Extra Universal Serial Bus Headers | SUPER MICRO Computer 6025B-3

SUPERSERVER 6025B-3/6025B-3R User's Manual

Extra Universal Serial Bus Headers

Front Panel Universal Serial Bus Pin Deﬁnitions (JUSB2/JUSB3)

Three additional USB headers (USB2/3 and USB4) are included on the serverboard. These may be used for front side access. A USB cable (not included) is needed for the con- nection. See the table on the right for pin deﬁnitions.

USB2

Pin # Deﬁnition

1+5V

2PO-

3PO+

4Ground

5Key

USB3, USB4

Pin # Deﬁnition

1+5V

2PO-

3PO+

4Ground

5NC

Power LED/Speaker

On the JD1 header, pins 1-3 are for

apower LED, pins 4-7 are for the speaker. See the table on the right for speaker pin definitions. Note: The speaker connector pins are for use with an external speaker. If you wish to use the onboard speaker, you should close pins 6-7 with a jumper.

Speaker Connector

Pin Deﬁnitions (JD1)

Pin #	Function		Deﬁnition
4	+		Speaker data (red wire)

5	Key		No connection

6Key

7Speaker data

ATX PS/2 Keyboard and PS/2 Mouse Ports

The ATX PS/2 keyboard and the PS/2 mouse ports are located beside the USB ports. See the table on the right for pin deﬁnitions.

Overheat LED

Connect an LED to the JOH1 header to provide warning of a chassis over- heating condition. See the table on the right for pin deﬁnitions.

PS/2 Keyboard and

Mouse Ports

Pin Deﬁnitions

Pin# Deﬁnition

1Data

2NC

3Ground

4VCC

5Clock

6NC

Overheat LED

Pin Deﬁnitions

(JOH1)

Pin# Deﬁnition

1+5V

2OH Active

5-16

Image 50

SUPER MICRO Computer 6025B-3 Extra Universal Serial Bus Headers, Power LED/Speaker, ATX PS/2 Keyboard and PS/2 Mouse Ports

Contents

Super Manual Revision 1.0c Release Date February 5 Manual Organization PrefaceAbout This Manual Advanced Chassis Setup System SafetyAdvanced Serverboard Setup Bios Preface Table of Contents Advanced Serverboard Setup HDD LED NIC1 LED NIC2 LED Advanced Chassis Setup Bios Appendices Page Chapter Introduction Overview Onboard SAS Serverboard FeaturesProcessors Memory PCI Expansion Slots ATI Graphics Controller Other FeaturesOnboard Controllers/Ports SAS Subsystem Server Chassis FeaturesSystem Power Front Control Panel Intel 5000P Chipset System Block Diagram Cooling System Europe Contacting SupermicroHeadquarters Asia-Paciﬁc Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Installing the System into a Rack Installing the Chassis Rails Installing the Server into the Rack Installing Chassis Rails Installing the Server into a Telco Rack Installing the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Page Chapter System Interface Control Panel Buttons Control Panel LEDs SAS Drive Carrier LEDs Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Handling the Serverboard Chapter Advanced Serverboard SetupPrecautions Unpacking Processor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel Front Control Panel Header Pins JF1 I/O Ports Installing MemoryDimm Installation See Figure 3a. Installing Dimm into Slot Memory Support PCI Expansion Slots PCI Card InstallationAdding PCI Cards Serverboard Details Super X7DB3 Layout X7DB3 Quick Reference Jumper Description Default SettingConnector Description Connector Deﬁnitions HDD LED Overheat/Fan Fail LED OH Power Button Power Fail LEDReset Button Universal Serial Bus USB0/1 Fan Headers Power Fail HeaderSerial Ports Chassis Intrusion ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerExtra Universal Serial Bus Headers Overheat LED Wake-On-LAN Wake-On-Ring Keylock Alarm Reset JARJLAN1/2 Ethernet Ports Explanation Jumpers Jumper SettingsVGA Enable/Disable Cmos Clear Compact Flash Master Slave 3rd Power Supply Fail Detect Enable/DisableJlan Enable/Disable JLAN1/JLAN2 LEDs Onboard IndicatorsWatch Dog Enable/Disable Parallel Port Connector Parallel Printer Port Pin Deﬁnitions Floppy Connector Floppy Drive Connector Pin Deﬁnitions J22 IDE Connectors Sata Ports SAS Ports SB5Page Unpacking Chapter Advanced Chassis SetupStatic-Sensitive Devices Tools Required Control Panel Front and Rear Chassis Views System Fan Failure Installing a new fanSystem Fans Replacing System Fans Drive Bay Installation/Removal Accessing the Drive Bays SAS Drive Installation Mounting a SAS drive in a drive carrier Installing/removing hot-swap SAS drives Removing a SAS Drive Carrier Installing Components in the 3.5 Drive Bays DVD-ROM Installation Removing/Replacing the Power Supply Power SupplyPower Supply Failure 6025B-3 6025B-3R Page Starting the Setup Utility System BiosHow To Change the Conﬁguration Data Chapter Press the Delete key to enter Setup Running SetupMain Bios Setup System Time Main Bios Setup Menu Main Setup FeaturesBios Date System Date Type Ultra DMA Mode LBA Mode ControlTransfer Mode Multi-Sector Transfers Serial ATA Sata RAID Enable Native Mode OperationSata Controller Mode Parallel ATA Extended Memory Advanced SetupSystem Memory Quiet Boot Boot FeaturesQuick Boot Mode Acpi Mode Cache Base 0-512K Memory Cache Cache System Bios AreaCache Video Bios Area Cache Base 512K-640K Discrete Mtrr Allocation PCI Parity Error ForwardingReset Conﬁguration Data PCI Conﬁguration Large Disk Access Mode Enable MasterLatency Timer Serr Signal Condition Clock Spectrum Feature Memory Branch ModeCrystal Beach Features Enabling Multi-Media Timer Advanced Processor Options CPU Speed Serial Port a Device ConﬁgurationKBC Clock Input Base I/O Address Mode InterruptSerial Port B Parallel Port Event Log Capacity DMI Event LoggingEvent Log Validity View DMI Event Log Baud Rate Console RedirectionCOM Port Address Console Type Voltage Monitoring CPU Temperature ThresholdHardware Monitor Logic Fan Speed Control Modes CPU Temperature Threshold See note on Temperature Monitoring Hardware Monitor Logic See note on System Event Logging Bios Post ErrorsBios Post Watch Dog Clear System Event Logging System Event Log/System Event Log List Mode OS Boot Watch DogTimer for Loading OS Minutes Time Out Option Realtime Sensor Data Set Supervisor Password Supervisor Password IsUser Password Is Set User Password Boot Priority Order/Excluded from Boot Orders BootPassword on Boot Exit Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default conﬁguration usedSystem timer error Check date and time settings Allocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering Setup Device IRQ conﬂict PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Nnnn kB Extended RAM Passed System Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Using the Array Conﬁguration Utility ACU Appendix C RAID and Software InstallationUsing the Adaptec RAID Conﬁguration Utility ARC Adaptec SAS HostRAID From the ARC menu, select Array Conﬁguration Utility ACU Managing ArraysViewing Array Properties Deleting Arrays Creating Arrays Assigning Array Properties To assign properties to the new array To make an array bootable Adding a Bootable ArrayDeleting a Bootable Array Ctrl+B To initialize drives Initializing Disk DrivesRebuilding Arrays To Rebuild an array Using the SerialSelect Utility to Conﬁgure SAS Settings To access the SAS utilities To set the controller conﬁguration To Set the Physical Conﬁguration Following options are available Using the Disk UtilitiesTo access the disk utilities Exiting the Adaptec RAID Conﬁguration Utility Installing Drivers Driver/Tool Installation Display Screen Conﬁguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Appendix D System Speciﬁcations Power Supply 6025B-3R WeightPower Supply 6025B-3 Motherboard Operating Environment Regulatory Compliance