Manuals / Brands / Computer Equipment / Credit Card Machine / Worth Data / Computer Equipment / Credit Card Machine

Worth Data 802 RF Default RF Terminal Configuration , Using the bar code RF Terminal Setup Menu , ,

1 119

Download 119 pages, 1.71 Mb

2-2

Default RF Terminal Configuration

Parameter Default Setting Parameter Default Setting

Device IP DHCP Server Used Disabled

Server IP Device Searches Start/Stop not transmitted

Subnet Mask 255.255.255.0

Codabar

CLSI format disabled

Starting Channel 1 Disabled

SSID None check digit not transmitted

WEP Encryption None Plessey Code disabled

MSI Code

Label Code4 and 5 disabled

Enabled Enabled

Accumulate Mode ON

Code 128

EAN/UCC 128 disabled

stop/start chs not xmit Code 11 Disabled

check digit disabled RSS-14 Disabled

Caps lock OFF Disabled

Code 39

Full ASCII Enabled

Code 93

Full ASCII enabled

Disabled Beep Tone medium

I 2 of 5 Code disabled Date Format mm-dd-yy

6 digit code length Baud Rate 19200

2 of 5 Code

check digit disabled Parity none

Enabled Data Bits 8

UPC supps disabled Stop Bits 1

Batteries Alkaline default UPC-A NSC & check digit

transmitted Speaker

Speaker Volume 5

Headphone Volume 5

UPC-A NSC & check digit

transmitted Laser Options none

Shut Down Time 5 minutes EAN-13 country code &

check digit transmitted Voice Messages 303015

Encryption none EAN-13 country code &

check digit transmitted Control Keys Only no

Display of year 2 digit UPC-E 1st char & check

digit not transmitted Skip opening screens no

Aiming Dot No

UPC-E 1st char & check

digit not transmitted Automatic Check Back No

EAN-8 1st char & check

digit not transmitted Display Backlight Duration 5 seconds

UPC/ EAN

EAN-8 1st char & check

digit not transmitted

*All parameters are set back to their defaults when reset using the bar coded Setup Menu, even

parameters that are changed by keypad only. Shaded items are keypad access only.

Using the bar code RF Terminal Setup Menu

To use the bar coded Setup Menu, scan these bar codes in this order:

• Start Setup - you should hear 2 beeps

• Setup Parameter bar code (i.e. “Beep Tone”)-you should hear 2

beeps for each scan

• Number bar code that corresponds to the appropriate setting

(i.e. “3” to change the Beep Tone to “high”) - you should hear 2

beeps for each scan

• End Setup-you should hear 3 beeps after END SETUP.

Contents

Main Table of Contents Page Chapter 1 Installation Components Installation Tips Page Battery Life Indicator To change the AA batteries: Recharging the batteries R/F Terminal Menu Functions Page Installing the 802 Terminal Utilities Software Chapter 2 RF System Setup RF Terminal Setup RF Terminal Default Settings 2-2 Default RF Terminal Configuration Using the bar code RF Terminal Setup Menu To use the bar coded Setup Menu, scan these bar codes in this order: Using the keypad to setup the RF Terminal Page RF Terminal Setup Parameters Device IP Address Server IP Address SSID WEP Encryption Key Authentication LCD Backlight Display Mode Backlight Duration Skip Opening Screens Speaker and Headphone Volume Controls Automatic Check Back Code 3 of 9 (Code 39) UPC/EAN Code 128 Codabar 2 of 5 Code 2 of 5 Length MSI and Plessey RSS-14 Code 93 Beep Tone Date Format Set Date Set Time Display of Year Voice Message Partitions Shut Down Time Laser Scanner Options Aiming Dot Duration Reset Page Chapter 3 Operational Theory Basic RF System communications A little more in depth Page Can I change a prompt after it has been sent? Page Chapter 4 Performance Issues Evaluating your area of planned operation Page Page Chapter 5 Before you begin programming Failure Planning Chapter 6 Programming for the 802 RF Terminal Introduction Objects, Properties, Methods, and Events Signing In, Data Structures, Transactions, and State Management Page WD802Term/ActiveX Programming Considerations Network Setup Server Communications Control Keys for Possible Programming Concepts WD802Term ActiveX Properties WD802Term ActiveX Page Methods WD802Term ActiveX Page Page Page Page Events WD802Term ActiveX Page Page Portable Printers Cameo and QL 320 Common Information Zebra Cameo Printer Zebra QL 320 Printer Page Page Chapter 7 Voice Message Operations Why Use Voice Messages and Prompts? Tips for Using Voice Prompts 802 RF Terminals Voice Message Mapping Programming Voice Messages Recording and Playback of Voice Messages Default Voice Messages Cloning Voice Messages and Setup from 802 RF Terminal to 802 RF Terminal Page Page Chapter 8 Troubleshooting General Considerations System Test Radio Test Changing Batteries Page 8-3 Terminal Error Messages Message Meaning Action Required Troubleshooting specific problems RF Terminal Problems Problems reading Bar Codes If you have a problem Appendix A Printer Pin-outs Laser and CCD Remember: Page Appendix B Firmware Upgrades R/F Terminal Firmware Upgrades Firmware Download via Radio Link Serial Firmware Download for a Terminal Failsafe Firmware Download for a Terminal Appendix C Code 39 Specifications *C39* Code 39 Advanced Features and Functions Mod 43 Check Character Full ASCII Extension to Code 39 Accumulate Mode Appendix D Code 93 Specifications Page Appendix E Codabar Specifications Codabar start/stop transmission Page Appendix F Code 128 Specifications UCC-128/ EAN-128 Page Appendix G Interleaved 2 of 5 Code Specifications Interleaved 2 of 5 Mod 10 check digit calculation Page Appendix H UPC / EAN Specifications Supplemental codes ISBN Specifications The UPC/EAN checksum character Checksum calculation for UPC-A, EAN-13 and EAN-8 UPC-E Checksum Calculation Appendix I MSI/Plessey Specifications Page Appendix J How to scan a bar code Laser and CCD Scanners Laser Options Aiming the Laser Dot: "Difficult Code 39 Reading": Page Appendix K Using the Scan Stand Page Appendix L Optional Features CCD Scanners LI50 Linear Imager Scanner Laser Scanners LZ300 Laser Scanner Laser Accessories H11 Laser Holder RF Terminal Cases and Holsters F41 Leather RF Terminal Carrying Case T46 Holster for RF Terminal Rubber Boot for RF Terminal M-1 Appendix M ASCII Code Equivalent Table Full ASCII Equivalent Table Page N-1 Appendix N 802 Display Character Code Mapping Page O-1 Appendix O 802 RF Terminal Setup Menu */A/* */B/* */C/* */%/* */5/* O-2 */S/* */W/* */R/* */O/* */L/* *.3.* */V/* *.5.* */D/* */S/* */I/* */F/* *.6.* */6/* *.0.* */4/* */G/* */H/* Page *%U* Page Page Page Index 1 2 4 6 D E F H I K L M Q R S T U V W X Y Z