Xantrex Technology 120 VAC/60 owner manual Setup Menu MAP, FLT Sell SLT LBX

MENU SYSTEM

SETUP MENU MAP

The SETUP MENU provides all the controls and settings needed when installing or adjusting the system. To access the SETUP MENU, press both the red ON/OFF MENU and green GEN MENU buttons on the Control Panel at the same time. To exit the SETUP MENU, press the red ON/OFF MENU button or press the down MENU HEADING button until you reach the USER MENU (menu headings 1-8).

MENU HEADINGS

Inverter Setup	Battery Charging	AC Inputs		Gen Auto Start		Gen starting		Auxiliary Relays
9	10		11	setup	12	details	13	R9 R10 R11	14

MENU ITEMS

Set Grid Usage

FLT SELL SLT LBX

Set Low battery cut out VDC 11.0

Set LBCO delay

minutes	10
Set Low battery
cut in VDC	13.0
Set High battery
cut out VDC	16.0
Set search
watts	48
Set search
spacing	59

Set Bulk
volts DC	14.4
Set Absorption
time h:m	02:00
Set Float
volts DC	13.4
Set Equalize
volts DC	14.4
Set Equalize
time h:m	02:00
Set Max Charge
amps AC	20

Set Temp Comp

LeadAcid NiCad

Set Grid (AC1)

amps AC	60
Set Gen (AC2)
amps AC	30
Set Input lower
limit VAC	108
Set Input upper
limit VAC	132

Set Load Start

amp AC	20
Set Load Start
delay min	5.0
Set Load Stop
delay min	5.0
Set 24 hr start
volts DC	12.3
Set 2 hr start
volts DC	11.8
Set 15 min start
volts DC	11.3
Read LBCO 30 sec
start VDC	11.0
Set Exercise
period days	30
Set Maximum run
time h:m	08:00

Set Max Run time to 0 to defeat.

Set Exercise to 0 to defeat.

See menu 9 to to set LBCO.

Set RY7 Function GlowStop Run

Set Gen warmup

seconds 60

Set Pre Crank

seconds 10

Set Max Cranking

seconds 10

Set Post Crank

seconds 30

Set Relay 9

volts DC	14.5
R9 Hysteresis
volts DC	01.0
Set Relay 10
volts DC	14.8
R10 Hysteresis
volts DC	01.0
Set Relay 11
volts DC	15.0
R11 Hysteresis
volts DC	01.0
Close on batt >
setpoint.
Open on	batt <

setpoint - Hys

Relays have 2 second delay on

Close, 0.1 sec delay on open

Bulk Charge		Low Battery		Battery Selling		Grid Usage Timer		Information file		End Setup Menu
Trigger Timer 15		Transfer (LBX) 16			17		18	battery	19	20
Set Start Bulk		Set Low Battery		Set Battery Sell		Start Charge		Batt temp comp
time	00:00	TransferVDC	11.3	volts DC	13.4	time	21:00	changes battery
To disable timer		Set Low battery		Set Max Sell		End Charge		voltage reading
set to 00:00		cut in VDC	13.0	amps AC	30	time	21:00	away from actual
If grid timer		See menu 9 to		See menu 9 to		After Start		HBCO resets at:
active set bulk		enable LBX mode.		enable SELL mode.		Charge time:		6v/48, 3v/24 and
time after start		Make sure LBX is		Make sure LBX is		SELL mode		1.5v/12v under
charge time.		above LBCO volts.		above LBCO volts.		charges battery.		HBCO.
In SLT mode don’t						FLT mode		LowBattTransfer
disable this						charges battery		used in LBX, FLT
timer. It is the						After End Charge		Modes only. Goes
daily chg time.						time:		back to battery
						SELL mode sells		at LowBattCutIn
						battery to AC1.		(aka LBCI).
						FLT mode drops		For LBX mode set
						AC1 and inverts		below LBCI so
						Timer on when		charger won’t
						start < > end;		cycle batteries
						timer off when		up and down and
						start = end		set LBCO below.

Sell and float modes use timer

SLT and LBX mode ignore timer

 2001 Xantrex Technology, Inc.	Telephone: 360/435-8826	SW Series Inverter/Charger
5916 - 195th Street N. E.	Fax: 360/435-2229	Part No. 2031-5
Arlington, WA 98223	www.traceengineering.com	Rev. C: February 2001

Page

35