5 - Basic operations
34
TASC AM D A-78H R
5Press the
CLEAR (PRE ROLL) key on ce more
so th at the displ ay show s PO 0003 (PO0003),
i.e. the post-roll time.
Since there is little point in setting pre- and post-roll
times to frame accuracy, you can only set these val-
ues to second accuracy.
The minimum values you can set are 5 seconds (pre-
roll) and 3 seconds (post-roll) and the maximum
value i s 59 minut es 59 sec onds for both.
Any punch operation from now will take your setting
for pre-roll and use it when locating the tape to the
punch-in point. For example, if your pre-roll time has
been set to 10 seconds (00:00:10.00), and the punch-
in point is at 00:06:03.12, the tape will locate to
00:05 :53.12 when sta r t i ng reh e ars a l or pu nc h -i n .
5.6.5 Rehearsi ng the pu nch-in
After you have set the punch points, and you have
located the tape to the pre-roll point, as described
above, you can rehearse the punch process.
1Press the
RHSL key so that the indicator lights
steadily.
This indicates that you are now in rehearsal
mode.
2Press PLAY
. The tape will start playing from
the pre-roll point.
3At the punch-in point, monitoring will cha nge
to source.
The RECORD key will flash, and the REC
FUNCTION indicator of any armed tracks will
light steadily. However, recording will not be
carried out.
4At the punch-out point, monitoring will chan ge
back to off-tape monitoring.
The tape will continue playing to the post-roll
point and then rewind to the pre-roll point.
5Repeat the rehearsal process until you are sat-
isfied with the performance.
5.6.6 Interrupting a rehearsal or punch recording
Very often while rehearsing a punch-in, you will not
want to run the tape all the way to the punch-out
point (an entry cue is missed, or a mistake is made
early on in the take). In these cases, the following
procedure applies to both rehearsal and punch
recording:
1While the tape is running, press the LOC 1 key
(there is no need to press STOP first).
The tape will return to the punch-in point,
minus the value specified in the punch-in offset
(5.6.4, “Editing the pre-roll and post-roll
times ”).
2Pressing PLAY will then re-start the rehearsal
or punch-in process.
• Pre ssin g the LOC 2 key will locate th e tape to the
punch-out position minus the punch-in pre-roll
time.
• These functions are only operative when the RHSL
or AUTO IN/OUT indicators are lit or flashing.
When they are off, the LOC 1 and LOC 2 keys will
act normally.
5.6.7 R ecording the punch- in
1Make sure the tape is at the pre-roll point, and
press the AUTO IN/OUT key once.
The indicator will flash, showing that the DA-
78HR is in auto-punch mode.
2Press PLAY
. The tape will start playing.
At the punch-in point, the RECORD indicator
will light steadily, as will the REC FUNCTION
indicators of a ny armed tracks . Monitoring
will change from off-tape to source and the
INPU T MO NITOR of any armed tracks will
light.
Recording will now actually take place. Any
recorded material which was previous ly on the
armed tracks between the punch points will be
replaced by the new recording.
3At the punch-out point, the monitoring will go
back to off-tape (the INPUT MONITOR indica-
tors of armed tracks will go out), and when the
post-roll point is reached, the tape will rewind
to the pre-roll point.
4The AUTO IN/OUT indicator will light steadily,
showing that the DA-78HR is now in replay
mode.
5.6.8 R eplaying the punche d materia l
1To replay the punch-in, press the PLAY key.
Playback will start (the REC FUNCTION indi-
cators of the armed tracks will continue to
flash ).
2At the post-roll point, the tape will automati-
cally rewind to the pre-roll point.