Sony HKDV-501A, HKDV-503, HKDV-502 Error Messages and Warning Messages, To clear a warning message

Error Messages and Warning Messages

Warning Messages

When one of the problems described below is detected, a warning mark is displayed in the upper left corner of the display. Operation can continue even when the mark is flashing.

When the mark is flashing, the warning message can be displayed by using the tip of a small pointed object to press the MAINTENANCE switch.

Note

The warning messages can be viewed in any menu except the CUE or SET UP menu.

Only one message will be displayed even if there are multiple messages, but a history of errors is kept in the error log menu.

For more information about warning messages, refer to the Maintenance Manual.

Use the displayed warning information to eliminate the cause of the warning.

For more information about eliminating the cause of warning, refer to the Maintenance Manual.

To automatically display a warning message Whenever a warning occurs, change item 120.WARNING DISPLAY in the VTR SETUP menu to on.

To clear a warning message

To cancel the display of a warning message, refer to “Clearing warning messages” on page A-12.

Warning mark

R O M	CH.COND				D I A G N O S T I C S
V E R
		T C R 0 0 ; 0 0 ; 0 0 ; 0 0
E R R	M A I N T E N A N C E I N F O M A T I O N D I S P L A Y
L O G
	O P E R A T I O N	5 2 9 H O U R S
	D R U M R U N N I N G		3 4 H O U R S[			2 6 H ]
	T A P E T R A V E L		2 0 H O U R S[			1 6 H ]
	T H R E A D I N G	7 8 0 T I M E S[ 4 4 9 H ]
	W A R N I N G			-	0 2
		L O S T	L O C K
O P T I O N		M A I N T E				E X I T
I N F O		E X E C

Warning message

Appendix

01NO EXTERNAL REFERENCE: There is no reference signal on the selected REF INPUT connector. The VTR is using an internal reference signal.

02LOST LOCK: Capstan servo lock was lost during playback, recording, or editing.

03NO EXTERNAL SD REFERENCE ON PD: When item A05. PD EXT SD REF LOCK MODE in the VTR SETUP menu is set to “lock1” or “lock2,” no external SD reference signal is input (only when the HKDV-507D is installed).

04HD & SD REF ASYNCHRONOUS: When item A05. PD EXT SD REF LOCK MODE in the VTR SETUP menu is set to “lock1” or “lock2,” HD reference signal and external SD reference signal are not synchronized (only when the HKDV-507D is installed).

08NO SDI INPUT: A SDI input signal cannot be detected.

09NO SDI AUDIO INPUT: No audio data detected in the SDI input signal.

10VITC NOT READ: VITC cannot be correctly read from the tape.

11AUDIO PLL UNLOCKED: Audio lock generator PLL not locked to the video reference signal.

14NO PB RF SIGNAL: Playback heads cannot correctly read digital data from the tape.

15INCONSISTENT EMPHASIS: Emphasis information on the tape is inconsistent with the system emphasis status.

16INCONSISTENT FORMAT OF META DATA: The meta data being input and the meta data recorded on the tape have different formats.

17PB FREQUENCY IS UNSUITABLE: The cassette is ejected automatically in line with the setting of item 018.AUTO EJECT LEVEL in the VTR SETUP menu because the system frequency of the VTR and the frequency of the signal recorded on the tape do not match.

1C NO A1/A2 INPUT: No carrier detected on digital audio input on channels 1 and 2

20NO A3/A4 INPUT: No carrier detected on digital audio input on channels 3 and 4

2D INVALID SDI DATA: SDI input signal data is invalid.

34NO CASSETTE COMPARTMENT MODE: The cassette compartment does not operate during no cassette compartment mode.

3B NO LTC REPRODUCED: LTC signal not detected on the tape.

45DT UNLOCKED: DT cannot be correctly traced during playback, recording, or editing.

50PROCESSOR IS IN TEST MODE: The processor is in test mode.

55VIDEO PLL UNLOCKED: Video lock generator PLL not locked to the video reference signal.

A-10Appendix