Worth Data 802 RF */A/* */B/*, */C/*, */%/*, */5/*

O-1

802 RF Terminal Setup Menu

To change a setting using the 802 RF Terminal Setup Menu:

• Scan START SETUPto enter setup mode

• Scan the parameter you want to change (i.e. Code 3 of 9)

• Choose the setting you want to change and scan the corresponding letter

or

number from the Barpad Table (0-9, A-F)

• When all changes have been made, scan END SETUP

•* indicates default settings

Start Setup End Setup

*/+/* */-/*

Code 3 of 9 UPC/EAN

*/A/* */B/*

0 Enable Code 39

1 Disable Code 39

2 Enable Full ASCII Code 39

3 Disable Full ASCII Code 39

4 Enable Accumulate Mode

5 Disable Accumulate Mode

6 Transmit Start/Stop characters

7 Don’t transmit Start/Stop characters

8 Enable Mod 43 Check Character

9 Disable Mod 43 Check Character

ATransmit Mod 43 Check Character

B Don’t transmit Mod 43 Check Character

C Caps Lock ON

DCaps Lock OFF

0 Enable UPC/EAN

1 Disable UPC/EAN

2 Enable Supplements

3 Disable Supplements

4 Transmit UPC-A NSC

5 Don’t transmit UPC-A NSC

6 Transmit UPC-A Check Digit

7 Don’t transmit UPC-A Check Digit

8 Transmit UPC-E NSC & EAN-8 Flag Ch

9 Don’t transmit UPC-E NSC & EAN-8 Flag Ch

ATransmit UPC-E & EAN-8 Check digit

B Don’t transmit UPC-E & EAN-8 Check digit

CUPC-E Compressed transmission

DUPC-E Expanded transmission

E EAN-8 observes 9 & A above

F EAN-8 is forced to transmit 8 digits always

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

2 of 5 Code 2 of 5 Length

*/C/*

0 Enable I 2 of 5

1 Disable I 2 of 5

2 Enable check digit

3 Disable check digit

4 Transmit check digit

5 Don’t transmit check digit

6 Enable 2 of 5

7 Disable 2 of 5

*

*

*

*

*/5/*

Scan 2 digit length (default is 06)

RSS-14

0 Disable RSS-14 2 14 + Identifiers

1 Standard 14 digits 3 14 + UCC-128 Emulation

*/%/*

Appendix O

Contents

Main Table of Contents Page Chapter 1 Installation Components Installation Tips Page Battery Life Indicator To change the AA batteries: Recharging the batteries R/F Terminal Menu Functions Page Installing the 802 Terminal Utilities Software Chapter 2 RF System Setup RF Terminal Setup RF Terminal Default Settings 2-2 Default RF Terminal Configuration Using the bar code RF Terminal Setup Menu To use the bar coded Setup Menu, scan these bar codes in this order: Using the keypad to setup the RF Terminal Page RF Terminal Setup Parameters Device IP Address Server IP Address SSID WEP Encryption Key Authentication LCD Backlight Display Mode Backlight Duration Skip Opening Screens Speaker and Headphone Volume Controls Automatic Check Back Code 3 of 9 (Code 39) UPC/EAN Code 128 Codabar 2 of 5 Code 2 of 5 Length MSI and Plessey RSS-14 Code 93 Beep Tone Date Format Set Date Set Time Display of Year Voice Message Partitions Shut Down Time Laser Scanner Options Aiming Dot Duration Reset Page Chapter 3 Operational Theory Basic RF System communications A little more in depth Page Can I change a prompt after it has been sent? Page Chapter 4 Performance Issues Evaluating your area of planned operation Page Page Chapter 5 Before you begin programming Failure Planning Chapter 6 Programming for the 802 RF Terminal Introduction Objects, Properties, Methods, and Events Signing In, Data Structures, Transactions, and State Management Page WD802Term/ActiveX Programming Considerations Network Setup Server Communications Control Keys for Possible Programming Concepts WD802Term ActiveX Properties WD802Term ActiveX Page Methods WD802Term ActiveX Page Page Page Page Events WD802Term ActiveX Page Page Portable Printers Cameo and QL 320 Common Information Zebra Cameo Printer Zebra QL 320 Printer Page Page Chapter 7 Voice Message Operations Why Use Voice Messages and Prompts? Tips for Using Voice Prompts 802 RF Terminals Voice Message Mapping Programming Voice Messages Recording and Playback of Voice Messages Default Voice Messages Cloning Voice Messages and Setup from 802 RF Terminal to 802 RF Terminal Page Page Chapter 8 Troubleshooting General Considerations System Test Radio Test Changing Batteries Page 8-3 Terminal Error Messages Message Meaning Action Required Troubleshooting specific problems RF Terminal Problems Problems reading Bar Codes If you have a problem Appendix A Printer Pin-outs Laser and CCD Remember: Page Appendix B Firmware Upgrades R/F Terminal Firmware Upgrades Firmware Download via Radio Link Serial Firmware Download for a Terminal Failsafe Firmware Download for a Terminal Appendix C Code 39 Specifications *C39* Code 39 Advanced Features and Functions Mod 43 Check Character Full ASCII Extension to Code 39 Accumulate Mode Appendix D Code 93 Specifications Page Appendix E Codabar Specifications Codabar start/stop transmission Page Appendix F Code 128 Specifications UCC-128/ EAN-128 Page Appendix G Interleaved 2 of 5 Code Specifications Interleaved 2 of 5 Mod 10 check digit calculation Page Appendix H UPC / EAN Specifications Supplemental codes ISBN Specifications The UPC/EAN checksum character Checksum calculation for UPC-A, EAN-13 and EAN-8 UPC-E Checksum Calculation Appendix I MSI/Plessey Specifications Page Appendix J How to scan a bar code Laser and CCD Scanners Laser Options Aiming the Laser Dot: "Difficult Code 39 Reading": Page Appendix K Using the Scan Stand Page Appendix L Optional Features CCD Scanners LI50 Linear Imager Scanner Laser Scanners LZ300 Laser Scanner Laser Accessories H11 Laser Holder RF Terminal Cases and Holsters F41 Leather RF Terminal Carrying Case T46 Holster for RF Terminal Rubber Boot for RF Terminal M-1 Appendix M ASCII Code Equivalent Table Full ASCII Equivalent Table Page N-1 Appendix N 802 Display Character Code Mapping Page O-1 Appendix O 802 RF Terminal Setup Menu */A/* */B/* */C/* */%/* */5/* O-2 */S/* */W/* */R/* */O/* */L/* *.3.* */V/* *.5.* */D/* */S/* */I/* */F/* *.6.* */6/* *.0.* */4/* */G/* */H/* Page *%U* Page Page Page Index 1 2 4 6 D E F H I K L M Q R S T U V W X Y Z