Worth Data 802 RF user manual Setup Mode

Sequence error - avoiding	3-3
Sequence Error	8-3

Serial printer setup paramters on terminal2-18 Server Communications

using the 802 Test program		6-5
Server IP Address		2-5
Server Not Available		8-3
Server not Available message		3-2
Server Re-initialized		8-3
Server Shut Down	......................................	8-3
Set Date		2-15
Set Time		2-15
Setup for RF Terminal		2-5
Setup Cloning to other terminals		7-4
Setup Menu
"Reset" bar code		2-17
Baud Rate		2-18
Data Bits		2-18
Parity		2-18
RF Terminal parameters		2-5
Stop Bits		2-18
SETUP MODE
using to program voice messages		7-2
SETUP MODE Menu Option		1-4
Setup or playback voice messages		7-3
Shared Key Authentication		2-6
shelf label printing		6-18
Shut Down Time		2-16
Shut Down Time feature		1-1
SIGN OUT - missing the message		5-2
signal strength of access points		4-2
Signing In, Data Structures, Transactions,
and State Management		6-2
Signing out in mid-transaction		5-2
SITE SURVEY Menu Option		1-4
site survey results		4-2
Six beeps on power up		8-4
Skip Opening Screens		2-7
SPEAKER VOLUME		2-8
SSID		2-6
Stand mode	See hands free laser scanning

Start Setup - scanning to enter Setup mode2-2

Start/stop characters
transmitting for Codabar	2-12
transmitting for Code 39	2-10
Starting Channel	2-5
STATUS key
reserved for date/time only	6-6
using to determine battery life	8-2
Steps for installation	1-1
STK bar code	2-12
Stop Bits for serial printer	2-18
Storage Tek bar code	2-12
Storage Tek Tape Label code	2-11
Subnet Mask	2-5
substitution errors	J-2
Substitutions of data	J-3
sunlight problems, aiming dot	J-3

T

T49 Holster for RF Terminal	L-3
Tape library bar code	2-12
terminal cycles power	8-4
terminal goes back to opening screen	8-4
Terminal keys
transmitting ASCII values	2-6
Terminal Out of Range Message	3-2
Terminal setup Encryption Key	2-6
Terminal Setup Cloning
to other terminals	7-4
Terminal Tracking	6-6
Time Set	2-15
Tips for Using Voice Prompts	7-1
Transaction examples for VB	6-3
Transmission Delayed	8-3
Transmitting Bar Code ID's	2-12

Transmitting Codabar start and stop characters2-12

Transmitting EAN-8/UPC-E in original
formats	2-11
Transmitting through walls	4-2
TriOptic Code 39	2-11
Troubleshooting	8-1
Turning on the R/F Terminal	1-1
turns off and on by itselt	8-4

U

UCC 128 Serial Shipping Container bar
code	F-2
UCC/EAN Code 128
enabling/disabling	2-11
UCC-128/ EAN-128	F-1
UP ARROW key
transmitting ASCII 28 to host	6-6

UPC 2 and 5-character supplemental codesH-2

UPC/EAN	2-10
about	H-1
Check digit	H-1
compressed format	2-11
default settings	2-10
guidelines for use	H-2
NSC and check digit	2-11
NSC's and check digits	2-10
numbering conventions	H-2
supplemental codes	2-10
UPC-A - adding a country code	2-10
UPC-A in 13 digit EAN format	2-10
UPC/EAN check digits
enabling transmission of	2-11
UPC/EAN checksum character	H-3
UPC/EAN Specifications	H-1
UPC/EAN Supplements
enabling/disabling	2-10
UPC-E Checksum Calculation	H-4
UPC-E0 and UPC-E1	2-11
UPC-E1 - enabling reading of	2-12
Updating firmware	B-1

5