Time value to | Tascam RC-898 specification

10.1 - Menu groups

Menu group 3

M c n O f f s e t C t r l P r t

T

i m e M o d e

T r k A r m

R

e

p e a t

Menu item

Parameter(s)

Values

Reference

Machine Offset

Time value to

+02:00:00:00

7.2.3, “Chasing with

frame accuracy

an offset”

Time Mode

Time reference

88 98

ABS or TC

6.4.2, “Selecting

Time Mode”

Control Proto-

Type

98

9Pin, MIDI, Bus, off

9.4.1, “Choosing a

col

control protocol”

Remote Track

Enabled

98

enable, disable

9.4.4, “Remote track

Arming

arming”

Repeat Start/

Start or end

Any valid time entries

6.6, “Repeating a

End

Time values to

section”

frame accuracy

Menu group 4

T c C h s R e c T C O f f s e t

R

e c h s M o d e P a r k P o s i

E

r

r B y P a s s

Menu item

Parameter(s)

Values

Reference

TC Chase Indiv.

Enabled or dis-

98

enabled, disabled

8.2.9, “Individual

Rec.

abled for each

recording status

DTRS unit

while chasing time-

code”

Rechase Mode

Mode

98

rechase, free

8.2.5, “Rechase

Window

1 sec, 2 sec

mode”

Error Bypass

Time in frames

88 98

10 frame, 30 frame

8.2.4, “Error bypass”

Timecode Offset

Time value to

88 98

Any valid time value in the range

8.1.9, “Chasing with

subframe

±12:00:00:00.00

a timecode offset.”

accuracy

Park Position

Test

98

off, on

8.2.8, “Park posi-

Manual entry to

00s00f through 2 seconds minus 1 frame

tion”

frame accuracy

10-3

Image 67

Tascam RC-898 owner manual Time value to

Contents

RC-898 For U.S.A Menu and basic operations Table of Contents IntroductionRC-898 features Connections Menu and parameter reference Table of Contents Making settings on the Dtrs unitsExternal control and settings Timecode functions Unpacking Key featuresKey features Introduction Digital audio cables Precautions and recommendationsPrecautions and recommendations Battery backup Accessories AccessoriesReference clock in a digital studio Accessories RC-898 features Front panel Time Mode indicators Machine number indicators Through 6, E1, E2Lock Status indicators Vari indicators Front panel ENTER/LOAD key Preset keyData INC/DEC key and indicator Repeat key and indicator Rear Panel Contrast Rear Panel DIP switches 1 Machine IDs ConnectionsConnection to Dtrs units Connection to Dtrs units Connections GPI event units Connections parallel unitsConnections RS-422 Units Connections parallel units Memory and batteries Memory and batteries Memory and batteries Invalid operations Menu and basic operationsNavigation Navigation Data entry Resetting values to zeroFast setting of values Setting values using the Value display Commonly-used menus Selecting the unit controlled by the menus Saving the current setup Storing and recalling user setupsStoring and recalling user setups Recalling menus using the function keys Recalling a user setup or restoring factory settings Storing and recalling user setups Formatting tapes Basic Dtrs operationsTransport controls Selecting the unit to which operations refer Arming tracks Shuttle modeMonitoring Monitoring Shuttle muting Shuttle monitoring Monitoring Monitoring flowchart DA-88 and DA-38 Monitoring Monitoring tables Monitoring Reference modes Setting the precisionSetting a relative time reference Location functions Return-to-zero ABS settingABS setting Selecting Time Mode Auto play Setting the location pre-roll valueLocation operations Location operations Recalling a location memory Manual entry of a location pointEditing a location Storing the location in a memory Editing a location memory Repeating a sectionRepeating a section Repeated entry of location points Punch operations Rehearsing the punch recording Setting pre-roll and post-roll timesCrossfade times Performing the punch recording Punch operations Track operations Making settings on the Dtrs unitsTrack delay Track operations Rec Mute function Key ModeUnit-related functions Unit-related functions Auto Offset function Chasing with an offset From menu group E, move the cursor to either Checking the offsetClock selection Output timing Dither Varispeed pitch controlInput selection Word length Sine oscillator Unit-related functions Confidence modeReference levels Meter modes N e O s c i l l a t o r C h i n e Unit-related functions Selecting the timecode source Timecode functionsPrimary timecode functions Primary timecode functions Selecting a timecode type Setting the generator start time Start the timecode source Checking the generator progressRecording the timecode on a Dtrs timecode track Rewind the tape to the beginning Chasing with a timecode offset Chasing to external timecode Auto Timecode Offset function Independent clock settingsAdvanced timecode functions Advanced timecode functions Pull up and pull down Error bypassRechase mode Synchronization of timecode Midi Timecode output Fast LTCPark position Video resolve Individual recording status while chasing timecodePlay the master unit D e o R e s o l v e C h i n e O f f E e Advanced timecode functions Controlling the parallel port device External control and settingsControlling GPI devices Location pre-roll on the serial unit Controlling the serial port 9-pinControlling the serial port 9-pin Selecting the serial port device Use the UP and Down keys to select between Split and Normal Split mode on the serial unitSerial unit timing source Controlling recording operations on the serial unit Track mapping functions Other Dtrs control functionsOther Dtrs control functions Choosing a control protocol Device emulation Recording delayTimecode track mapping Remote track arming Cue-up tally Fast wind speedMMC ID D I / B u s I D C h i n e C e i v e Other Dtrs control functions Menu groups Menu and parameter reference Menu groupsMenu group GPI Time value to Timecode type Output All parameters On, off 7, Midi Time Fast wind mode Menu group E Menu group a Menu group F Alphabetical list of menu items Alphabetical list of menu items Dimensions SpecificationsSpecifications Dimensions Dtrs Index A-E ABS 6-2,8-2 Index F-O Index P-T Generator 8-1,8-2,10-5,10-6 Index U-Z RC-898