Installation Procedures | SUPER MICRO Computer FAN0103L4 instruction

Apppendix C: CSE-M34S/CSE-M34T Mobile Rack Specifications

Installation Procedures

Installing the CSE-M35S Backplane

1.SCSI IDs are assigned automatically by the backplane. Do not set IDs man- ually on the drives. See the previous section for SCSI ID jumper settings.

2.SCSI termination is enabled by default on the SCSI backplane.

Accessing Hot-Swappable Drives

1.Push the release button located beside each drive's LED.

2.Lift up on the drive's handle.

3.Carefully pull the drives out of the storage module.

2

1

Release Buttons

Figure C-3: Releasing the Drives

3

Figure C-4: Removing the Drives

C-7

Image 61

SUPER MICRO Computer FAN0103L4 Installation Procedures, Installing the CSE-M35S Backplane, Accessing Hot-Swappable Drives

Contents

Super SC743 Chassis Manual About This Manual Preface Introduction Manual Organization Table of Contents Appendix B Power Supply Specifications Overview Chapter IntroductionShipping List Part Numbers Where to get Replacement Components Headquarters Contacting SupermicroEurope Asia-Pacific Returning Merchandise for Service Preparing for Setup Chapter System Safety Electrical Safety Precautions System Safety Page Chapter Chassis Components Power SupplyComponents Chassis Front Control Panel Where to get Replacement Components Front Control Panel Control Panel LEDs Control Panel ButtonsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Removing the Chassis Side and Top Covers Disconnecting the Chassis from the Power SourceRemoving the Side Cover Removing the Side Cover of the Chassis Removing the Top Cover of the Chassis Removing the Top CoverRelease Tab Accessing and Removing Hard Drive Carriers Accessing the Hot-Swappable Drive CarriersInstalling Hard Drive Carriers Installing Hard Drives Installing Hard Drives into the Drive CarriersRemoving the Dummy Drive Installing Fixed Hard Drives in SC743i Series Chassis Models Storage Module Options Configuring the Storage ModuleRemoving the Storage Module Storage Module Mobile Rack Bracket Devices Configuring the Storage Module for 5.25 Devices SC743TQ-865B-SQ Cooling System Removing and Replacing the System FansStandard Cooling Systems Removing and Replacing Mid-chassis Fans 10 Removing Rear Chassis Fans Removing Rear Chassis Fans Removing the Air Shroud Removing the Air Shroud Prior to Installing the Motherboard Installing the MotherboardMotherboard Installation Installing the Motherboard 12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage 465, 500, 665 and 865 Watt Power Supplies Power SupplyInstalling the Power Supply Remove Screws14 15 Removing the Interior Chassis Screws on the Power Supply 16 Installing the 760 Watt Power Supply Watt Power Supply 17 Accessing the Interior Backplane/Midplane Space Accessing the Interior Space Installing the Driver Select Enclosure Services Device and click Next Installing the Driver Alternative Procedure SC743 Chassis Manual Choosing a Setup Location Chapter Rack InstallationUnpacking the System General Server Precautions Rack Precautions Rack Mounting Considerations Ambient Operating Temperature Before Installing the Chassis Rails Installing the Chassis Rack Mounting RailsInstalling the Inner Chassis Rails Middle Rail End Rail End Bracket Installing the Outer Chassis Rails Mounting the Chassis into a Rack Outer Rail Assemblies Inner Rails Overview Cables Included with the SC743 Chassis Appendix a Cables, Screws Other AccessoriesSC743S1 Series Scsi Type Length SC743S2 Series Scsi Type Length Description SC743TQ Series SATA/SCSI SC743T Series SAS/SATASC743i Series Type Length Description Power Cable Extenders Number of Pins Length Extending Power CablesFront Panel to the Motherboard DVD-ROM, CD-ROM, and Floppy Drive Chassis Screws Power Supply Options Appendix B Power Supply Specifications MFR Rated AC Voltage +5V standby +12V +3.3V R760W MFR Rated AC Voltage +5V standby +12V +3.3V 665WMFR Rated AC Voltage +5V standby +12V +3.3V 865W Product Features Appendix C CSE-M34S/CSE-M34T Mobile Rack Specifications Supported Operating Systems Packing List Additional Information Jumper Settings Front Connectors and JumpersJumper Description Setting Page Figure C-2 Jumper Locations Jumper Settings and Locations for the CSE-M35T Sata Installing the CSE-M35S Backplane Installation ProceduresAccessing Hot-Swappable Drives Release Buttons Figure C-5 Installing the Drive into the Drive Tray Installing a Drive into the Drive Tray Figure C-6 Accessing the Backplane Accessing the Backplane SC743 Chassis Manual System Monitoring Appendix D M35TQ Mobile Rack Specificaitons General Safety Guidelines ESD Safety GuidelinesAn Important Note to the User Introduction to the SAS-M35TQ Backplane Front Connectors Figure D-1 Front Connectors Mobile Rack Main Power Connectors Front Connectors and Pin DefinitionsJtag Connector 5. I2C Connectors Fan Connector Upgrade Connector7. Sideband Headers Activity LED Header JP40 Front Jumper Locations and Pin Definitions Jumper Settings Buzzer and Chip Reset Jumper SettingsBuzzer alarm is triggered by the following conditions Fan Jumper Settings Fan Jumper Settings I2C/SGPIO Settings Jumper I2C and Sgpio Modes and Jumper SettingsI2C Setting Default Figure D-6 Rear Connectors and LED Indicators Rear Connectors and LED Indicators Rear LED Indicators Rear SAS/SATA ConnectorsDrive Number Hard Drive Activity Important Safety Guidelines Preparing for InstallationSafety Guidelines Tools Required Installing Hard Drives into the Mobile Rack Installation ProceduresRelease Button Removing Hard Drives from the Mobile Rack Dummy Drive Drive Carrier Installing a Hard Drive into the Hard Drive Carrier SAS/SATA or Scsi Hard Drive Drive Tray Figure D-10 Installing a Hard Drive Removing the Exhaust Fan and Connecting SAS/SATA Cables Connecting Cables to the Mobile Rack Figure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Backplane Screw Locations Additional Optional Installation Information Appendix E SAS-743TQ Backplane Specifications Introduction to the SAS-743TQ Backplane An Important Note to Users Figure E-1 Front Connectors Front Connectors #1. and 2. Jtag Connector and Upgrade Connectors Front Connector and Pin Definitions#4. Backplane Main Power Connectors #3. MG9072 Chip #6. and #7. Sideband Headers #8. and #9. I2C Connectors#10. #17. SAS Ports JP34 JP41 Connector Pins Jumper Setting SAS Port Connections in I2C and Sgpio Settings I2C and Sgpio Mode Jumper Settings State Specification Front LED IndicatorsOH/Drive Fail LED SAS Drive Number J15 Appendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Figure F-1 Front Connectors Connectors and Jumpers Front Connector and Jumper Pin Definitions JP25 Explanation of JumpersJP18 MM2 Normal State Indicator Status Front LED Indicator Figure F-4 Rear Connectors Rear Sata Connectors Rear Connectors Rear LEDs Appendix F SATA-743 Backplane Specifications