Siemens CM150/3, CM220/3, CM300/3, CM400/3, CM550/3, CM750/3 – Dimension

2. Installation

English

CombiDrive ® – Dimension

(Only dimensions of the motor, total dimensions of the gear motor see

MGS-catalog, Impr.-No. 440 637)

qx = Max. dimension; Given either through the inverter or through the fan cowl.

		Motor-type	Motor	Inverter type	Width (b)	Dimension	qx
	phase	Motor-type	output rating	Inverter type	Width (b)	w´	qx
			output rating			w´
		71 K	0,25 kW	PM 25/1	122	182	237
		71 K	0,25 kW	PM 25/1	122	182	237

	single-	71 L	0,37 kW	PM 37/1	122	182	237

		80 K	0,55 kW	PM 55/1	122	193	259,5
		80 K	0,55 kW	PM 55/1	122	193	259,5

		80 L	0,75 kW	PM 75/1	122	193	259,5

		Motor-type	Motor	Inverter type	Width (b)	Dimension	qx
		Motor-type	output rating	Inverter type	Width (b)	w´	qx
			output rating			w´
		71 L	0,37 kW	PM 37/3	122	182	237

		80 K	0,55 kW	PM 55/3	122	193	259,5

	phase	80 L	0,75 kW	PM 75/3	122	193	259,5

		90 K	1,1 kW	PM 110/3	171	201	296
		90 K	1,1 kW	PM 110/3	171	201	296

	three-	90 L	1,5 kW	PM 150/3	171	201	296

		100 K	2,2 kW	PM 220/3	171	234	328,5
		100 K	2,2 kW	PM 220/3	171	234	328,5

		100 L	3,0 kW	PM 300/3	171	234	328,5

		112 K	4,0 kW	PM 400/3	171	248,5	353

		132 K	5,5 kW	PM 550/3	171	264,5	372,5

		132 L	7,5 kW	PM 750/3	171	264,5	372,5

Dimension in mm

Installation notes

The position of the inverter related to the gearbox, see MGS-catalog (Impr.-No. 440 637). The rotation of the terminal box is not possible.

© STÖBER plc 1997

5	05.02.01

Contents

SIEMENS Micromaster integrated Contents Safety Precautions 1. OVERVIEW 2. INSTALLATION 2.1 Wiring Guidelines to Minimise the Effects of EMI On no account must safety regulations be compromised when installing the CombiDrive® 2.2 Mechanical Installation – Dimension 2.3 Electrical Installation IMPORTANT 2.3.1 Mains Cable Connections 2.3.2 Control Cable Connections Page 2.3.3 Block Diagram 3. OPERATING INFORMATION 3.1 General 3.2 Basic Operation 3.3 Operation - External Analogue Control 3.4 Operation - Digital Control 3.5 Stopping the Motor 3.6 If the Motor Does Not Start Up 3.7 Local and Remote Control 3.8.1 General Description 3.8.2 Hardware Setup 3.8.3 Parameter Settings 4. CLEAR TEXT DISPLAY MODULE & SYSTEM PARAMETERS 4.1 Clear Text Display Module (OPm2) 4.2 System Parameters Note: Notes: 0 1 2 WARNING: The motor can automatically run without a potentiometer or voltage source connected between pins 3 and With P023=2, the motor will automatically start when V exceeds 2 V. This equally applies to P045 P050 P050 = 6 or Value Function of P051 to P053 Relay function Active 4 WARNING: Frequent use of long periods of dc injection braking can cause the motor to overheat If DC injection braking is enabled via a digital input then DC current is applied for as long as the If P078 is set too high, overheating of the motor and/or an overcurrent trip (F002) can occur 3 5 6 8 Page Page 002 003 005 IMPORTANT 5. FAULT CODES 6. SPECIFICATIONS WARNING: Options / Accessories Pulse Resistor Braking Unit Option Electro-mechanicalBrake Control Unit Option PROFIBUS Module Option 7. SUPPLEMENTARY INFORMATION 7.1 Application Example Setup procedure for a simple application 7.2USS Status Codes 7.3 Electro-MagneticCompatibility (EMC) Class 2: Filtered Industrial (Class A) Class 3: Filtered - for residential, commercial and light industry (Class B) 7.4 Environmental Aspects Transport and Storage 7.5 User's Parameter Settings 8.1Control box (Steuerbox) for CombiDrive® integrated / connection diagram Function Farben Number Designation 8.2 Clear text Display Module (Opm2) in IP55 housing Page STÖBER ANTRIEBSTECHNIK