The third screen shows the right side (R) of the freezer.
The top line of these screens shows the hopper (H) and barrel (B) temperatures recorded at the end of the Heat Treat Cycle and indicates the side (L or R) of the freezer.
The remaining lines indicate the following:
HEAT = Total time for the hopper (h) and barrel (b) to reach 150.9°F (66.1°C).
OVER = Total time the hopper (h) and barrel (b) temperature was above 150°F (65.6°C).
COOL = Total time the hopper (h) and barrel (b) temperature was above 41°F (5°C) during the COOL phase.
PEAK = Highest temperature reading for the hopper
(h) and barrel (b) during the Heat Treatment Cycle.
H: 40.9 |
| B:26.3 | L | |
HEAT | OVER |
| COOL | PEAK |
1:12 | 0:49 | h | 1:19 | 161.0 |
0:46 | 1:11 | b | 0:15 | 169.7 |
|
|
|
| |
|
|
|
| |
H: 38.0 |
| B:23.7 | R | |
HEAT | OVER |
| COOL | PEAK |
1:09 | 0:52 | h | 1:11 | 161.2 |
0:66 | 1:00 | b | 0:11 | 169.9 |
|
|
|
|
|
The HEAT time indicates the amount of time taken in each zone to reach 150.9°F (66.1°C). Each zone must remain above 150°F (65.6°C) for a minimum of 35 minutes.
Touch the UP arrow symbol to advance to the next page or the DOWN arrow symbol to view the previous page. A Heat Cycle Failure message will display on the first screen if a failure occurred.
Listed below are variable failure code messages which could appear on line 2.
HT | HEAT TIME FAILURE |
| Mix temperature did not rise above 151_F |
| (66.1_C) in less than 90 minutes. |
CL | COOL MODE FAILURE |
| Mix temperature in the hopper and freezing |
| cylinder did not fall below 41_F (5_C) in less |
| than 90 minutes for UVC3 units or 120 |
| minutes for UVC4 units. |
TTTOTAL TIME FAILURE
The heat treatment cycle must be completed in no more than 4 hours.
ML | MIX LOW FAILURE |
| The Heat Phase or Cool Phase time was |
| exceeded and a mix low condition was |
| present. |
MO | MIX OUT FAILURE |
| A mix out condition was detected at the start |
| or during the heat cycle. |
BO | BEATER OLVD IN HC |
| A beater overload occurred during the heat |
| cycle. |
HO | HPCO IN HEAT CYCLE |
| A high pressure |
| during the heat cycle. |
PF | POWER FAILURE IN HC |
| A power failure caused the Heat Phase, |
| Cool Phase, or Total Cycle Time to exceed |
| the maximum allowed time. If a power failure |
| occurs, but the heat treatment cycle does |
| not fail, an asterisk(*) will appear on the third |
| line of the display. |
OP | OPERATOR INTERRUPT |
| Indicates the heat cycle was aborted in the |
| OPERATOR INTERRUPT option in the |
| Service Menu. |
PS | POWER SWITCH OFF |
| The power switch was placed into the OFF |
| position during the heat cycle. |
TH | THERMISTOR FAILURE |
| A thermistor probe has failed. |
PD | PRODUCT DOOR OFF |
| A product door is not in place or is loose. |
140303
Models C709 & C717 | 29 | Important: To the Operator |
|
|
|
