Manuals / Brands / Computer Equipment / Projector / Toshiba / Computer Equipment / Projector

Toshiba TLP-ET1B, TLP-ET1E, TLP-ET1U the Status display menu icon [ ].

1 50

Download 50 pages, 4.39 Mb

36

Operations

Notes

•Items can be displayed (marked with “Yes”) or cannot (marked with “–”) depending on each type of input.

•Pressing the EXIT button on the remote control dismisses the menu screen.

Item Description

Video S-video Y/PB/PRAV Computer

Input Displays the input source name. Yes Yes Yes Yes Yes

Mode name Displays the RGB signal mode name.*1––––Ye s

H-resolution Displays the horizontal resolution (in dots). ––––Yes

V-resolution Displays the vertical resolution (in dots). ––––Ye s

H-frequency Displays the horizontal sync frequency. ––––Yes

V-frequency Displays the vertical sync frequency.*2––––Yes

Sync Displays the sync signal polarity.*3––––Yes

Signal format Displays the Y/PB/PR signal format. ––Ye s ––

Video mode Displays the video signal color system. Yes Yes –Yes –

Lamp time Displays the total time of lamp use.*4Yes Ye s Yes Yes Yes

Version Displays the firmware version.*5Yes Ye s Yes Yes Yes

Using the menus (Continued)

Press the MENU button.

Use the and buttons to select

the Status display menu icon [ ].

The “Status display” menu will appear.

Status display menu

This menu displays information about the input signal, lamp use time, etc.

e.g.

Remote control

Control panel

Menu

Status display

Exit

Input

Mode name

H-resolution

V-resolution

H-frequency

V-frequency

Sync

Lamp time

Version

*1: The mode of supported RGB signals ( p.48) is shown.

*2: Same as the refresh rate of the computer signal.

*3: Sync signal polarity shown as P (positive) or N (negative) for “H/V”.

*4: Display “Lamp time” as a measure of when the lamp should be replaced. (Cannot be used as a counter of

guaranteed lamp time.)

*5:“Version” shows the version of the projector’s internal control program. This version is referred for customer

service, etc.

Contents

Main SAFETY PRECAUTIONS Wash hands after handling IMPORTANT SAFETY INSTRUCTIONS 1. Read Owner's Manual 2. Power Sources 3. Source of Light 4. Ventilation Page 15. Accessories 16. Damage Requiring Service 18. Servicing 19. Replacement Parts 20. Safety Check LABEL LOCATIONS IMPORTANT PRECAUTIONS Save Original Packing Materials EXEMPTION CLAUSES Moisture Condensation Place and Manner of Installation OTHER CAUTIONS AND INFORMATIONS Copyrights Disposal Trademarks Notational Conventions Used in This Manual CONTENTS Before Using Preparations Operations Maintenance Parts of the main unit Parts on the control panel and remote control Control panel Remote control (1) (4) (2) (3) (5) (6) (7) Connection terminals Preparing and using the remote control Loading batteries into the remote control Put back the battery cover. Remove the battery cover. Insert dry cell batteries. Placing the projector Determine the placement style. Determine the projection distance and place the unit. Connecting an input source device Connecting a video device Preparations Connecting a computer Connecting a DVD player with component video terminals Connecting an input source device (Continued) Connect the power cord. TEMP FANLAMPON Turning the power on and off Before turning the power on LCD Panels Turning the power on Press the ON/STANDBY button. Safety lock TEMP FANLAMPON Turning the power off PRECAUTIONS Press the ON/STANDBY button again. FANTEMPLAMPON FANTEMPLAMPON Turn on the power. Adjust the projection angle. Projecting Place the connected device in operating status. Select the connected input. P (Using the remote control) Press an INPUT button (VIDEO/S, YP / AV, or COMPUTER) to select the input. Easy setup using the EASY button Correction of keystone distortion Press the ( ) button. Changing the projection size Press the SIZE button on the remote control. Changing the screen size Cutting off the sound/Pausing the picture Cutting off the sound temporarily (Mute) Press the MUTE button on the remote control. Cutting off both the picture and sound temporarily (Sleep) Press the SLEEP button on the remote control. Switching the picture and sound Setting the picture mode Press a PICTURE MODE button (STD./CINEMA/ GAME) on the remote control. Enlarging the picture (Zoom) Press the USER button. Calling up a user profile Using the menus Use the and buttons to select a desired menu icon, then press the button. How to use the menus Press the OK button if an adjustment bar or selection items did not displayed on the Step 3 . to set the item. Press the OK button. Use the and buttons to select a desired adjustment or setting item. the picture adjustment menu icon [], then press the button. item you want to adjust, then adjust it Picture adjustment menu Page the audio adjustment menu icon [ ], then press the button. item you want to adjust, then adjust it Audio adjustment menu Use the and buttons to select the default setting menu icon [ ], then press the button. item you want to set, then set it Pressing the EXIT button on the remote control dismisses the menu screen. Default setting menu Use this menu to make settings such as the placement style (projection mode). e.g. the Status display menu icon [ ]. Status display menu User memory menu Use the or button to select the user memory menu icon [ ]. Press the button. Press the button, move the cursor to the user memory registration name, then press the OK button. OK Use the , , , and buttons to select each character you want to enter, then press the OK button. When you finish entering characters, use the , , , and buttons to select , then press the OK button. Removing the tilt stand Air filter cleaning Unplug the power cord. Remove the air filter. Clean the filter. Replace the air filter. Lens and main unit cleaning Lens cleaning Main unit cleaning Replacing air intake and exhaust fans, and air filter Unplug the power cord. Wait until the lamp is sufficiently cooled. Lamp replacement Lamp replacement messages Remove the lamp cover. Pull out the lamp. Mount the new lamp. Replace the lamp cover. Replace the tilt stand. Reset the lamp timer. qTurn on the power of this unit. wPress the MENU button. PRECAUTIONS Used lamps Trouble indications No power Lamp went out during use Power went out during use, or wont come on Power went out during use Before calling service personnel Specifications List of general specifications Connection terminals List of supported signals List of supported signals (RGB signals) Pin assignment of COMPUTER terminal Replacement lamp Model TLPLET1 Designs and specifications are subject to change without notice for improvements. Separately sold product List of supported signals (Y/PB/PR signals)