Item number

Item

Setting

Function

304

VAR SPEED RANGE

[-1 to +2]

Specifies the variable tape speed range when the variable

 

FOR

–1.15 to +2.45

speed playback is executed by a remote control unit

 

SYNCHRONIZATION

 

connected to the REMOTE 1-IN(9P) connector.

 

 

 

–1 to +2: –1 to +2 times normal tape speed

 

 

 

–1.15 to +2.45: –1.15 to +2.45 times normal tape speed

 

 

Note

 

 

 

When

an editing control unit such as BVE-9100 is

 

 

connected for DT editing, select “–1.15 to +2.45”.

 

 

 

305

EDIT FIELD select [1F]

Selects the start timing for editing when performing tape

 

2F

editing.

 

1F/2F

1F: Start editing from field 1 and end on field 2.

 

 

2F: Start editing from field 2 and end on field 1.

 

 

1F/2F: Following received timing commands.

 

 

 

 

 

Note

 

 

 

 

 

 

When

the system frequency of this unit is PsF mode, the

 

 

 

 

 

unit always operates with the 1F setting.

 

 

 

 

 

306

SYNCHRONIZE

[accurate]

When this unit is used as a controller for editing control of

 

 

 

 

rough

another VTR connected through a 9-pin remote cable, this

 

 

 

 

off

selects whether or not to carry out phase synchronization

 

 

 

 

 

of the two VTRs, and also the editing accuracy when

 

 

 

 

 

carrying out synchronization.

 

 

 

 

 

accurate: Editing is carried out with an accuracy of ±0

 

 

 

 

 

frames.

 

 

 

 

 

rough: Editing is carried out with an accuracy of ±1 frame.

 

 

 

 

 

off: Synchronization is not carried out.

 

 

 

 

 

311

EDIT PRESET

[normal]

normal: Assigns edit preset command channels 1 to 8, to

 

 

 

REPLACE MODE

parallel

track channels 1 to 8.

 

 

 

SELECT

reverse

parallel: Assigns edit preset command channels 1 to 4, to

 

 

 

 

stereo

channel pairs 1/5 to 4/8.

 

 

 

 

 

reverse: Assigns edit preset command channels 1 to 4 to

 

 

 

 

 

channels 5 to 8, and channels 5 to 8 to channels 1 to 4.

 

 

 

 

 

stereo: Assigns edit preset command channels 1 to 4 to

 

 

 

 

 

track channel pairs 1/2 to 7/8.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

312

ANALOG AUDIO

[no def]

When the edit presets for VTR channels 9 to 12 are

 

 

 

 

 

 

EDIT PRESET

ch1

specified by an editor or remote controller, these are set on

Appendix

Sub items

ch2

ch1: Follows analog channel 1 edit preset.

 

 

 

REPLACE

or off according to the analog audio edit presets.

 

 

 

 

ch1+2

no def: Not set.

 

 

 

 

 

ch2: Follows analog channel 2 edit preset.

 

 

 

ANALOG AUDIO

 

 

 

 

EDIT PRESET

 

ch1+2: Follows the edit preset for analog channel 1 or

 

 

 

REPLACE FOR

 

analog channel 2.

 

 

 

CH9

 

 

 

 

 

 

 

 

 

 

 

 

 

ANALOG AUDIO

 

 

 

 

 

 

EDIT PRESET

 

 

 

 

 

 

REPLACE FOR

 

 

 

 

 

 

CH10

 

 

 

 

 

 

 

 

 

 

 

 

 

ANALOG AUDIO

 

 

 

 

 

 

EDIT PRESET

 

 

 

 

 

 

REPLACE FOR

 

 

 

 

 

 

CH11

 

 

 

 

 

 

 

 

 

 

 

 

 

ANALOG AUDIO

 

 

 

 

 

 

EDIT PRESET

 

 

 

 

 

 

REPLACE FOR

 

 

 

 

 

 

CH12

 

 

 

150 Menu List