Appendix D System Speciﬁcations | SUPER MICRO Computer 6025B-3R

Appendix D: System Speciﬁcations

Appendix D

System Speciﬁcations

Processors

Single or dual Intel® quad-core Xeon® 5400/5300 Sequence processors or dual- core Xeon 5000/5100 Sequence processors at a FSB speed of 1333/1066/667 MHz

Note: Please refer to our web site for a complete listing of supported processors.

Chipset

Intel 5000P/ESB2 chipset

BIOS

8 Mb Phoenix® Flash ROM

Memory Capacity

Eight 240-pin DIMM sockets supporting up to 32 GB of FBD ECC DDR2- 667/533 SDRAM

Note: 2-way interleaved memory - requires memory to be installed four modules at a time. See

the memory section in Chapter 5 for details.

SAS Controller

Adaptec 9410 controller for 8-port SAS (RAID 0, 1 and 10 supported)

SAS Drive Bays

Eight (8) hot-swap drive bays to house eight (8) SAS drives

Peripheral Drive Bays

One (1) slim ﬂoppy drive (optional)

One (1) DVD-ROM drive

Expansion Slots

Two PCI-Express x8 slots, one PCI-Express x4 slot, two 64-bit 133 MHz PCI-X slots and one 64-bit 100 MHz PCI-X slot

D-1

Page 123

Image 123

SUPER MICRO Computer 6025B-3R user manual Appendix D System Speciﬁcations

Contents

Super Manual Revision 1.0c Release Date February 5 Preface About This ManualManual Organization Bios System SafetyAdvanced Serverboard Setup Advanced Chassis Setup Preface Table of Contents HDD LED NIC1 LED NIC2 LED Advanced Serverboard Setup Bios Advanced Chassis Setup Appendices Page Overview Chapter Introduction PCI Expansion Slots Serverboard FeaturesProcessors Memory Onboard SAS Other Features Onboard Controllers/PortsATI Graphics Controller Front Control Panel Server Chassis FeaturesSystem Power SAS Subsystem Cooling System Intel 5000P Chipset System Block Diagram Asia-Paciﬁc Contacting SupermicroHeadquarters Europe Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the Chassis Rails Installing the System into a Rack Installing Chassis Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Page Control Panel Buttons Chapter System Interface Control Panel LEDs SAS Drive Carrier LEDs Page Electrical Safety Precautions Chapter System Safety General Safety Precautions ESD Precautions Installing the Onboard Battery Operating Precautions Unpacking Chapter Advanced Serverboard SetupPrecautions Handling the Serverboard Installing the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the Heatsink Connecting Cables Connecting Data CablesConnecting Power Cables Front Control Panel Header Pins JF1 Connecting the Control Panel Installing Memory Dimm Installation See FigureI/O Ports Memory Support 3a. Installing Dimm into Slot PCI Card Installation Adding PCI CardsPCI Expansion Slots Super X7DB3 Layout Serverboard Details Jumper Description Default Setting Connector DescriptionX7DB3 Quick Reference Connector Deﬁnitions Overheat/Fan Fail LED OH HDD LED Universal Serial Bus USB0/1 Power Fail LEDReset Button Power Button Chassis Intrusion Power Fail HeaderSerial Ports Fan Headers Overheat LED Power LED/SpeakerExtra Universal Serial Bus Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Wake-On-Ring Wake-On-LAN Alarm Reset JAR JLAN1/2 Ethernet PortsKeylock Cmos Clear Jumper SettingsVGA Enable/Disable Explanation Jumpers 3rd Power Supply Fail Detect Enable/Disable Jlan Enable/DisableCompact Flash Master Slave Onboard Indicators Watch Dog Enable/DisableJLAN1/JLAN2 LEDs Parallel Printer Port Pin Deﬁnitions Parallel Port Connector Floppy Drive Connector Pin Deﬁnitions J22 Floppy Connector Sata Ports IDE Connectors SB5 SAS PortsPage Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Unpacking Front and Rear Chassis Views Control Panel Replacing System Fans Installing a new fanSystem Fans System Fan Failure Accessing the Drive Bays Drive Bay Installation/Removal Mounting a SAS drive in a drive carrier SAS Drive Installation Removing a SAS Drive Carrier Installing/removing hot-swap SAS drives DVD-ROM Installation Installing Components in the 3.5 Drive Bays 6025B-3 Power SupplyPower Supply Failure Removing/Replacing the Power Supply 6025B-3R Page Chapter System BiosHow To Change the Conﬁguration Data Starting the Setup Utility Running Setup Main Bios SetupPress the Delete key to enter Setup System Date Main Bios Setup Menu Main Setup FeaturesBios Date System Time Type Multi-Sector Transfers LBA Mode ControlTransfer Mode Ultra DMA Mode Parallel ATA Native Mode OperationSata Controller Mode Serial ATA Sata RAID Enable Advanced Setup System MemoryExtended Memory Acpi Mode Boot FeaturesQuick Boot Mode Quiet Boot Cache Base 512K-640K Memory Cache Cache System Bios AreaCache Video Bios Area Cache Base 0-512K PCI Conﬁguration PCI Parity Error ForwardingReset Conﬁguration Data Discrete Mtrr Allocation Serr Signal Condition Enable MasterLatency Timer Large Disk Access Mode Enabling Multi-Media Timer Memory Branch ModeCrystal Beach Features Clock Spectrum Feature CPU Speed Advanced Processor Options Base I/O Address Device ConﬁgurationKBC Clock Input Serial Port a Parallel Port InterruptSerial Port B Mode View DMI Event Log DMI Event LoggingEvent Log Validity Event Log Capacity Console Type Console RedirectionCOM Port Address Baud Rate Fan Speed Control Modes CPU Temperature ThresholdHardware Monitor Logic Voltage Monitoring CPU Temperature Threshold See note on Hardware Monitor Logic See note on Temperature Monitoring Clear System Event Logging Bios Post ErrorsBios Post Watch Dog System Event Logging Time Out Option OS Boot Watch DogTimer for Loading OS Minutes System Event Log/System Event Log List Mode Realtime Sensor Data Set User Password Supervisor Password IsUser Password Is Set Supervisor Password Boot Password on BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages Check date and time settings System Cmos checksum bad Default conﬁguration usedSystem timer error Real time clock error Entering Setup System cache error Cache disabledFail-Safe Timer NMI Failed Allocation Error for device Nnnn kB Extended RAM Passed PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Device IRQ conﬂict Video Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup System Bios shadowedPage Post Code Description Appendix B Bios Post CodesRecoverable Post Errors Terminal Post Errors Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Adaptec SAS HostRAID Appendix C RAID and Software InstallationUsing the Adaptec RAID Conﬁguration Utility ARC Using the Array Conﬁguration Utility ACU Managing Arrays Viewing Array PropertiesFrom the ARC menu, select Array Conﬁguration Utility ACU Creating Arrays Deleting Arrays To assign properties to the new array Assigning Array Properties Ctrl+B Adding a Bootable ArrayDeleting a Bootable Array To make an array bootable To Rebuild an array Initializing Disk DrivesRebuilding Arrays To initialize drives To access the SAS utilities Using the SerialSelect Utility to Conﬁgure SAS Settings To set the controller conﬁguration To Set the Physical Conﬁguration Using the Disk Utilities To access the disk utilitiesFollowing options are available Exiting the Adaptec RAID Conﬁguration Utility Driver/Tool Installation Display Screen Installing Drivers Conﬁguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Appendix D System Speciﬁcations Motherboard WeightPower Supply 6025B-3 Power Supply 6025B-3R Regulatory Compliance Operating Environment