Setting the current tape position as point A or B
POWER |
|
|
|
|
|
|
|
|
|
| EJECT |
|
|
|
|
|
|
|
|
|
|
| LOCAL |
|
|
|
|
|
|
|
|
|
|
| 9PIN |
|
|
|
|
|
|
|
|
|
|
| i.LINK |
i.LINK | INPUT SELECT | CH2 3/4 |
|
|
|
|
|
|
|
| |
VIDEO | CH1 1/2 |
|
|
|
|
|
|
|
| ||
|
|
|
| OVER | OVER | REPEAT | 1080 | 525 |
|
| HDV DVCAM |
|
|
|
|
| 0 |
|
| ||||
| REC/PB LEVEL |
|
|
|
|
|
|
|
| (DV) | |
1 | 4 |
|
|
|
|
|
|
| |||
2 | 3 |
|
|
|
| DISPLAY | MENU | ASSIGN RESET(NO) | |||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| TC |
| |
|
|
| MONITOR | CH1 | CH2 | TC VITC | 44.1K |
| COUNTER | SET(YES) | |
LEVEL | VARIABLE |
| EDIT MODE | 01:23:45:15 | PRESET | ||||||
| SELECT | SELECT |
|
| |||||||
| REC | PRESET |
| REC INHI |
|
|
| ||||
| PB |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
PHONES | REW | PLAY | F FWD | STOP |
| REC | A | B | |||
| MENU ASSIGN RESET(NO) | ||
| TC | SET(YES) | |
3 Chapter | PRESET | ||
|
| ||
Recording | A | B | |
| |||
and | Buttons used for setting | Buttons used for setting | |
| |||
Playback | the current tape position | the current tape position | |
as point A | as point B | ||
| |||
While holding down the SET (YES) button in the menu control section, press the </A or ,/B button. The timecode value of the current tape position is set as point A or B, and a message “A set” or “B set” is displayed for 0.5 second in the time counter display.
Once set, the point A or B timecode value is held in the
Note
When setting point A or B, you can only use a timecode value. Even when CNT is selected with the COUNTER SELECT button, you cannot use a CNT value to set point A or B.
To check the point A or B timecode value
Press the </A or ,/B button in the menu control section. While the button is held down, the point A or B timecode value is displayed on the monitor screen and in the time counter display.
If you hold down the </A and ,/B buttons simultaneously, the value shown is the point B timecode value minus the point A timecode value. If the point A timecode value is greater than the point B timecode value, a minus sign
Inputting timecode values for points A and
B
Using the following procedure, you can modify the timecode value for point A or B.
MENU ASSIGN RESET(NO)
1,15
TC
PRESETSET(YES)
13
12
A | B |
8,11 
2,3,4,6,
10,11
5,7,9,12
1 Press the MENU button.
The following menu display appears.
| SYSTEM MENU |
| Setup menu |
|
|
| |
SETUP | MENU |
| |
|
| ||
AUTO | FUNCTION |
| Time counter display |
HOURS | METER |
|
|
|
|
|
|
Monitor screen
2 With SETUP MENU selected, press the ,/B button.
The display changes as follows.
| SETUP | MENU |
| Operational |
|
|
|
| |
OPERATIONAL | FUNCTION |
| ||
DISPLAY CONTROL |
| Time counter display | ||
TIME | CODE |
|
| |
|
|
| ||
SETUP | BANK | OPERATION |
|
|
SYSTEM SEL | : J |
|
| |
MENU | GRADE | : BASIC |
|
|
|
|
|
|
|
Monitor screen
3 With OPERATIONAL FUNCTION selected, press the ,/B button.
The display changes as follows.
| SETUP | MENU |
| > REP FUNC | |
OPERATIONAL | FUNCTION |
| |||
|
|
|
|
| Time counter display |
REPEAT | FUNCTION |
| |||
AUTO | EE | SELECT |
|
| |
LOCAL ENABLE :STP&EJ |
|
| |||
REC | FORMAT |
|
|
| |
|
|
|
|
|
|
Monitor screen
4 With REPEAT FUNCTION selected, press the ,/B button.
The contents of the REPEAT FUNCTION menu item are displayed.
48 Playback