Page 2: System status

ACTIVE LINE: Shows the status of 1080/1035 conversion active line.

1080t1080

1080t1035(CROP)

1080t1035(CONV)

1035t1035

1035t1080(PANEL)

1035t1080(CONV): Shows the current conversion status.

-- - - -: Cannot be converted. OFF: No conversion done.

DOWN CONV. OUTPUT: Shows the output status of the down converter.

ACTIVE: Output.

MUTING: No output.

EOS: Appears at the location of the time code for the valid end of the previous recording.

Page 3: Phase (OUTPUT)

HD SDI OUTPUT ADV.: Shows the phase of the main line HD SDI output.

OFF: In phase with reference.

–90H: 90H (HD) advanced with respect to reference. DOWN CONV. OUTPUT ADV.: Shows the phase of the

down converter output.

OFF: In phase with reference.

–2H: 2H (SD) advanced with respect to reference.

Page 4: Phase (AUDIO)

AUDIO PB OUTPUT ADV.: Shows the phase of the audio output signal.

OFF: Output in phase with the video output signal.

–1Frame: Output one frame advanced with respect to the video output signal.

AUDIO INPUT DELAY: Shows the recording phase of the audio input signal.

OFF: Recorded in phase with the video output signal.

+1Frame: Recorded one frame delayed with respect to the video input signal.

AES/EBU & ANA OUTPUT: Shows the phase of the AES/EBU and ANALOG AUDIO outputs.

REF: Output in phase with reference.

FC: In phase with the FC output.

–90H(HD): 90H (HD) advanced with respect to reference.

–2H(SD): 2H (SD) advanced with respect to reference.

Page 5: Phase (TC)

TC INPUT DELAY: Shows the recording phase of the input time code.

OFF: Recorded in phase with the input video signal.

+1Frame: Recorded one frame delayed with respect to the input video signal.

LTC OUTPUT: Shows the phase of the output LTC. LINE: Output in phase with the main line HD SDI

output.

FC: Output in phase with the FC output.

Page 6: Meta Data

The display changes depending on the tape format in use.

•HDCAM-SR

META DATA LINE(REC): Shows the status of the three lines for metadata recording on this unit.

META DATA LINE(OUT): Shows the status of the three lines of main HD SDI output into which metadata is multiplexed.

META DATA LINE(FC): Shows the status of the three lines of output from the optional HKSR-5001 format converter board into which metadata is multiplexed.

META DATA LINE(SD): Shows the status of the three

lines of SD SDI output into which metadata is multiplexed.

•HDCAM

Displays L1/L2/DID/SDID. This combination is counted as 1 packet. Up to 3 packets can be recorded. On the SRW-5500, the system settings related to recording are shown on the left. If data is detected in the input signal, the L1/L2 values are highlighted. The right side shows playback values detected on the tape.

Note

The ACTIVE LINE setting displayed on page 2 can be made in the SYSTEM screen. The phase settings displayed on pages 3 to 5 and the settings relating to META DATA recording displayed on page 6 can be made in the PHASE SET/META DATA menu under the ALT+OTHERS CHECK menu in the MAINTENANCE menu.

For details, refer to the Installation Manual.

bREF SYNC (reference signal) indicators

These indicate the signal selected as the reference signal. If there is no reference signal input to the selected connector, the STOP button flashes.

EXT SD: Lights when “extern SD” is selected by the VTR SETUP menu item 006 “EXTERNAL REFERENCE select”.

EXT HD: Lights when “extern HD” is selected by the VTR SETUP menu item 006 “EXTERNAL REFERENCE select”.

INPUT VIDEO: Lights when “INPUT” is selected by the VTR SETUP menu item 005 “SERVO/AV REFERENCE select”.

cPREREAD indicator Lights up during preread mode.

For more information about PREREAD, see “6-2-2 Animation Editing” on page 127.

Parts of Functions and Locations 2 Chapter

2-1 Control Panel 21