Yamaha 01v owner manual Parameter Change 7bit operation for type 0x10edit buffer

282 MIDI Data Format

PARAMETER CHANGE (7bit operation for type 0x10:edit buffer)

Reception

This message is received if [Parameter Change RX] is ON and the [Rx CH] matches the Device Channel included in the SUB STATUS. This is echoed if [Parameter Change ECHO] is ON.

When this is received, the specified parameter will be controlled.

Transmission

If [Parameter Change TX] is ON, this message is transmitted on the [Tx CH] Device Channel when a parameter not specified in the [Control Assign Table] is modified.

STATUS	11110000	F0	System Exclusive Message
ID No.	01000011	43	Manufacturer's ID No.(YAMAHA)
SUB STATUS	0001nnnn 1n		parameter change n=0-15(Device Chan-
			nel No.1-16)
GROUOP ID	00111110	3e	MODEL ID
MODEL ID	00000100	04	Device code (01V)
PARAM TYPE	00010000	10	7bit operation for edit buffer (type)
DATA	0aaaaaaa dd0		address( H) high 7 bits of 14 bits address
	0aaaaaaa dd1		address( L) low 7 bits of 14 bits address
	0ddddddd dd2		data 7bit
	:		:
EOX	11110111	F7	End Of Exclusive

The valid range of addresses is 0x0000 - 0x03FF

PARAMETER CHANGE (bit operation for type 0x40:edit buffer)

Reception

When [Parameter Change RX] is ON, this message is received if the [Rx CH] matches the Device Channel included in the SUB STATUS. If [Parameter Change ECHO] is ON, this message will be echoed.

When this message is received, the specified parameter will be con- trolled.

Transmission

If [Parameter Change TX] is ON, this message is transmitted on the [Tx CH] Device Channel when a parameter not specified in the [Control Assign Table] is modified.

STATUS	11110000	F0	System Exclusive Message
ID No.	01000011	43	Manufacturer's ID No.(YAMAHA)
SUB STATUS	0001nnnn 1n		parameter change n=0-15(Device Chan-
			nel No.1-16)
GROUOP ID	00111110	3e	MODEL ID
MODEL ID	00000100	04	Device code (01V)
PARAM TYPE	01000000	40	bit operation for edit buffer (type)
DATA	0aaaaaaa dd0		address( H) high 7 bits of 14 bits address
	0aaaaaaa dd1		address( L) low 7 bits of 14 bits address
	0ddddddd dd2		data(bit0-2:change bit no.0-7, bit3:0=reset
			1=set)
	:		:
EOX	11110111	F7	End Of Exclusive

The valid range of addresses is 0x0000 - 0x03FF

PARAMETER CHANGE (byte operation for type 0x01:system memory)

Reception

When [Parameter Change RX] is ON, this message is received if the [Rx CH] matches the Device Channel included in the SUB STATUS. When [Parameter Change ECHO] is ON, this is echoed.

When this is received, the specified parameter will be controlled.

STATUS	11110000	F0	System Exclusive Message
ID No.	01000011	43	Manufacturer's ID No.(YAMAHA)
SUB STATUS	0001nnnn 1n		parameter change or response
			n=0-15(Device Channel No.1-16)
GROUOP ID	00111110	3e	MODEL ID
MODEL ID	00000100	04	Device code (01V)
PARAM TYPE	00000001	01	byte operation for system memory (type)
DATA	0aaaaaaa dd0		address( H) high 7 bits of 14 bits address
	0aaaaaaa dd1		address( L) low 7 bits of 14 bits address
	0000dddd dd2		data( H) high 4 bits of 8 bits data
	0000dddd dd3		data( L) low 4 bits of 8 bits data
	:		: continuous address datas
EOX	11110111	F7	End Of Exclusive

The system memory will depend on the address, as follows.

0x0000 - 0x007F : setup memory(128byte)

0x0080 - 0x0147 : backup memory(200byte)

0x0200 : card type(1byte)

PARAMETER CHANGE (bit operation for type 0x41:system memory)

Reception

When [Parameter Change RX] is ON, this message is received if the [Rx CH] matches the Device Channel included in the SUB STATUS. When [Parameter Change ECHO] is ON, this is echoed.

When this is received, the specified parameter will be controlled.

STATUS	11110000	F0	System Exclusive Message
ID No.	01000011	43	Manufacturer's ID No.(YAMAHA)
SUB STATUS	0001nnnn 1n		parameter change or response
			n=0-15(Device Channel No.1-16)
GROUOP ID	00111110	3e	MODEL ID
MODEL ID	00000100	04	Device code (01V)
PARAM TYPE	01000001	41	bit operation for system memory (type)
DATA	0aaaaaaa dd0		address( H) high 7 bits of 14 bits address
	0aaaaaaa dd1		address( L) low 7 bits of 14 bits address
	0ddddddd dd2		data(bit0-2:change bit no.0-7, bit3:0=reset
			1=set)
	:		:
EOX	11110111	F7	End Of Exclusive

The system memory will depend on the address, as follows.

0x0000 - 0x007F : setup memory(128byte)

0x0080 - 0x0147 : backup memory(200byte)

01V—Owner’s Manual