Lift Cylinder Repair No and 3 Left and Right Fig | Toro 3100

Lift Cylinder Repair – No. 2 and 3 (Left and Right) (Fig. 35)

Figure 35

IMPORTANT: To prevent damage when clamping the cylinder barrel in a vise, clamp only on the pivot end. Do not clamp the vise jaws against the smooth shaft surface. Protect the shaft surface before mounting in the vise.

1.After removing the cylinder, pump the oil out of the cylinder into a drain pan by SLOWLY moving the cylin- der’s piston in and out of the cylinder bore.

2.Plug the ports and clean the outside of the cylinder.

3.Mount the cylinder in a vise so the shaft end of the cylinder is tilted up slightly. Do not close the vise so firmly that the barrel could become distorted.

4.Remove the retaining ring (Item 10). Grasp clevis (Item 13) at end of shaft and use a twisting and pulling motion to carefully extract piston (Item 3), shaft (Item 6), and head (Item 9) from the barrel (Item 1).

5.Securely mount the shaft (Item 6) in a vise and remove the lock nut (Item 2) from the piston end of the shaft. Remove the piston (Item 3). Slide the head (Item 9) off of the shaft.

6.Remove and discard all seals and back-up rings (Items 4, 5, 12, 7, 8, 11).

7.Wash the parts in a safe solvent. Dry the parts with compressed air. DO NOT wipe them dry with a cloth or paper as lint and dirt may remain.

8.Inspect the internal surface of the barrel for damage (deep scratches, out-of-round, etc.). Inspect the head, shaft and piston for evidence of excessive scoring, pitting, or wear. Replace any defective parts.

9.Put a light coating of hydraulic oil on all new seals and back-up washers. Install the new seals and back-up washers (Items 4, 5, 12, 7, 8, 11). Install the head (Item 9) onto the shaft (Item 6). Install the piston (Item 3) onto the shaft and tighten the lock nut (Item 2).

10.Put a light coating of hydraulic oil on all cylinder parts to ease assembly. Slide the piston, shaft and head into the barrel. Install the retaining ring (Item 10) to secure the assembly in the barrel.

Greensmaster® 3100

Page 4 - 53

Repairs

Image 81

Toro 3100 manual Lift Cylinder Repair No and 3 Left and Right Fig

Contents

Preface Greensmaster 3100/3050 This page is intentionally blank Table Of Contents This page is intentionally blank Safety Instructions Safety InstructionsChapter Before Operating While Operating Safety Instructions Greensmaster Safety Instructions Safety Instructions Greensmaster 2 1 Rev.. DB Product Records Product Records Decimal and Millimeter Equivalents Equivalents and ConversionsTo Metric Conversions Equivalents and Conversions Greensmaster Torque Specifications Torque SpecificationsCapscrew Markings and Torque Values U.S. Customary Capscrew Markings and Torque Values Metric This page is intentionally blank Specifications Specification3 1 Rev. D Specifications Throttle Control Adjustment Fig AdjustmentsChoke Control Adjustment Fig Adjustments Greensmaster Governor Lever Adjustment Fig Governor Adjustment Before starting engineThrottle Restrictor Adjustment Fig Secondary Spring Adjustments Fig Warnin G Carburetor and Speed Control Adjustment Engine Removal and Installation Installing the EngineRemoving the Engine Engine Removal and Installation Greensmaster Hydraulic System Table of Contents Description Specifications 4 2 Rev. D General Information Hydraulic Fitting InstallationHydraulic Hoses Ring Face Seal SAE Straight Thread O-Ring Port Non-adjustable Fig SAE Straight Thread O-Ring Port AdjustableGeneral Information Greensmaster Traction, No Position Hydraulic Flow Diagrams Hydraulic Flow Diagrams Greensmaster Traction, Reverse Position Reel Drive, Mowing Operation Hydraulic Flow Diagrams 4 8 Rev. E Greensmaster3100 4 9 Rev. E Reel Drive, Lower Cutting Units Reel Drive, Raising Cutting Units Hydraulic Flow Diagrams 4 10 Rev. E 4 11 Rev. E Power Steering, R.H. Turn Greensmaster Hydraulic Schematics Hydraulic Schematic Greensmaster 3100 2WD Serial Rev. E Hydraulic Schematics 4 12.2 Rev. E Hydraulic Schematic Greensmaster 3100 3WD 12.3 Hydraulic Schematic Hydraulic Schematics 4 12.4 Rev. E Greensmaster Hydraulic Tester Fig Special Tools Detent Installation Tool Fig Seal Protector FigSpecial Tools Greensmaster Seal Installation Tool Fig Assembly Studs FigControl Valve Spool Seal Installation Tools Fig Troubleshooting Greensmaster Troubleshooting Slow Groundspeed in All Traction Selections Troubleshooting Slow or No Ground Speed in No and Reverse No Appears Normal No Increase in Speed from No to No One or More Cutting Units Slow or No Reel Drive Action All Reels Slow or Will Not Turn Mow Pedal Won’t Stay Engaged Reels Slow Down or Stop Cutting Units Drop During Transport Cutting Units Lift Too Slowly or Not At All Center #1 Cutting Unit Operates in Raised Position Lift Pedal Binding Steering Loss, Steering Wander or Free Play Testing Testing Traction Pump Flow Traction Relief Setting Engine when the traction lever is engagedTesting Greensmaster Test Hook UP no Test B Relief Valve Setting Procedure Test Hook UP NO.2 4 30 Rev. E Testing Test Hook UP NO.2 Testing 4 31 Rev. E Greensmaster Engine when the mow pedal is engaged Testing 4 32 Rev. E Greensmaster3100Reel Drive Pump Efficiency 4 33 Rev. E Testing Test a Reel Drive Motor Flow Procedure Test Hook UP no 4 35 Rev. E Testing Test Hook UP no GreensmasterSteering Pump Flow and Relief Pressure Lift and Mow Pedal Height Adjustment Fig 4 37 Rev. B Adjustments Traction Pedal Adjustment FigTraction Return Linkage a Reverse Rear Camshaft Adjustment Fig Reel Motor Shaft Seal Replacement Fig Reel Motor Removal and Installation FigRepairs Repairs Repairs 4 40 Rev. B Reel Motor 70-9800 Repair Fig Repairs Repairs 4 41.1 Rev. B Greensmaster Reel Motor 94-3506 Repair a Greensmaster 4-41.2 Rev. B Repairs Disassembly Reel Motor 105-9770 Repair bRepairs 4 41.3 Rev. D Greensmaster Greensmaster 4-41.4 Rev. D Repairs Inspection Repairs 4 41.5 Rev. D Greensmaster Reassembly This page is intentionally blank Repairs Greensmaster Pump Repair Greensmaster 3100 shown Fig Relief Valve Service Repairs Greensmaster Control Valve Removal and Installation Fig Relief Valve Removal and Installation FigGreensmaster Repairs Rear Bonnet Side Fig Control Valve Spool Seal Replacement Control Valve Internal Seal Replacement Fig Control Valve No Spool Detent Replacement Reassemble With the Following Procedures Control Valve No Spool Detent Replacement Fig No Center Lift Cylinder Fig Lift Cylinder Removal and Installation No and 3 Lift Cylinders Fig Lift Cylinder Repair No Center Fig Lift Cylinder Repair No and 3 Left and Right Fig Wheel Motor Removal and Installation Fig Wheel Motor Repair Disassembly of Motor Fig Before Assembling Motor Assembly of Motor Rotor, Stator and Vane Assembly Reverse steps 1 3 to install the steering cylinder Steering Cylinder Repair Greensmaster 3100 Fig Repairs Greensmaster Steering Control Unit Repair Greensmaster 3100 Fig Meter Gerotor End Disassembly Control End Disassembly Push pin from spool and sleeve assembly Repairs Control End Reassembly Repairs Repairs Greensmaster Repairs Repairs Greensmaster Repairs Repairs Greensmaster Electrical System Wiring Schematics 5 2 Rev. D Greensmaster Wiring Schematic Greensmaster 3100, S/N Below Wiring Schematic Greensmaster 3100, S/N 80001 Wiring Schematics5 2.1 Rev. D Greensmaster 3100, S/N Wiring Schematic220999999 5 2.2 Rev. D Wiring Schematic Wiring Schematics 5 2.4 Rev. D Greensmaster 3100/3050 Wiring Schematic Greensmaster 3050, S/N Below 5 2.5 Rev. D Wiring Schematics Wiring Schematic Greensmaster 3050, S/N 80001 Wiring Schematics 5 2.6 Rev. D Wiring Schematic Greensmaster 3050, S/N 230000001 and Up 200999999 3100/3050 This page is intentionally blank Before Start-Up Cold Oil Normal Operation Warm OilLeak Alert Volt Ohm Amp Meter Fig Continuity Tester Fig Skin-Over Grease Fig Condition Cause Correction Problem Cause Correction Verify Interlock Operation Ignition Key Switch Fig Traction Neutral Switch Fig Seat Switch Fig Interlock Module Fig Mow/Lift Switch Fig Battery HourmeterTurf Guardian TM Leak Detector System Seat Switch Replacement and Adjustment Fig General Safety Interlock Switch Service Traction Neutral Switch Replacement and Adjustment Fig Wiring Harness Service Mow/Lift Switch Replacement and Adjustment Fig Battery Specifications Battery Service 6 1 Rev. B Wheels, Steering and Brakes Specifications Greensmaster Brake Adjustment Fig Brake Disassembly Reassembly Brake Service Fig Steering Arm Greensmaster Steering Cable Greensmaster6 5 Rev. B Repairs Repairs 6 6 Rev. B Greensmaster Bolt Adjust Cutting Units Page Page Page Page Page Page Use Loctite 271 on spline nut Rev. C Page Page Page Page Page Page Page Page Page Page Use Loctite 271 on spline nut Rev. C Page Single Point Adjust Cutting Units Page Page Page Page Page Page Page Page Use Loctite 271 on spline nut threads Rev. C Page Page Page Page Page Page Page Page Page Page Page Page Page Use Loctite 271 on spline nut threads Rev. C Page Page For Four Bolt Adjust and Single Point Adjust Cutting Units Introduction9 1 Rev. D Introduction Page Page Page Page Page Page Page Page Page Page Use Loctite 271 on spline nut threads Rev. C Page Page Page Page Page Page Page Page Page Page Page Page Page Page Use Loctite 271 on spline nut threads Rev. C Page Page Page Page Page Page This page is intentionally blank 10 1 Rev. D Dual Point Adjust Cutting units Dual Point Adjust Cutting Units Weight Dual Point Adjust Cutting Units 10 2 Rev. DMaximum Reel Speed 2200 RPM Backlapping Brush Assembly Gauge Bar Assembly10 3 Rev. D Dual Point Adjust Cutting units Bedknife Screw Tool Dual Point Adjust Cutting Units 10 4 Rev. D Greensmaster Inner Grease Seal Installation WasherPlastic Plug Turf Evaluator Tool After installation to the bedbar Factor Possible Problem/Correction10 5 Rev. D Dual Point Adjust Cutting units Factors That Can Affect Quality of Cut Dual Point Adjust Cutting Units 10 6 Rev. D Greensmaster Set Up and Adjustments Characteristics10 7 Rev. D Dual Point Adjust Cutting units Dual Point Adjust Cutting Units 10 8 Rev. D Greensmaster InstallationHydraulic Reel Motor Removal To Avoid Personal Injury or Death 10 9 Rev. D Dual Point Adjust Cutting units Dual Point Adjust Cutting Units 10 10 Rev. D Greensmaster Bedbar Assembly Installation Fig Bedbar Removal and Installation10 11 Rev. D Dual Point Adjust Cutting units Removal Fig Dual Point Adjust Cutting Units 10 12 Rev. D Greensmaster Bedbar Adjuster Service Replacement Bedknife Replacement and Grinding10 13 Rev. D Dual Point Adjust Cutting units Grinding Dual Point Adjust Cutting Units 10 14 Rev. D Greensmaster Reel Assembly Reel Removal Fig 10 15 Rev. D Dual Point Adjust Cutting units Left Side Plate Service Fig Right Side Plate Service FigDual Point Adjust Cutting Units 10 16 Rev. D Greensmaster 10 17 Rev. D Dual Point Adjust Cutting units Reel Service Fig Dual Point Adjust Cutting Units 10 18 Rev. D Greensmaster Reel Installation Fig Preparing a Reel for Grinding 10 19 Rev. D Dual Point Adjust Cutting units Dual Point Adjust Cutting Units 10 20 Rev. D Greensmaster Front Roller Removal and Installation Seal Installation Front and Rear Roller Service10 21 Rev. D Dual Point Adjust Cutting units Seal Removal Bearing Installation Dual Point Adjust Cutting Units 10 22 Rev. D GreensmasterBearing Removal This page is intentionally blank Commercial Products