Mobile Rack Main Power Connectors | SUPER MICRO Computer FAN0103L4

Appendix D: M35TQ Mobile Rack Specifications

D-8 Front Connectors and Pin Definitions

1. Mobile Rack Main Power Connectors

The 4-pin power connectors, designated JP10 and JP13, provide power to the mobile rack. See the table on the right for pin definitions.

2. MG9072 Chip

The MG9072 is an enclosure management chip that supports the SES-2 controller and SES-2 protocols.

3. JTAG Connector

The JTAG connector, designated JP47, is used for diagnostic purposes only.

4. and 5. I2C Connectors

The I2C connectors, designated JP44 and JP45, are used to monitor the HDD activity and status. See the table on the right for pin definitions.

Mobile rack Main Power 4-Pin Connector

Pin# Definition

1+12V

2 and 3	Ground

4+5V

I2C Connector

Pin Definitions

Pin# Definition

1Data

2Ground

3Clock

4No Connection

D-5

Image 69

SUPER MICRO Computer FAN0103L4 Front Connectors and Pin Definitions, Mobile Rack Main Power Connectors, MG9072 Chip

Contents

Super SC743 Chassis Manual About This Manual Preface Introduction Manual Organization Table of Contents Appendix B Power Supply Specifications Overview Chapter IntroductionShipping List Part Numbers Where to get Replacement Components Headquarters Contacting SupermicroEurope Asia-Pacific Returning Merchandise for Service Preparing for Setup Chapter System Safety Electrical Safety Precautions System Safety Page Chapter Chassis Components Power SupplyComponents Chassis Front Control Panel Where to get Replacement Components Front Control Panel Control Panel LEDs Control Panel ButtonsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Removing the Chassis Side and Top Covers Disconnecting the Chassis from the Power SourceRemoving the Side Cover Removing the Side Cover of the Chassis Removing the Top Cover Removing the Top Cover of the ChassisRelease Tab Accessing the Hot-Swappable Drive Carriers Accessing and Removing Hard Drive CarriersInstalling Hard Drive Carriers Installing Hard Drives into the Drive Carriers Installing Hard DrivesRemoving the Dummy Drive Installing Fixed Hard Drives in SC743i Series Chassis Models Configuring the Storage Module Storage Module OptionsRemoving the Storage Module Storage Module Mobile Rack Bracket Devices Configuring the Storage Module for 5.25 Devices SC743TQ-865B-SQ Cooling System Removing and Replacing the System FansStandard Cooling Systems Removing and Replacing Mid-chassis Fans 10 Removing Rear Chassis Fans Removing Rear Chassis Fans Removing the Air Shroud Removing the Air Shroud Prior to Installing the Motherboard Installing the MotherboardMotherboard Installation Installing the Motherboard 12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage Power Supply 465, 500, 665 and 865 Watt Power SuppliesInstalling the Power Supply Remove Screws14 15 Removing the Interior Chassis Screws on the Power Supply 16 Installing the 760 Watt Power Supply Watt Power Supply 17 Accessing the Interior Backplane/Midplane Space Accessing the Interior Space Installing the Driver Select Enclosure Services Device and click Next Installing the Driver Alternative Procedure SC743 Chassis Manual Chapter Rack Installation Choosing a Setup LocationUnpacking the System General Server Precautions Rack Precautions Rack Mounting Considerations Ambient Operating Temperature Installing the Chassis Rack Mounting Rails Before Installing the Chassis RailsInstalling the Inner Chassis Rails Middle Rail End Rail End Bracket Installing the Outer Chassis Rails Mounting the Chassis into a Rack Outer Rail Assemblies Inner Rails Overview Cables Included with the SC743 Chassis Appendix a Cables, Screws Other AccessoriesSC743S1 Series Scsi Type Length SC743S2 Series Scsi Type Length Description SC743T Series SAS/SATA SC743TQ Series SATA/SCSISC743i Series Type Length Description Extending Power Cables Power Cable Extenders Number of Pins LengthFront Panel to the Motherboard DVD-ROM, CD-ROM, and Floppy Drive Chassis Screws Power Supply Options Appendix B Power Supply Specifications MFR Rated AC Voltage +5V standby +12V +3.3V 665W MFR Rated AC Voltage +5V standby +12V +3.3V R760WMFR Rated AC Voltage +5V standby +12V +3.3V 865W Product Features Appendix C CSE-M34S/CSE-M34T Mobile Rack Specifications Supported Operating Systems Packing List Additional Information Front Connectors and Jumpers Jumper SettingsJumper Description Setting Page Figure C-2 Jumper Locations Jumper Settings and Locations for the CSE-M35T Sata Installing the CSE-M35S Backplane Installation ProceduresAccessing Hot-Swappable Drives Release Buttons Figure C-5 Installing the Drive into the Drive Tray Installing a Drive into the Drive Tray Figure C-6 Accessing the Backplane Accessing the Backplane SC743 Chassis Manual System Monitoring Appendix D M35TQ Mobile Rack Specificaitons ESD Safety Guidelines General Safety GuidelinesAn Important Note to the User Introduction to the SAS-M35TQ Backplane Front Connectors Figure D-1 Front Connectors Mobile Rack Main Power Connectors Front Connectors and Pin DefinitionsJtag Connector 5. I2C Connectors Fan Connector Upgrade Connector7. Sideband Headers Activity LED Header JP40 Front Jumper Locations and Pin Definitions Buzzer and Chip Reset Jumper Settings Jumper SettingsBuzzer alarm is triggered by the following conditions Fan Jumper Settings Fan Jumper Settings I2C and Sgpio Modes and Jumper Settings I2C/SGPIO Settings JumperI2C Setting Default Figure D-6 Rear Connectors and LED Indicators Rear Connectors and LED Indicators Rear LED Indicators Rear SAS/SATA ConnectorsDrive Number Hard Drive Activity Important Safety Guidelines Preparing for InstallationSafety Guidelines Tools Required Installing Hard Drives into the Mobile Rack Installation ProceduresRelease Button Removing Hard Drives from the Mobile Rack Dummy Drive Drive Carrier Installing a Hard Drive into the Hard Drive Carrier SAS/SATA or Scsi Hard Drive Drive Tray Figure D-10 Installing a Hard Drive Removing the Exhaust Fan and Connecting SAS/SATA Cables Connecting Cables to the Mobile Rack Figure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Backplane Screw Locations Additional Optional Installation Information Appendix E SAS-743TQ Backplane Specifications Introduction to the SAS-743TQ Backplane An Important Note to Users Figure E-1 Front Connectors Front Connectors #1. and 2. Jtag Connector and Upgrade Connectors Front Connector and Pin Definitions#4. Backplane Main Power Connectors #3. MG9072 Chip #8. and #9. I2C Connectors #6. and #7. Sideband Headers#10. #17. SAS Ports JP34 JP41 Connector Pins Jumper Setting SAS Port Connections in I2C and Sgpio Settings I2C and Sgpio Mode Jumper Settings Front LED Indicators State SpecificationOH/Drive Fail LED SAS Drive Number J15 Appendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Figure F-1 Front Connectors Connectors and Jumpers Front Connector and Jumper Pin Definitions Explanation of Jumpers JP25JP18 MM2 Normal State Indicator Status Front LED Indicator Figure F-4 Rear Connectors Rear Sata Connectors Rear Connectors Rear LEDs Appendix F SATA-743 Backplane Specifications