.

Alarm Recording Setting

Alarm recording is performed when there is an input (trigger) at the ALARM IN terminal.

œMake all necessary connections.

œThe alarm triggers are received while in recording and stop modes.

œFollow the Before starting steps, under “NORMAL RECORDING”.

1Press the MENU button to display the MAIN MENU.

2Turn the JOG dial to select the “5.ALARM/SERIES REC SET” line, then turn the SHUTTLE ring clockwise.

øThe (ALARM/SERIES REC SET) menu appears.

<ALARM/SERIES@REC@SET>

*ALARM@SET

@@MODE@@@@@@@@@@@Y1

@@SPEED@@@@@@@@@@8H

@@DURATION@@@@@@@20S

*1@SHOT@SET

@@FIELD@@@@@@@@@@1

@@INTERVAL@@@@@@@1M

*SERIES@REC@@@@@@N

*TAPE@END@OUT@@@@8:00

3Turn the JOG dial until the “MODE” setting is highlighted, then turn the SHUTTLE ring clockwise.

4Turn the JOG dial to set the desired alarm recording mode, then turn the SHUTTLE ring clockwise.

Y1. . . . . . Alarm recording is done when there is an alarm trigger.

Y2. . . . . . Alarm recording is done only when there is an alarm trigger during duration of programmed timer recording.

Y3. . . . . . Alarm recording is done only if there is an alarm trigger and the VCR is not in programmed timer recording mode.

Y4. . . . . . Alarm recording is done only when there is an alarm trigger during programmed timer recording duration. VCR comes on records only for alarm duration. Timer recording is not possible.

N. . . . . . . Alarm recording is not performed even

if there is an alarm trigger.

5Turn the SHUTTLE ring clockwise.

6Turn the JOG dial to set the desired alarm recording speed, then turn the SHUTTLE ring clockwise.

8H (6H). . . . . . . . . . . . . 8-hour (6-hour) mode recording

24H (18H) . . . . . . . . . . 24-hour (18-hour) mode recording

40H (30H) . . . . . . . . . . 40-hour (30-hour) mode recording

NC . . . . . . . . . . . . . . . . Recording at the speed already set

œIndicated in brackets are the settings for when “TAPE” is set to “T-120” in the (GENERAL SET) menu.

7Turn the SHUTTLE ring clockwise.

8Turn the JOG dial to set the desired alarm recording duration (20S, 40S, 1M, 2M, 3M, 4M, 5M, or CC), then turn the SHUTTLE ring clockwise.

20S-5M. . Recording only for the displayed duration

CC. . . . . Recording as long as the alarm signal is being input (minimum 5 seconds)

9Press the MENU EXIT button.

NOTES:

œDuring alarm recording all buttons are disabled.

œIf “OFF” appears on the digital display, alarm recording is not possible in order to prevent the recorded tape to be recorded over. To cancel the “OFF” display, press the STOP, EJECT or PLAY button or turn the SHUTTLE ring.

œIf an alarm trigger is received while alarm recording is in progress, recording duration for the second alarm will be calculated from that point. The alarm counter will register the alarm, but it will not be found during an alarm scan and alarm search.

œIf there is a power failure during alarm recording, and the power is restored within the recording set duration, alarm recording will continue.

œIf the alarm recording duration is short, the alarms may not be found during an alarm scan or an alarm search. If the alarms are going to be reviewed using alarm scan or alarm search, then in 8-hour mode,

20-second or more recording duration should be used.

œTo do alarm recording during series recording, set “MODE” to “Y1” or “Y3”. Alarm recording will be conducted only if the VCR is recording.

œIf the recording speed mode is “000”, the recording will be in 8-hour mode irrespective of the alarm recording speed mode setting.

24 English