IDE Connectors, Sata Ports | SUPER MICRO Computer 6025B-3R specs

SUPERSERVER 6025B-3/6025B-3R User's Manual

IDE Connectors

IDE Drive Connectors

Pin Deﬁnitions (IDE#1, IDE#2)

There are no jumpers to conﬁg- ure the onboard IDE#1 and #2 connectors. See the table on the right for pin deﬁnitions.

Pin# Deﬁnition

1Reset IDE

3Host Data 7

5Host Data 6

7Host Data 5

9Host Data 4

11Host Data 3

13Host Data 2

15Host Data 1

17Host Data 0

19Ground

21DRQ3

23I/O Write

25I/O Read

27 IOCHRDY

29 DACK3

31 IRQ14

33Addr1

35Addr0

37Chip Select 0

39 Activity

Pin # Deﬁnition

2 Ground

4Host Data 8

6Host Data 9

8Host Data 10

10Host Data 11

12Host Data 12

14Host Data 13

16Host Data 14

18Host Data 15

20Key

22Ground

24Ground

26Ground

28	BALE
30	Ground
32	IOCS16

34Ground

36Addr2

38Chip Select 1

40 Ground

SATA Ports

There are no jumpers to con- ﬁgure the onboard SATA con- nectors. See the table on the right for pin deﬁnitions.

SATA Port Pin Deﬁnitions

(SATA0 - SATA5)

Pin #

Deﬁnition

1Ground

2TXP

3TXN

4Ground

5RXN

6RXP

7Ground

5-24

Image 58

SUPER MICRO Computer 6025B-3R user manual IDE Connectors, Sata Ports

Contents

Super Manual Revision 1.0c Release Date February 5 About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup Bios Preface Table of Contents Advanced Serverboard Setup HDD LED NIC1 LED NIC2 LED Advanced Chassis Setup Bios Appendices Page Chapter Introduction Overview Onboard SAS Serverboard FeaturesProcessors Memory PCI Expansion Slots Onboard Controllers/Ports Other FeaturesATI Graphics Controller SAS Subsystem Server Chassis FeaturesSystem Power Front Control Panel Intel 5000P Chipset System Block Diagram Cooling System Europe Contacting SupermicroHeadquarters Asia-Paciﬁc Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the System into a Rack Installing the Chassis Rails Installing the Server into the Rack Installing Chassis Rails Installing the Server into a Telco Rack Installing the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Page Chapter System Interface Control Panel Buttons Control Panel LEDs SAS Drive Carrier LEDs Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Handling the Serverboard Chapter Advanced Serverboard SetupPrecautions Unpacking Processor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the Heatsink Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1 Dimm Installation See Figure Installing MemoryI/O Ports 3a. Installing Dimm into Slot Memory Support Adding PCI Cards PCI Card InstallationPCI Expansion Slots Serverboard Details Super X7DB3 Layout Connector Description Jumper Description Default SettingX7DB3 Quick Reference Connector Deﬁnitions HDD LED Overheat/Fan Fail LED OH Power Button Power Fail LEDReset Button Universal Serial Bus USB0/1 Fan Headers Power Fail HeaderSerial Ports Chassis Intrusion ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerExtra Universal Serial Bus Headers Overheat LED Wake-On-LAN Wake-On-Ring JLAN1/2 Ethernet Ports Alarm Reset JARKeylock Explanation Jumpers Jumper SettingsVGA Enable/Disable Cmos Clear Jlan Enable/Disable 3rd Power Supply Fail Detect Enable/DisableCompact Flash Master Slave Watch Dog Enable/Disable Onboard IndicatorsJLAN1/JLAN2 LEDs Parallel Port Connector Parallel Printer Port Pin Deﬁnitions Floppy Connector Floppy Drive Connector Pin Deﬁnitions J22 IDE Connectors Sata Ports SAS Ports SB5Page Unpacking Chapter Advanced Chassis SetupStatic-Sensitive Devices Tools Required Control Panel Front and Rear Chassis Views System Fan Failure Installing a new fanSystem Fans Replacing System Fans Drive Bay Installation/Removal Accessing the Drive Bays SAS Drive Installation Mounting a SAS drive in a drive carrier Installing/removing hot-swap SAS drives Removing a SAS Drive Carrier Installing Components in the 3.5 Drive Bays DVD-ROM Installation Removing/Replacing the Power Supply Power SupplyPower Supply Failure 6025B-3 6025B-3R Page Starting the Setup Utility System BiosHow To Change the Conﬁguration Data Chapter Main Bios Setup Running SetupPress the Delete key to enter Setup System Time Main Bios Setup Menu Main Setup FeaturesBios Date System Date Type Ultra DMA Mode LBA Mode ControlTransfer Mode Multi-Sector Transfers Serial ATA Sata RAID Enable Native Mode OperationSata Controller Mode Parallel ATA System Memory Advanced SetupExtended Memory Quiet Boot Boot FeaturesQuick Boot Mode Acpi Mode Cache Base 0-512K Memory Cache Cache System Bios AreaCache Video Bios Area Cache Base 512K-640K Discrete Mtrr Allocation PCI Parity Error ForwardingReset Conﬁguration Data PCI Conﬁguration Large Disk Access Mode Enable MasterLatency Timer Serr Signal Condition Clock Spectrum Feature Memory Branch ModeCrystal Beach Features Enabling Multi-Media Timer Advanced Processor Options CPU Speed Serial Port a Device ConﬁgurationKBC Clock Input Base I/O Address Mode InterruptSerial Port B Parallel Port Event Log Capacity DMI Event LoggingEvent Log Validity View DMI Event Log Baud Rate Console RedirectionCOM Port Address Console Type Voltage Monitoring CPU Temperature ThresholdHardware Monitor Logic Fan Speed Control Modes CPU Temperature Threshold See note on Temperature Monitoring Hardware Monitor Logic See note on System Event Logging Bios Post ErrorsBios Post Watch Dog Clear System Event Logging System Event Log/System Event Log List Mode OS Boot Watch DogTimer for Loading OS Minutes Time Out Option Realtime Sensor Data Set Supervisor Password Supervisor Password IsUser Password Is Set User Password Password on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default conﬁguration usedSystem timer error Check date and time settings Allocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering Setup Device IRQ conﬂict PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Nnnn kB Extended RAM Passed System Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Using the Array Conﬁguration Utility ACU Appendix C RAID and Software InstallationUsing the Adaptec RAID Conﬁguration Utility ARC Adaptec SAS HostRAID Viewing Array Properties Managing ArraysFrom the ARC menu, select Array Conﬁguration Utility ACU Deleting Arrays Creating Arrays Assigning Array Properties To assign properties to the new array To make an array bootable Adding a Bootable ArrayDeleting a Bootable Array Ctrl+B To initialize drives Initializing Disk DrivesRebuilding Arrays To Rebuild an array Using the SerialSelect Utility to Conﬁgure SAS Settings To access the SAS utilities To set the controller conﬁguration To Set the Physical Conﬁguration To access the disk utilities Using the Disk UtilitiesFollowing options are available Exiting the Adaptec RAID Conﬁguration Utility Installing Drivers Driver/Tool Installation Display Screen Conﬁguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Appendix D System Speciﬁcations Power Supply 6025B-3R WeightPower Supply 6025B-3 Motherboard Operating Environment Regulatory Compliance