Configuring | Siemens 505-2557 manual

Configuring the	The SIMATIC 505±2557 must be configured for 10 Ohm copper, 100 Ohm
Module	platinum or 120 Ohm nickel RTDs (2, 3 or 4 wire) or millivolt range and
	digital filtering/no filtering mode before wiring the input connectors and
	inserting the module into the I/O base.

	NOTE: As shipped, all input channels are configured 100 Ohm platinum, 3
	wire RTDs, degrees Centigrade and digital filtering enabled.

	Configuring the module is a two step process. Hardware jumpers are
	positioned to provide proper gain and lead wire compensation for either 3
	wire or 4 wire RTDs. DIP switches are provided to inform the
	microprocessor the changes made to the hardware.
	Changing the module input channel configuration involves the following
	steps:
	1.	Selecting temperature or millivolt measurement via DIP switch
	2.	Selecting 3 or 4 wire compensation
	3.	Selecting 100 Ohm platinum, 120 Ohm nickel or 10 Ohm copper input
		mode for each channel
	4.	Selecting standard login mode (16WX) or Advanced Operating Mode
	5.	Selecting digital filtering or no filtering for the module
	6.	Selecting degrees C or F for the module
	7.	Selecting Engr units or SCALE units for module
	8.	Logging the configuration jumper settings for future reference
	Each of these steps is described in the following sections.

SIMATIC 505±2557 Installation and Operation Guide

Installation

2-3

Image 20

Siemens 505-2557 installation and operation guide Configuring

Contents

Simatic Copyright 1998 by Siemens Energy & Automation, Inc Manual Publication History List of Effective Pages Contents Iv Contents List of Figures List of Tables Preface Agency Approvals EuropeanCommunity CE Approval Description 100 Ohm, 10 Ohm, 120 Ohm RTDs, or Millivolt Inputs Operating Modes Word Input to the PLC from the Module RTD Input to Digital Conversion Scale Units Out-of-Range Input SignalsEffect Effect of Voltage Input 10 Ohm Copper Resolution Input Resolution Selecting 2 and 3 Wire or 4 Wire Operation Installing and Configuring the ModuleCalculating the I/O Base Power Budget Installing and Configuring the Module Configuring Millivolt Input Temperature orSelecting Selecting Degrees Celsius orFahrenheit Selecting Data Configuration Jumper Locations Base InsertingModule Into Wiring the Input Connectors Copper Wire Table at 25 Degrees Celsius Press In Wiring Connector Wiring Diagram for 2, 3, or 4 Wire RTD Wiring Diagram for Millivolt Measurements Cable Grounding Example I/O Configuration Chart Advanced Function Programming Advanced Software Functions IntroductionOverview Advanced Jumper Setting the ModuleConfiguration Memory LoggingController I/O Internal Register Structures Input and Output Register OffsetsInput Registers Input Channel Data Input Flag Bits Peak/Valley Hold Input Words Output Data Registers Averaging Inputs Function Enable BitsControl Registers Discrete Handshake Inputs Outputs Data Identification Bits Loading Data into the Simatic 505±2557 Module Data Loading Process Sample Low and High Alarm Setpoints Identifying the Data Being Transferred 11 Enabling the Functions Loaded Loading Programs into the I/O Module 13 Startup Relay Ladder Logic Page When Using Timing Overhead for Functions EnabledTiming Considerations Timing Constraints Default Values Default Function ValuesDefault Function Values for Simatic 505±2557 Additional Information about Each Function Alarm Setpoints DegreesCentigrade or Degrees Fahrenheit Digital Filtering Hold AveragingPeak and Valley Hold Reset Flag Bits Function Precedence Troubleshooting 10 Troubleshooting Flow Diagram Symptom Probable Cause Corrective Action I/O Register Quick Reference 17 I/O Register Quick Reference Or K Memory Configuration Tables Page Addressing Worksheet Items Unique to the Simatic 505±2557 Module 18 Open RTD Status Bits Troubleshooting Specifications Table B-1 Specifications Specifications subject to change without notice Jumper Settings Log Sheet Customer Response Business Reply Mail