Sony HKDV-502 Audio CH3/4, Input Source, Arrange, Output Mixing, Level Meter, Scale, Audio Output

Menu List

Item number	Item	Settable range	Function
812	AUDIO CH3/4	[CH3/CH4 : sw/sw]	Select the input signal for digital audio channels 3 and 4.
	INPUT SOURCE	CH3/CH4 : ch1/sw	CH3/CH4: sw/sw: The signal that is selected by the upper
	ARRANGE	CH3/CH4 : sw/ch2	control panel is input to channels 3 and 4.
		CH3/CH4 : ch1/ch2	CH3/CH4: ch1/sw: The signal to be recorded in channel 1 is
			also recorded in channel 3.
			CH3/CH4: sw/ch2: The signal to be recorded in channel 2 is
			also recorded in channel 4.
			CH3/CH4: ch1/ch2: The signal to be recorded in channel 1
			is recorded in channel 3 while the signal to be recorded
			in channel 2 is recorded in channel 4.

			Note
			The edit preset for channels 3 and 4 is completely
			independent. Even if this item is set to “CH3/CH4 : sw/sw”
			and insert editing is performed with edit preset for channel 1
			only, no signal is recorded in channel 3.
			The recording level is determined, not by the settings for
			channels 3 and 4, but by the level control of the input
			channels used as the source when this setting is CH3/
			CH4:ch1/sw, CH3/CH4:sw/ch2, or CH3/CH4:ch1/ch2.
			The level control for LINE/MONITOR output is independent
			of E-E, CONFI, and PB modes even when this setting is
			CH3/CH4:ch1/sw, CH3/CH4:sw/ch2, or CH3/CH4:ch1/ch2.
813	AUDIO MONITOR	add	Specifies the type of audio mixing to be conducted on the
	OUTPUT MIXING	[rms]	digital audio signal output to the MONITOR OUTPUT
		average	connector.
			add:Simpleaddition
			rms:Multipliedaverage
			average: Simple average

			Note
			When the CUE channel signal is output to the monitor,
			signals are mixed by simple addition.
814	LEVEL METER	[peak 0 dB]	Specifies the mode in which the digital audio level is
	SCALE	reference 0 dB	displayed.
			peak 0 dB: Displays minus audio levels with the maximum
			level set at 0 dB.
			reference 0 dB: Displays plus and minus audio levels with
			the reference level set at 0 dB.
Appendix			level set at 0 dB.
			Note
			The cue channel level is always displayed with the reference
815	AUDIO OUTPUT	0	Sets the output timing for the digital audio playback signal
	PHASE	.	(SDI and AES/EBU only). The 128 setting specifies the
	preset: 128	[128]	referenceposition.
		.	A setting lower than 128 advances the output timing, and a
		255	setting higher than 128 delays the output timing.
			(128 samples, or approx. 2.7 ms, with 1 sample = approx.
			20 µs)
817	AUDIO LEVEL	[0]	Specifies the brightness of the audio level meter.
	METER DIMMER	.	0 is the brightest level.
	CONTROL	7	7 is the darkest level.
819	NON AUDIO	[BURST DATA MODE]	Specifies the format in which non-audio data is recorded.
	MODE select	CONTINUOUS DATA MODE	BURST DATA MODE: Select this setting for recording data
			compressed in units of video frames (e.g., Dolby E).
			CONTINUOUS DATA MODE: Select this setting for
			recordingdatacompressedwithoutanyrelationshipto
			the video frames (e.g., Dolby Digital (AC-3)).

A-40Appendix