SAS Ports, SB5 | SUPER MICRO Computer 6025B-3R guide

Chapter 5: Advanced Serverboard Setup

SAS Ports

There are eight SAS (Serial

SAS Port Pin Deﬁnitions

(SAS0-3 ~ SAS4-7)

Attached SCSI) ports (one port for SAS0-3 and one port for SAS4-7) on the serverboard. See the table on the right for pin deﬁnitions.

Pin#	Deﬁnition
A1	Ground
A2	RX 0+
A3	RX 0-
A4	Ground
A5	RX 1+
A6	RX 1-
A7	Ground
A8	SB7
A9	SB3
A10	SB4
A11	SB5
A12	Ground
A13	RX 2+
A14	RX 2-
A15	Ground
A16	RX 3+
A17	RX 3-
A18	Ground

Pin # Deﬁnition

B1	Ground
B2	TX 0+
B3	TX 0-
B4	Ground
B5	TX 1+
B6	TX 1-
B7	Ground
B8	SB0
B9	SB1
B10	SB2
B11	SB6
B12	Ground
B13	TX 2+
B14	TX 2-
B15	Ground
B16	TX 3+
B17	TX 3-
B18	Ground

5-25

Image 59

SUPER MICRO Computer 6025B-3R user manual SAS Ports, SB5

Contents

Super Manual Revision 1.0c Release Date February 5 Manual Organization PrefaceAbout This Manual Bios System SafetyAdvanced Serverboard Setup Advanced Chassis Setup Preface Table of Contents HDD LED NIC1 LED NIC2 LED Advanced Serverboard Setup Bios Advanced Chassis Setup Appendices Page Overview Chapter Introduction PCI Expansion Slots Serverboard FeaturesProcessors Memory Onboard SAS ATI Graphics Controller Other FeaturesOnboard Controllers/Ports Front Control Panel Server Chassis FeaturesSystem Power SAS Subsystem Cooling System Intel 5000P Chipset System Block Diagram Asia-Paciﬁc Contacting SupermicroHeadquarters Europe Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Installing the Chassis Rails Installing the System into a Rack Installing Chassis Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Page Control Panel Buttons Chapter System Interface Control Panel LEDs SAS Drive Carrier LEDs Page Electrical Safety Precautions Chapter System Safety General Safety Precautions ESD Precautions Installing the Onboard Battery Operating Precautions Unpacking Chapter Advanced Serverboard SetupPrecautions Handling the Serverboard Installing the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables Front Control Panel Header Pins JF1 Connecting the Control Panel I/O Ports Installing MemoryDimm Installation See Figure Memory Support 3a. Installing Dimm into Slot PCI Expansion Slots PCI Card InstallationAdding PCI Cards Super X7DB3 Layout Serverboard Details X7DB3 Quick Reference Jumper Description Default SettingConnector Description Connector Deﬁnitions Overheat/Fan Fail LED OH HDD LED Universal Serial Bus USB0/1 Power Fail LEDReset Button Power Button Chassis Intrusion Power Fail HeaderSerial Ports Fan Headers Overheat LED Power LED/SpeakerExtra Universal Serial Bus Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Wake-On-Ring Wake-On-LAN Keylock Alarm Reset JARJLAN1/2 Ethernet Ports Cmos Clear Jumper SettingsVGA Enable/Disable Explanation Jumpers Compact Flash Master Slave 3rd Power Supply Fail Detect Enable/DisableJlan Enable/Disable JLAN1/JLAN2 LEDs Onboard IndicatorsWatch Dog Enable/Disable Parallel Printer Port Pin Deﬁnitions Parallel Port Connector Floppy Drive Connector Pin Deﬁnitions J22 Floppy Connector Sata Ports IDE Connectors SB5 SAS PortsPage Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Unpacking Front and Rear Chassis Views Control Panel Replacing System Fans Installing a new fanSystem Fans System Fan Failure Accessing the Drive Bays Drive Bay Installation/Removal Mounting a SAS drive in a drive carrier SAS Drive Installation Removing a SAS Drive Carrier Installing/removing hot-swap SAS drives DVD-ROM Installation Installing Components in the 3.5 Drive Bays 6025B-3 Power SupplyPower Supply Failure Removing/Replacing the Power Supply 6025B-3R Page Chapter System BiosHow To Change the Conﬁguration Data Starting the Setup Utility Press the Delete key to enter Setup Running SetupMain Bios Setup System Date Main Bios Setup Menu Main Setup FeaturesBios Date System Time Type Multi-Sector Transfers LBA Mode ControlTransfer Mode Ultra DMA Mode Parallel ATA Native Mode OperationSata Controller Mode Serial ATA Sata RAID Enable Extended Memory Advanced SetupSystem Memory Acpi Mode Boot FeaturesQuick Boot Mode Quiet Boot Cache Base 512K-640K Memory Cache Cache System Bios AreaCache Video Bios Area Cache Base 0-512K PCI Conﬁguration PCI Parity Error ForwardingReset Conﬁguration Data Discrete Mtrr Allocation Serr Signal Condition Enable MasterLatency Timer Large Disk Access Mode Enabling Multi-Media Timer Memory Branch ModeCrystal Beach Features Clock Spectrum Feature CPU Speed Advanced Processor Options Base I/O Address Device ConﬁgurationKBC Clock Input Serial Port a Parallel Port InterruptSerial Port B Mode View DMI Event Log DMI Event LoggingEvent Log Validity Event Log Capacity Console Type Console RedirectionCOM Port Address Baud Rate Fan Speed Control Modes CPU Temperature ThresholdHardware Monitor Logic Voltage Monitoring CPU Temperature Threshold See note on Hardware Monitor Logic See note on Temperature Monitoring Clear System Event Logging Bios Post ErrorsBios Post Watch Dog System Event Logging Time Out Option OS Boot Watch DogTimer for Loading OS Minutes System Event Log/System Event Log List Mode Realtime Sensor Data Set User Password Supervisor Password IsUser Password Is Set Supervisor Password Boot Priority Order/Excluded from Boot Orders BootPassword on Boot Exit Appendix a Bios Post Messages Check date and time settings System Cmos checksum bad Default conﬁguration usedSystem timer error Real time clock error Entering Setup System cache error Cache disabledFail-Safe Timer NMI Failed Allocation Error for device Nnnn kB Extended RAM Passed PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Device IRQ conﬂict Video Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup System Bios shadowedPage Post Code Description Appendix B Bios Post CodesRecoverable Post Errors Terminal Post Errors Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Adaptec SAS HostRAID Appendix C RAID and Software InstallationUsing the Adaptec RAID Conﬁguration Utility ARC Using the Array Conﬁguration Utility ACU From the ARC menu, select Array Conﬁguration Utility ACU Managing ArraysViewing Array Properties Creating Arrays Deleting Arrays To assign properties to the new array Assigning Array Properties Ctrl+B Adding a Bootable ArrayDeleting a Bootable Array To make an array bootable To Rebuild an array Initializing Disk DrivesRebuilding Arrays To initialize drives To access the SAS utilities Using the SerialSelect Utility to Conﬁgure SAS Settings To set the controller conﬁguration To Set the Physical Conﬁguration Following options are available Using the Disk UtilitiesTo access the disk utilities Exiting the Adaptec RAID Conﬁguration Utility Driver/Tool Installation Display Screen Installing Drivers Conﬁguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Appendix D System Speciﬁcations Motherboard WeightPower Supply 6025B-3 Power Supply 6025B-3R Regulatory Compliance Operating Environment