Alarm message on monitor | Direction | Alarm message in time counter |
screen (Cause) |
| display |
A | Use a standard signal. | REF |
used for REF. VIDEO. |
|
|
|
|
|
Abnormal settings selected in setup | Correct the setup menu settings. Contact your Sony | ILL. SETUP! |
menu. | dealer if this alarm message appears again after |
|
| making corrections. |
|
|
|
|
Audio mixing mode cannot be | − | REC mode! |
changed during recording. |
|
|
|
|
|
Audio not editable on this tape. | Use a tape recorded in | 2CH/32kHz! |
| channel/32 kHz mode. |
|
| Fs 44.1kHz! | |
|
| |
|
|
|
| Use a tape having audio signals recorded in locked | UNLOCK mode |
| mode. |
|
|
|
|
Audio REC mode selection different | Select the same audio recording mode as that of | A mode err |
from audio on tape. | the tape. |
|
|
|
|
Audio REC (recording) mode cannot | − | REC mode! |
be changed during recording. |
|
|
|
|
|
Battery needs to be replaced with a | − | Exchg batt! |
new one. Please contact service |
|
|
personnel. |
|
|
|
|
|
Cassette adaptor not usable. | Use a tape without cassette adaptor. | Adaptor! |
|
|
|
Change the HDV/DV i.LINK input | − | HDV INPUT! or DV INPUT! |
setting. |
|
|
|
|
|
Counter mode is selected. | Use the COUNTER SELECT button to light the TC | CNT mode! |
| or UB time data type indicator in the display section. |
|
|
|
|
Input selection cannot be changed in | − | REC mode! |
REC (recording) mode. |
|
|
|
|
|
Input signal does not conform to | − | Unknown Sig |
DVCAM/DV format. |
|
|
|
|
|
Input signal is 625/50. | − | 625/50 sig! |
|
|
|
Input signal is 525/60. | − | 525/60 sig! |
|
|
|
Input video is not detected. | Check the indicator in the video area in the input | No INPUT! |
| signal display and supply an appropriate video |
|
| signal. |
|
|
|
|
Input video signal does not | Use a reference video signal. | ILL. REF! |
synchronize with REF. VIDEO |
|
|
signal. |
|
|
|
|
|
Moisture has been detected. | Keep the power on and wait until this alarm | HUMID! |
| message disappears. |
|
|
|
|
No cassette in VTR. | Load a cassette. | No Cass.! |
|
|
|
Non DVCAM/DV(SP) format source. | − | No DVCAM/DV |
|
|
|
Rec inhibit mode is selected. | Set the REC INHIBIT menu item (see page 74) to | REC INHI.! |
| OFF. |
|
|
|
|
Record inhibit plug on the cassette is | Set the REC/SAVE switch on the cassette to REC. | REC INHI.! |
set to inhibit. |
|
|
|
|
|
Remote mode is selected. | Set the remote control switch to LOCAL. | REMOTE! |
|
|
|
Select DVCAM recording format. | Set the REC FORMAT menu item (see page 74) to | Not DVCAM! |
| DVCAM. |
|
|
|
|
Tape cannot be replayed. | Use a tape recorded in 525/60 format. | 625/50 Tape |
|
|
|
| Use a tape recorded in 625/50 format. | 525/60 Tape |
|
|
|
Tape end has been detected. | Use a new cleaning tape. | Tape end! |
|
|
|
Appendix
Troubleshooting 97