Water Connections

(Water Cooled Units Only)

An adequate cold water supply must be provided with a hand shut-off valve. On the underside of the base pan or on the right side, two 3/8” I.P.S. water connections for inlet and outlet are provided for easy hook-up. 1/2” inside diameter water lines should be connected to the machine. (Flexible lines are recommended, if local codes permit.) Depending on local water conditions, it may be advisable to install a water strainer to prevent foreign substances from clogging the automatic water valve. There will be only one water “in” and one water “out” connection. DO NOT install a hand shut-off valve on the water “out” line! Water should always flow in this order: first, through the automatic water valve; second, through the condenser; and third, through the outlet fitting to an open trap drain.

A back flow prevention device is required on the incoming water connection side. Please refer to the applicable National, State, and local codes for determining the proper configuration.

Electrical Connections

In the United States, this equipment is intended to be installed in accordance with the National Electrical Code (NEC), ANSI/NFPA 70-1987. The purpose of the NEC code is the practical safeguarding of persons and property from hazards arising from the use of electricity. This code contains provisions considered necessary for safety. Compliance therewith and proper maintenance will result in an installation essentially free from hazard!

In all other areas of the world, equipment should be installed in accordance with the existing local codes. Please contact your local authorities.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

Each unit requires one power supply for each data label on the unit. Check the data label(s) on the freezer for branch circuit overcurrent protection or fuse, circuit ampacity, and other electrical specifications. Refer to the wiring diagram provided

130225

inside of the electrical box for proper power connections.

CAUTION: THIS EQUIPMENT MUST BE PROPERLY GROUNDED! FAILURE TO DO SO CAN RESULT IN SEVERE PERSONAL INJURY FROM ELECTRICAL SHOCK!

This unit is provided with an equipotential grounding lug that is to be properly attached to the rear of the frame by the authorized installer. The installation location is marked by the equipotential bonding symbol (5021 of IEC 60417-1) on both the removable panel and the equipment's frame.

SStationary appliances which are not equipped with a power cord and a plug or another device to disconnect the appliance from the power source must have an all-pole disconnecting device with a contact gap of at least 3 mm installed in the external installation.

SAppliances that are permanently connected to fixed wiring and for which leakage currents may exceed 10 mA, particularly when disconnected or not used for long periods, or during initial installation, shall have protective devices such as a GFI, to protect against the leakage of current, installed by the authorized personnel to the local codes.

SSupply cords used with this unit shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or other equivalent synthetic elastomer-sheathed cord (Code designation 60245 IEC 57) installed with the proper cord anchorage to relieve conductors from strain, including twisting, at the terminals and protect the insulation of the conductors from abrasion.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified person, in order to avoid a hazard.

To the Installer

2

Models C709 & C717

 

 

 

Page 5 Page 7
Page 6
Image 6
Taylor manual Water Connections, Electrical Connections, Water Cooled Units Only, To the Installer Models C709 & C717
Page 5 Page 7

C717, C709 specifications

Taylor C709 and C717 are two outstanding models from the renowned Taylor Guitars, each designed to cater to the discerning tastes of musicians looking for exceptional playability, sound quality, and craftsmanship.

The Taylor C709 is known for its remarkable tonal balance and projection. Constructed with a solid Sitka spruce top, it delivers a bright, clear sound that enhances the overall musicality of the instrument. The back and sides of the C709 are crafted from layered sapele, which not only adds to the visual appeal but also contributes to a warm, resonant voice. This model features a Grand Symphony body shape, known for producing a rich, full sound, making it an excellent choice for strumming and fingerpicking alike.

On the other hand, the Taylor C717 takes things a notch further with its unique design and features. It also boasts a solid Sitka spruce top, but pairs it with solid sapele back and sides, offering a more vibrant and dynamic tonal range. The Grand Pacific body shape of the C717 is specifically engineered for a vintage-inspired sound, making it perfect for players seeking warmth and depth. This model is designed to provide a pleasing balance between bass, midrange, and treble frequencies, ensuring a versatile performance suited for various styles.

Both models are equipped with the Taylor Expression System 2, a technologically advanced pickup system designed to capture the natural acoustics of the guitar. This feature makes it easier for musicians to amplify their sound without compromising the instrument's organic tone.

In terms of playability, both the C709 and C717 are built with a smooth mahogany neck and an ebony fingerboard, which provides a comfortable playing surface for intricate fingerwork and chords. The action is set to make playing effortless, whether you're a beginner or an experienced musician.

Aesthetically, Taylor has ensured that these guitars are as visually striking as they are sonically impressive. The glossy finish, elegant inlays, and overall craftsmanship make them showpieces worthy of attention on stage or in a personal collection.

In conclusion, the Taylor C709 and C717 models represent the perfect blend of innovation, tradition, and artistry, making them coveted instruments for players at all levels. With their superior tone, excellent playability, and stunning design, these guitars continue to uphold Taylor’s legacy of quality and excellence in the world of acoustic instruments.
Top Page Image Contents