Removing the Top Cover | SUPER MICRO Computer FAN0103L4 specs

Chapter 4: Chassis Setup and Maintenance

When mounting the SC743 into a rack or changing the power supply, it is necessary to remove the top cover from the chassis.

Removing the Top Cover

Removing the Top Cover of the Chassis

1.Disconnect the chassis from any power source.

2.Press the release tab at the back of the top cover.

3.Slide the back cover off the chassis.

Release Tab

12

13

Figure 4-2: Removing the Top Cover

4-3

Image 23

SUPER MICRO Computer FAN0103L4 user manual Removing the Top Cover of the Chassis, Release Tab

Contents

Super SC743 Chassis Manual About This Manual Preface Introduction Manual Organization Table of Contents Appendix B Power Supply Specifications Part Numbers Chapter IntroductionOverview Shipping List Where to get Replacement Components Asia-Pacific Contacting SupermicroHeadquarters Europe Returning Merchandise for Service Preparing for Setup Chapter System Safety Electrical Safety Precautions System Safety Page Chassis Power SupplyChapter Chassis Components Components Front Control Panel Where to get Replacement Components Front Control Panel Control Panel LEDs Control Panel ButtonsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Removing the Side Cover of the Chassis Disconnecting the Chassis from the Power SourceRemoving the Chassis Side and Top Covers Removing the Side Cover Release Tab Removing the Top CoverRemoving the Top Cover of the Chassis Installing Hard Drive Carriers Accessing the Hot-Swappable Drive CarriersAccessing and Removing Hard Drive Carriers Removing the Dummy Drive Installing Hard Drives into the Drive CarriersInstalling Hard Drives Installing Fixed Hard Drives in SC743i Series Chassis Models Removing the Storage Module Configuring the Storage ModuleStorage Module Options Storage Module Mobile Rack Bracket Devices Configuring the Storage Module for 5.25 Devices Removing and Replacing Mid-chassis Fans Removing and Replacing the System FansSC743TQ-865B-SQ Cooling System Standard Cooling Systems 10 Removing Rear Chassis Fans Removing Rear Chassis Fans Removing the Air Shroud Removing the Air Shroud Installing the Motherboard Installing the MotherboardPrior to Installing the Motherboard Motherboard Installation 12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage Installing the Power Supply Power Supply465, 500, 665 and 865 Watt Power Supplies Remove Screws14 15 Removing the Interior Chassis Screws on the Power Supply 16 Installing the 760 Watt Power Supply Watt Power Supply 17 Accessing the Interior Backplane/Midplane Space Accessing the Interior Space Installing the Driver Select Enclosure Services Device and click Next Installing the Driver Alternative Procedure SC743 Chassis Manual Unpacking the System Chapter Rack InstallationChoosing a Setup Location General Server Precautions Rack Precautions Rack Mounting Considerations Ambient Operating Temperature Installing the Inner Chassis Rails Installing the Chassis Rack Mounting RailsBefore Installing the Chassis Rails Middle Rail End Rail End Bracket Installing the Outer Chassis Rails Mounting the Chassis into a Rack Outer Rail Assemblies Inner Rails SC743S2 Series Scsi Type Length Description Appendix a Cables, Screws Other AccessoriesOverview Cables Included with the SC743 Chassis SC743S1 Series Scsi Type Length SC743i Series Type Length Description SC743T Series SAS/SATASC743TQ Series SATA/SCSI Front Panel to the Motherboard Extending Power CablesPower Cable Extenders Number of Pins Length DVD-ROM, CD-ROM, and Floppy Drive Chassis Screws Power Supply Options Appendix B Power Supply Specifications MFR Rated AC Voltage +5V standby +12V +3.3V 865W MFR Rated AC Voltage +5V standby +12V +3.3V 665WMFR Rated AC Voltage +5V standby +12V +3.3V R760W Product Features Appendix C CSE-M34S/CSE-M34T Mobile Rack Specifications Supported Operating Systems Packing List Additional Information Jumper Description Setting Front Connectors and JumpersJumper Settings Page Figure C-2 Jumper Locations Jumper Settings and Locations for the CSE-M35T Sata Release Buttons Installation ProceduresInstalling the CSE-M35S Backplane Accessing Hot-Swappable Drives Figure C-5 Installing the Drive into the Drive Tray Installing a Drive into the Drive Tray Figure C-6 Accessing the Backplane Accessing the Backplane SC743 Chassis Manual System Monitoring Appendix D M35TQ Mobile Rack Specificaitons An Important Note to the User ESD Safety GuidelinesGeneral Safety Guidelines Introduction to the SAS-M35TQ Backplane Front Connectors Figure D-1 Front Connectors 5. I2C Connectors Front Connectors and Pin DefinitionsMobile Rack Main Power Connectors Jtag Connector Activity LED Header Upgrade ConnectorFan Connector 7. Sideband Headers JP40 Front Jumper Locations and Pin Definitions Buzzer alarm is triggered by the following conditions Buzzer and Chip Reset Jumper SettingsJumper Settings Fan Jumper Settings Fan Jumper Settings I2C Setting Default I2C and Sgpio Modes and Jumper SettingsI2C/SGPIO Settings Jumper Figure D-6 Rear Connectors and LED Indicators Rear Connectors and LED Indicators Hard Drive Activity Rear SAS/SATA ConnectorsRear LED Indicators Drive Number Tools Required Preparing for InstallationImportant Safety Guidelines Safety Guidelines Removing Hard Drives from the Mobile Rack Installation ProceduresInstalling Hard Drives into the Mobile Rack Release Button Dummy Drive Drive Carrier Installing a Hard Drive into the Hard Drive Carrier SAS/SATA or Scsi Hard Drive Drive Tray Figure D-10 Installing a Hard Drive Removing the Exhaust Fan and Connecting SAS/SATA Cables Connecting Cables to the Mobile Rack Figure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Backplane Screw Locations Additional Optional Installation Information Appendix E SAS-743TQ Backplane Specifications Introduction to the SAS-743TQ Backplane An Important Note to Users Figure E-1 Front Connectors Front Connectors #3. MG9072 Chip Front Connector and Pin Definitions#1. and 2. Jtag Connector and Upgrade Connectors #4. Backplane Main Power Connectors #10. #17. SAS Ports #8. and #9. I2C Connectors#6. and #7. Sideband Headers JP34 JP41 Connector Pins Jumper Setting SAS Port Connections in I2C and Sgpio Settings I2C and Sgpio Mode Jumper Settings OH/Drive Fail LED Front LED IndicatorsState Specification SAS Drive Number J15 Appendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Figure F-1 Front Connectors Connectors and Jumpers Front Connector and Jumper Pin Definitions JP18 MM2 Explanation of JumpersJP25 Normal State Indicator Status Front LED Indicator Figure F-4 Rear Connectors Rear Sata Connectors Rear Connectors Rear LEDs Appendix F SATA-743 Backplane Specifications