X7DB3 Quick Reference | SUPER MICRO Computer 6025B-3R manual

Chapter 5: Advanced Serverboard Setup

X7DB3 Quick Reference

Jumper	Description	Default Setting
J3P	3rd Power Fail Detect	Open (Disabled)
JBT1	CMOS Clear	(See Section 5-9)
JCF1	Compact Flash Master/Slave Select	Closed (Master)
JPG1	VGA Enable/Disable	Pins 1-2	(Enabled)
JPL1/ JPL2	JLAN1/JLAN2 Enable/Disable	Pins 1-2	(Enabled)
JWD	Watch Dog	Pins 1-2	(Reset)

Connector	Description
COM1/COM2	COM1/COM2 Serial Port Connector/Header
FAN 1-8	Fan Headers 1-8
IDE#1	IDE Hard Drive Connector
IDE#2	Compact Flash Card Connector
J7	BIOS Recovery
J22	Floppy Disk Drive Connector
JAR	Alarm Reset
JD1	Power LED (pins1-3)/Speaker Header (pins 4-7)
JF1	Front Control Panel Connector
JK1	Keylock Header
JL1	Chassis Intrusion Header
JLAN1/2	Gigabit Ethernet Ports
JOH1	Overheat LED
JPW1	Primary 24-Pin ATX Power Connector
JPW2	Auxiliary Power Connector
JPW3	Processor Power Connector
JUSB2/JUSB3	Extra USB Headers (JUSB2/3 and JUSB4)
JWF1	Compact Flash Card Power Connector
JWOL	Wake-on-LAN Header
JWOR	Wake-on-Ring Header
PSF	Power Supply Fail Header
Parallel	Parallel (Printer) Port
SATA0-SATA5	Intel SATA Ports
SAS0~3, SAS4~7	SAS 0~3, SAS 4~7 Ports
SGPIO1/SGPIO2	SGPIO Headers
SIM IPMI (Slot 7)	IPMI Connector
SMB	System Management Bus Header
SMBUS	System Management (I2C) Power Header
USB0/1	USB Ports

5-11

Image 45

SUPER MICRO Computer 6025B-3R user manual X7DB3 Quick Reference, Jumper Description Default Setting, Connector Description

Contents

Super Manual Revision 1.0c Release Date February 5 Preface About This ManualManual Organization Advanced Serverboard Setup System SafetyAdvanced Chassis Setup Bios Preface Table of Contents HDD LED NIC1 LED NIC2 LED Advanced Serverboard Setup Bios Advanced Chassis Setup Appendices Page Overview Chapter Introduction Processors Memory Serverboard FeaturesOnboard SAS PCI Expansion Slots Other Features Onboard Controllers/PortsATI Graphics Controller System Power Server Chassis FeaturesSAS Subsystem Front Control Panel Cooling System Intel 5000P Chipset System Block Diagram Headquarters Contacting SupermicroEurope Asia-Paciﬁc Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the Chassis Rails Installing the System into a Rack Installing Chassis Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Page Control Panel Buttons Chapter System Interface Control Panel LEDs SAS Drive Carrier LEDs Page Electrical Safety Precautions Chapter System Safety General Safety Precautions ESD Precautions Installing the Onboard Battery Operating Precautions Precautions Chapter Advanced Serverboard SetupHandling the Serverboard Unpacking Installing the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the Heatsink Connecting Cables Connecting Data CablesConnecting Power Cables Front Control Panel Header Pins JF1 Connecting the Control Panel Installing Memory Dimm Installation See FigureI/O Ports Memory Support 3a. Installing Dimm into Slot PCI Card Installation Adding PCI CardsPCI Expansion Slots Super X7DB3 Layout Serverboard Details Jumper Description Default Setting Connector DescriptionX7DB3 Quick Reference Connector Deﬁnitions Overheat/Fan Fail LED OH HDD LED Reset Button Power Fail LEDPower Button Universal Serial Bus USB0/1 Serial Ports Power Fail HeaderFan Headers Chassis Intrusion Extra Universal Serial Bus Headers Power LED/SpeakerATX PS/2 Keyboard and PS/2 Mouse Ports Overheat LED Wake-On-Ring Wake-On-LAN Alarm Reset JAR JLAN1/2 Ethernet PortsKeylock VGA Enable/Disable Jumper SettingsExplanation Jumpers Cmos Clear 3rd Power Supply Fail Detect Enable/Disable Jlan Enable/DisableCompact Flash Master Slave Onboard Indicators Watch Dog Enable/DisableJLAN1/JLAN2 LEDs Parallel Printer Port Pin Deﬁnitions Parallel Port Connector Floppy Drive Connector Pin Deﬁnitions J22 Floppy Connector Sata Ports IDE Connectors SB5 SAS PortsPage Static-Sensitive Devices Chapter Advanced Chassis SetupUnpacking Tools Required Front and Rear Chassis Views Control Panel System Fans Installing a new fanSystem Fan Failure Replacing System Fans Accessing the Drive Bays Drive Bay Installation/Removal Mounting a SAS drive in a drive carrier SAS Drive Installation Removing a SAS Drive Carrier Installing/removing hot-swap SAS drives DVD-ROM Installation Installing Components in the 3.5 Drive Bays Power Supply Failure Power SupplyRemoving/Replacing the Power Supply 6025B-3 6025B-3R Page How To Change the Conﬁguration Data System BiosStarting the Setup Utility Chapter Running Setup Main Bios SetupPress the Delete key to enter Setup Bios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System Date Type Transfer Mode LBA Mode ControlUltra DMA Mode Multi-Sector Transfers Sata Controller Mode Native Mode OperationSerial ATA Sata RAID Enable Parallel ATA Advanced Setup System MemoryExtended Memory Quick Boot Mode Boot FeaturesQuiet Boot Acpi Mode Cache Video Bios Area Memory Cache Cache System Bios AreaCache Base 0-512K Cache Base 512K-640K Reset Conﬁguration Data PCI Parity Error ForwardingDiscrete Mtrr Allocation PCI Conﬁguration Latency Timer Enable MasterLarge Disk Access Mode Serr Signal Condition Crystal Beach Features Memory Branch ModeClock Spectrum Feature Enabling Multi-Media Timer CPU Speed Advanced Processor Options KBC Clock Input Device ConﬁgurationSerial Port a Base I/O Address Serial Port B InterruptMode Parallel Port Event Log Validity DMI Event LoggingEvent Log Capacity View DMI Event Log COM Port Address Console RedirectionBaud Rate Console Type Hardware Monitor Logic CPU Temperature ThresholdVoltage Monitoring Fan Speed Control Modes CPU Temperature Threshold See note on Hardware Monitor Logic See note on Temperature Monitoring Bios Post Watch Dog Bios Post ErrorsSystem Event Logging Clear System Event Logging Timer for Loading OS Minutes OS Boot Watch DogSystem Event Log/System Event Log List Mode Time Out Option Realtime Sensor Data User Password Is Supervisor Password IsSet Supervisor Password Set User Password Boot Password on BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settings Fail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering Setup Invalid System Conﬁguration Data PS/2 Mouse Boot Summary ScreenDevice IRQ conﬂict Nnnn kB Extended RAM Passed Press F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Using the Adaptec RAID Conﬁguration Utility ARC Appendix C RAID and Software InstallationUsing the Array Conﬁguration Utility ACU Adaptec SAS HostRAID Managing Arrays Viewing Array PropertiesFrom the ARC menu, select Array Conﬁguration Utility ACU Creating Arrays Deleting Arrays To assign properties to the new array Assigning Array Properties Deleting a Bootable Array Adding a Bootable ArrayTo make an array bootable Ctrl+B Rebuilding Arrays Initializing Disk DrivesTo initialize drives To Rebuild an array To access the SAS utilities Using the SerialSelect Utility to Conﬁgure SAS Settings To set the controller conﬁguration To Set the Physical Conﬁguration Using the Disk Utilities To access the disk utilitiesFollowing options are available Exiting the Adaptec RAID Conﬁguration Utility Driver/Tool Installation Display Screen Installing Drivers Conﬁguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Appendix D System Speciﬁcations Power Supply 6025B-3 WeightPower Supply 6025B-3R Motherboard Regulatory Compliance Operating Environment