Front LED Indicator | SUPER MICRO Computer FAN0103L4 manual

SC743 Chassis Manual

Front LED Indicator

SUPER	R			JP25
	R	SATA743		pb
		SATA743	REV 3.00	pb		D3
							JP35	JP18
							OH LED
							JP18: BUZZER RESET
							JP35: GEM24 RST
				48
				49
				64	16	JP25: OH TEMP.
				1	H3	JP25: OH TEMP.
						OPEN 45 C
						1-2	50 C
						2-3	55 C

BZ1

MM2

75H

JP10	JP13
+12V GND GND +5V	+12V GND GND +5V

ACT IN JP26

#7		#5	#3	#1
#6	#4		#2	#0

Figure F-3: Front LED

Front Panel LEDs

LED

Normal State

Indicator Status

D3: OH LED

Off

Red indicator light is on when an overheat condition occurs.

F-6

Image 100

SUPER MICRO Computer FAN0103L4 user manual Front LED Indicator, Normal State Indicator Status

Contents

Super SC743 Chassis Manual Preface About This Manual Manual Organization Introduction Table of Contents Appendix B Power Supply Specifications Chapter Introduction OverviewShipping List Part Numbers Where to get Replacement Components Contacting Supermicro HeadquartersEurope Asia-Pacific Returning Merchandise for Service Chapter System Safety Preparing for Setup Electrical Safety Precautions System Safety Page Power Supply Chapter Chassis ComponentsComponents Chassis Where to get Replacement Components Front Control Panel Front Control Panel Control Panel Buttons Control Panel LEDsPage Page SC743 Chassis Manual Chapter Chassis Setup and Maintenance Disconnecting the Chassis from the Power Source Removing the Chassis Side and Top CoversRemoving the Side Cover Removing the Side Cover of the Chassis Removing the Top Cover of the Chassis Removing the Top CoverRelease Tab Accessing and Removing Hard Drive Carriers Accessing the Hot-Swappable Drive CarriersInstalling Hard Drive Carriers Installing Hard Drives Installing Hard Drives into the Drive CarriersRemoving the Dummy Drive Installing Fixed Hard Drives in SC743i Series Chassis Models Storage Module Options Configuring the Storage ModuleRemoving the Storage Module Configuring the Storage Module for 5.25 Devices Storage Module Mobile Rack Bracket Devices Removing and Replacing the System Fans SC743TQ-865B-SQ Cooling SystemStandard Cooling Systems Removing and Replacing Mid-chassis Fans Removing Rear Chassis Fans 10 Removing Rear Chassis Fans Removing the Air Shroud Removing the Air Shroud Installing the Motherboard Prior to Installing the MotherboardMotherboard Installation Installing the Motherboard 12 Installing the Motherboard Installing Expansion Cards Installing Expansion CardsPage 465, 500, 665 and 865 Watt Power Supplies Power SupplyInstalling the Power Supply 15 Removing the Interior Chassis Screws on the Power Supply Remove Screws14 Watt Power Supply 16 Installing the 760 Watt Power Supply Accessing the Interior Space 17 Accessing the Interior Backplane/Midplane Space Installing the Driver Installing the Driver Alternative Procedure Select Enclosure Services Device and click Next SC743 Chassis Manual Choosing a Setup Location Chapter Rack InstallationUnpacking the System Rack Precautions General Server Precautions Ambient Operating Temperature Rack Mounting Considerations Before Installing the Chassis Rails Installing the Chassis Rack Mounting RailsInstalling the Inner Chassis Rails Installing the Outer Chassis Rails Middle Rail End Rail End Bracket Outer Rail Assemblies Inner Rails Mounting the Chassis into a Rack Appendix a Cables, Screws Other Accessories Overview Cables Included with the SC743 ChassisSC743S1 Series Scsi Type Length SC743S2 Series Scsi Type Length Description SC743TQ Series SATA/SCSI SC743T Series SAS/SATASC743i Series Type Length Description Power Cable Extenders Number of Pins Length Extending Power CablesFront Panel to the Motherboard Chassis Screws DVD-ROM, CD-ROM, and Floppy Drive Appendix B Power Supply Specifications Power Supply Options MFR Rated AC Voltage +5V standby +12V +3.3V R760W MFR Rated AC Voltage +5V standby +12V +3.3V 665WMFR Rated AC Voltage +5V standby +12V +3.3V 865W Appendix C CSE-M34S/CSE-M34T Mobile Rack Specifications Product Features Packing List Supported Operating Systems Additional Information Jumper Settings Front Connectors and JumpersJumper Description Setting Page Jumper Settings and Locations for the CSE-M35T Sata Figure C-2 Jumper Locations Installation Procedures Installing the CSE-M35S BackplaneAccessing Hot-Swappable Drives Release Buttons Installing a Drive into the Drive Tray Figure C-5 Installing the Drive into the Drive Tray Accessing the Backplane Figure C-6 Accessing the Backplane SC743 Chassis Manual Appendix D M35TQ Mobile Rack Specificaitons System Monitoring General Safety Guidelines ESD Safety GuidelinesAn Important Note to the User Introduction to the SAS-M35TQ Backplane Figure D-1 Front Connectors Front Connectors Front Connectors and Pin Definitions Mobile Rack Main Power ConnectorsJtag Connector 5. I2C Connectors Upgrade Connector Fan Connector7. Sideband Headers Activity LED Header Front Jumper Locations and Pin Definitions JP40 Jumper Settings Buzzer and Chip Reset Jumper SettingsBuzzer alarm is triggered by the following conditions Fan Jumper Settings Fan Jumper Settings I2C/SGPIO Settings Jumper I2C and Sgpio Modes and Jumper SettingsI2C Setting Default Rear Connectors and LED Indicators Figure D-6 Rear Connectors and LED Indicators Rear SAS/SATA Connectors Rear LED IndicatorsDrive Number Hard Drive Activity Preparing for Installation Important Safety GuidelinesSafety Guidelines Tools Required Installation Procedures Installing Hard Drives into the Mobile RackRelease Button Removing Hard Drives from the Mobile Rack Installing a Hard Drive into the Hard Drive Carrier Dummy Drive Drive Carrier Figure D-10 Installing a Hard Drive SAS/SATA or Scsi Hard Drive Drive Tray Connecting Cables to the Mobile Rack Removing the Exhaust Fan and Connecting SAS/SATA Cables Figure D-12 Removing Mobile Rack Fan Figure D-13 Removing Mobile Rack Fan Additional Optional Installation Information Backplane Screw Locations Appendix E SAS-743TQ Backplane Specifications An Important Note to Users Introduction to the SAS-743TQ Backplane Front Connectors Figure E-1 Front Connectors Front Connector and Pin Definitions #1. and 2. Jtag Connector and Upgrade Connectors#4. Backplane Main Power Connectors #3. MG9072 Chip #6. and #7. Sideband Headers #8. and #9. I2C Connectors#10. #17. SAS Ports JP41 JP34 Connector Pins Jumper Setting I2C and Sgpio Mode Jumper Settings SAS Port Connections in I2C and Sgpio Settings State Specification Front LED IndicatorsOH/Drive Fail LED J15 SAS Drive Number Appendix F SATA-743 Backplane Specifications Introduction to the SATA-743 Backplane Connectors and Jumpers Figure F-1 Front Connectors Front Connector and Jumper Pin Definitions JP25 Explanation of JumpersJP18 MM2 Front LED Indicator Normal State Indicator Status Rear Connectors Figure F-4 Rear Connectors Rear Sata Connectors Rear LEDs Appendix F SATA-743 Backplane Specifications