Dist-Delay, Multi Filter | Yamaha 01v instruction

156 Chapter 12—Effects

DIST->DELAY

Distortion and delay effects in series.

	Parameter	Range	Description

	DST TYPE	DST1, DST2, OVD1,	Distortion type (DST = distortion, OVD = overdrive)
	DST TYPE	OVD2, CRUNCH	Distortion type (DST = distortion, OVD = overdrive)
		OVD2, CRUNCH

	DRIVE	0–100	Distortion drive

	MASTER	0–100	Master volume

	TONE	–10 to +10	Tone control

	N.GATE	0–20	Noise reduction

	DLY BAL	0–100%	Distortion and delay balance (0% = distortion, 100%
	DLY BAL	0–100%	= delayed distortion)
			= delayed distortion)

	DELAY	0.0–2725.0 ms	Delay time

	DLY NOTE	*1	Used in conjunction with TEMPO to determine DELAY

	FB.GAIN	–99 to +99%	Feedback gain (plus values for normal-phase
	FB.GAIN	–99 to +99%	feedback, minus values for reverse-phase feedback)
			feedback, minus values for reverse-phase feedback)

	HI.RATIO	0.1–1.0	High-frequency feedback ratio

	FREQ.	0.05–40.00 Hz	Modulation speed

	MOD	*2	Used in conjunction with TEMPO to determine FREQ.
	NOTE	*2	Used in conjunction with TEMPO to determine FREQ.
	NOTE

	DEPTH	0–100%	Modulation depth

	TEMPO*3	25–300 bps	Used in conjunction with NOTE parameters to
	TEMPO*3	25–300 bps	determine DELAY and FREQ.
			determine DELAY and FREQ.

	1.		(Maximum value depends
	on the tempo setting)
	2.

3.For more information about the DELAY, NOTE, and TEMPO parameters, see “Setting Delay, Freq, Note & Tempo Parameters” on page 137.

MULTI FILTER

Three-band parallel ﬁlter (24 dB/octave)

Parameter	Range	Description

TYPE 1	HPF, LPF, BPF	Filter 1 type: low pass, high pass, band pass

TYPE 2	HPF, LPF, BPF	Filter 2 type: low pass, high pass, band pass

TYPE 3	HPF, LPF, BPF	Filter 3 type: low pass, high pass, band pass

FREQ. 1	28 Hz–16.0 kHz	Filter 1 frequency

FREQ. 2	28 Hz–16.0 kHz	Filter 2 frequency

FREQ. 3	28 Hz–16.0 kHz	Filter 3 frequency

LEVEL 1	0–100	Filter 1 level

LEVEL 2	0–100	Filter 2 level

LEVEL 3	0–100	Filter 3 level

RESO. 1	0–20	Filter 1 resonance

RESO. 2	0–20	Filter 2 resonance

RESO. 3	0–20	Filter 3 resonance

01V—Owner’s Manual

Image 166

Yamaha 01v Dist-Delay, Multi Filter, Distortion and delay effects in series, Three-band parallel ﬁlter 24 dB/octave

Contents

Owner’s Nederland Netherlands Important Information Read the Following Before Operating Interference Package ContentsKeep this manual for future reference Copyright Contents Solo, Monitors & Meters Stereo Output Bus Outs Stereo Output DelayAux Sends Omni Outs Dynamics Processors 161 EffectsScene Memories Other Functions Using the Digital Inputs & OutputsTroubleshooting Appendix a General Midi Appendix D Resources 291 Appendix B SpecificationsAppendix C Midi Glossary Index Welcome to This chapter 01V Installation Welcome to 01V Features 01V Features01V Sonic Specs Conﬁguration Key Feature DiscussionBeneﬁts of a Digital Mixer Four-band Parametric EQ & Library 01V Sonic PerformanceMotorized Faders Option I/O & Digital I/O Onboard Effects ProcessorsOnboard Dynamics Processors Easy-to-Learn GUI Interface Midi Welcome to Getting Started 01V System Example This example shows the kind of system possible with Turning On Connecting the Power CordImportant Wordclock Information Turning Off Getting Started Touring Top Panel Controls 13/14 15/16 Analog Control Section Display, Selected Channel Controls & Meters Parameter Wheel, Cursors & Enter Function Buttons Fader Mode ButtonsDelay Button Pages Solo buttons SEL, SOLO, on buttons & FadersSEL buttons On buttons Faders Solo Status IndicatorSolo status indicator lights up when a channel is soloed Return Controls Top Panel Inputs & OutputsInput BAL 2TR Rear Panel Phantom +48V ON-OFF SwitchesOmni OUTs Power switch Option I/O slot Diagram Block Block Diagram Touring Getting Around the User Interface About the User Interface Function Buttons Fader Mode ButtonsDisplay Display Rotary Controls SwitchesDisplay Elements Parameter Boxes DEC & +1/INC Buttons Cursor ButtonsParameter Wheel Enter Button SEL Buttons SEL button Fader Mode 13/14Fader Modes Input Channel SEL button Examples Master SEL Button Examples Solo button Fader Mode 13/14Solo Buttons Usage Examples Input Channel on button Examples On button Fader Mode 13/14On Buttons Master on Button Examples Faders plus Return Rotary Controls Faders are used to adjust channel levelsFader Rotary Control Fader Mode 13/14 Input Channel Level Examples Input Channel Effects Send Examples Master Level Examples Title Edit Dialog Box Getting Around the User Interface Attenuating Input Channel Signals Input Channels Input Channel Overview This section provides an overview of 01V input channels Setting Input Channel Gain Phantom PoweringPad Switches Metering Input Channels Normal phase Reversed phase Changing the Input PhaseInput channels 17 through 24 do not have Phase switches Attenuating Input Channel Signals For Input Channels Applying EQ to Input Channels Input Channels Dynamics Processors Delaying Channel Signals Parameter Range Description Setting Input Channel Levels Muting Input Channels For Input Channels 1-16 & the Effects Returns Panning Input ChannelsUse the PAN control to pan the selected channel Pan Modes Be located using the Option I/O buttonIncluding center, there are 33 pan positions Routing Input Channels Input Channels & the Omni Outs Monitoring Input ChannelsInput Channels & Aux Sends Input Channels & the Option I/O Outs Swapping Inputs 1-8 Pairing Input Channels Making Input Channel Pairs Following dialog box appears Releasing Input Channel PairsSelect OK, and then press the Enter button Input Channel Pair Block Diagram Making Fader Groups Fader group enabled Fader group disabledGrouping Faders Enabling & Disabling Fader Groups Grouping Mutes Use the Setup button to locate Setup page 3, as shown belowMute group enabled Mute group disabled Making a Mute Group Viewing Input Channel Settings Use the View button to locate View page 1 or Input Channels Copying & Swapping Channel Settings Input Channel Block Diagram Gain This chapter About the 01V EQ Adjusting the EQ For Effects Returns 1 For Aux Sends Press the Home button Press the Master SEL button For the Stereo OutputST is the selected channel Bypassing the EQ Resetting the EQEQ Specs Following table contains the EQ specs EQ Library Preset EQ Program ListTitle See Title Edit Dialog Box on page 37 for more information Storing EQ ProgramsEnter a title for the EQ program EQ program is stored Recalling EQ Programs Edit the program title Editing EQ Program TitlesTitle Edit dialog box appears New title is stored Preset EQ Program Parameters Title Parameter Description MID High Corrects arpeggio tech Use for the low range Solo, Monitors & Meters About Monitor & Solo Phones Monitor OutputsTwo-track Input 2TR Using Monitor Monitor SetupTo monitor, for example, the stereo out, proceed as follows Monitor Block Diagram Solo Setup Using Solo Use Solo buttons 1 through 16 to solo channels Block Diagram Solo Effects Returns, Aux Sends & Bus Outs Metering Signal LevelsUse the Home button to locate the following Home pages Main Stereo Meters Peak Hold Option I/O Meters input channels Setting the Metering PointUse the Option I/O button to locate the Option pages Effects Send Meters Stereo Output Coaxial Digital Out & the Stereo Output 2TR Out & the Stereo Output About the Stereo OutputAnalog Stereo Output Coaxial Digital Out & the Stereo Output Metering the Stereo Output Routing Signals to the Stereo OutputViewing Stereo Output Settings Press the Home button, and then the Master SEL button Balancing the Stereo Output Setting the Stereo Output LevelMuting the Stereo Output Applying EQ to the Stereo Output Stereo Output Delay 300 ms Stereo Output Block Diagram 101 Aux Sends100 104 Omni Outs & the Aux Sends About the Aux SendsOption I/O & the Aux Sends Monitoring Aux Sends Sending Channel Signals to Aux Sends Use the AUX buttons to select an aux send For Effects Returns 1 Pre-fader/Post-fader Aux Sends Viewing Aux Send Settings Setting Aux Send Master Levels Use the Master fader to set the aux send master level Aux Send Dynamics Processors Muting Aux SendsApplying EQ to Aux Sends Use the Master on button to turn the aux send on or off Making Aux Send Pairs Pairing Aux SendsReleasing Aux Send Pairs Panning Channel Aux Sends Pairing Aux Sends Aux Send Block Diagram Stereo Send Block Aux Sends Bus Outs Option I/O & the Bus Outs Routing Signals to the Bus OutsAbout the Bus Outs Omni Outs & the Bus Outs Setting Bus Out Master Levels Muting Bus Outs Routing Bus Signals to the Stereo Bus Making Bus Out Pairs Pairing Bus OutsReleasing Bus Out Pairs Bus Out Block Diagram Stereo Pair Bus Out Block Diagram 113 Bus Outs Omni Outs About the Omni Outs Omni out signals are converted to analogUsing 18-bit D/A converters, and then output Omni Outs Omni Out Delay Omni Out Block Diagram Effects About the Onboard Effects Reverb-type Effects Preset Effects ProgramsDelays Modulation-type Effects Dynamic Effects Guitar EffectsCombined Effects Using the Effects Raise the channel’s fader i.e., effects send level control Press the Home button Returning Processed SignalsProcessed signal is returned into the mix Faders now function as regular channels faders Pre-fader/Post-fader Effects Sends 125 For Input Channels Viewing Effects Send Settings Metering Effects Sends Setting Effects Send Master Levels Use the Master fader to set the effects send master level Muting Effects Sends Use the Master on button to turn the effects send on or off Applying EQ to Effects Returns Viewing Effects Returns SettingsMetering Effects Returns Muting Effects Returns Routing Effects Returns Setting Effects Returns LevelsPanning Effects Returns Monitoring Effects Returns Effects Library Title the effects program Storing Effects ProgramsEffects program is stored Recalling Effects Programs Editing Effects Program Titles Program is stored with its new title Editing Effects EFFECT1 page 1 is shown below Setting Delay, Freq, Note & Tempo Parameters Early REF Effects ParametersReverb HALL, Reverb ROOM, Reverb STAGE, Reverb Plate Hall, room, stage, and plate simulations, all with gates 139 Mono DelayBasic repeat delay Gate REVERB, Reverse Gate Basic stereo delay Stereo DelayMOD.DELAY Basic repeat delay with modulation Delay LCR 141 Echo Stereo delay with crossed feedback loopChorus 143 PhaserStage phaser Symphonic Tremolo AutopanHQ.PITCH Effect 2 only Rotary 145Dual Pitch Twin-voice pitch shifter MOD.FILTER Ring MODDistortion DYNA.FILTER 147AMP Simulate DYNA.FLANGE REV+CHORUS DYNA.PHASERDynamically controlled phaser Reverb and chorus effects in parallel REV+FLANGE 149REV-CHORUS Reverb and ﬂanger effects in parallel Reverb and ﬂanger effects in series REV-FLANGEREV+SYMPHO Reverb and symphonic effects in parallel REV-PAN 151REV-SYMPHO Reverb and symphonic effects in series DELAY+ER Delay and early reﬂections effects in parallel Delay and early reﬂections effects in series DELAY-ER153 DELAY+REV Delay and reverb effects in parallel DELAY-REV 155 Multi Filter DIST-DELAYDistortion and delay effects in series Three-band parallel ﬁlter 24 dB/octave Basic Sampler with 2.9 second memory 157To record and playback a sample Effects Effects Block Diagram Effects Dynamics Processors About the Dynamics Processors Preset Dynamics Programs Title Type Using the Dynamics Processors Using the Dynamics Processors Editing the Dynamics Processors Comp Processor TypesParameter Range Gate Ducking Announcer to be heard clearly. The same Expand Compander Hard & Soft 172 Dynamics Library Title the dynamics program Storing Dynamics ProgramsDynamics program is stored Recalling Dynamics Programs Dynamics programs 1 through 80 can be recalled Editing Dynamics Program Titles Preset Dynamics Program Settings 177 178 Value Description 179 180 181 Dynamics Processors Scene Memories About Scene Memories What’s Stored in Scene Memories? Scene Memory About the Edit Buffer & IndicatorScene Memory Display Area Mix scenes can be stored in scene memories 1 through Storing Mix ScenesTitle the mix scene Recalling Mix Scenes Recalling Mix Scenes Using Midi Program Change Messages Protecting Scene Memories Undoing Mix Scene RecallsPress the Enter button Renumbering Scene Memories Editing Scene Memory TitlesEdit the scene memory title Setting a Fade Time Safe Channel switches appear highlighted for safe channels Recalling Scene Data Safely Other Functions Assigning Faders & On Buttons Fader Assignments Parameter Channel On Button Assignments 13-14 Initial Assignments for BankChannel Control Parameter 15-16 198 Effect EFFECT1 PARAM1 Effect EFFECT2 PARAM1 Use this table for your own assignments 201User Assignment table Channel Control Using the Oscillator Setting 01V Preferences Preferences are used to customize the operation Calibrating the Faders Initial SettingsInitializing Turn off While holding down the Memory button, turn on Using the Digital Inputs & Outputs Assigning Option I/O Digital Outputs About Wordclocks Digitally Recording to DAT Multitrack Recording Multitrack Recording with Digital DAT Source Setting the Wordclock Using the Digital Inputs & Outputs Digital Stereo Out 01V Output Dither Digital Stereo Link Port Cascading 01VsMidi Local Control Cascading Aux Sends Cascade Delay Cascading Two or More 01Vs MY4-DA Analog Output About Option I/O CardsMY8-TD Tascam MY8-AD 8 Analog Input 217 Card Description Inputs Outputs ConnectorCard Speciﬁcations Installing Option I/O Cards Assigning Option I/O Digital Outputs 219 Option I/O Inputs Midi Midi & Midi Ports Using the Midi Ports Using the to Host Port01V Using the Link Port Midi Receive IndicatorsMidi Setup Use the Midi button to locate Midi page 1, as shown below Setting Computer Platform Port Transmission Speed Mac Midi Program Change Scene Recall Using Program Changes 01V-A Control Change Parameter Control 229 Using Control Changes System Exclusive Parameter Control 231 Bulk Dump Switch of the selected category appears highlightedData Type Range Description Using Midi Bulk Dump 01V Local Control 01V-A remote On Button Function MMC Command Value Midi Machine Control Midi Machine Control Switch of the active bank appears highlighted User Deﬁned Midi Controllers Linking 01Vs 01V-A Linking 01Vs using the Midi Ports 01V-B System Examples Wordclock Conﬁguration 01V & ADAT-Interface RecorderSystem Components System Notes Wordclock slave Two 01Vs & two ADAT-Interface Recorders Two 01V Digital Mixing Consoles Two MY8-AT Option I/O cards 01V-A 01V & Tascam-Interface Recorder TDIF-1 Two 01Vs & two Tascam-Interface Recorders Interface 01V & Pro Tools AES/EBU 01V & Pro Tools AES/EBU Pro Tools wordclock master Monitors System Examples Input channel signal levels are too Symptom AdviceEQ F and G controls adjust Cannot access input channels 254 Effects send meters indicate That signals are being sent to Symptom Advice Added channels to a mute groupCannot send channel signals to Update some channels 256 01V Level Diagram Appendix a General Display Messages Security Cover Rack-mounting Kit Appendix a General General Appendix B Speciﬁcations261 Dimensions W ⋅ H ⋅ D Power requirementsPower consumption Weight Input Channels Option I/O Inputs 17-24 need optional card Return 1, 2 Internal Effect 1 Stereo Out BusAux Omni Out Option I/O Output need optional card Monitor Out SoloMemories & Libraries Low Lo-Mid*1 Hi-Mid1 High Gain G Analog Inputs Analog Outputs Digital Audio Outputs Digital Audio InputsOption I/O Cards Connection Format Level Connector Control I/O 01V Dimensions Appendix B Specifications Program Initial User Change # Appendix C MidiScene Memory to Program Change Table Change# Control Parameter Change # 01V Initial Default User 01V Parameter to Control Change Table Parameter Change # 01V Initial Default User 275 Change # 01V Initial Default User 276 No Assign Fader Channel 278 279 Control Change Bn Midi Data FormatTRANSMIT/RECEIVE Data Program Change Cn Parameter Change Transmission ConditionReceive Condition Active Sensing Fe Parameter Change byte operation for type 0x01system memory Parameter Change 7bit operation for type 0x10edit bufferParameter Change bit operation for type 0x40edit buffer Parameter Change bit operation for type 0x41system memory Parameter Change type 0x02function calltitle Parameter Change type 0x02function callParameter Value Request type 0x02function calltitle Parameter Change type 0x04multiple linking Parameter CHANGEtype 0x05remote meter RequestParameter Value REQUESTtype 0x05remote meter REMOTEInternal Parameter Memory Bulk Dump Format REMOTEInternal Parameter Memory Bulk Dump Request Format REMOTEUser Deﬁne Memory Bulk Dump Format REMOTEUser Deﬁne Memory Bulk Dump Request Format Dynamics Library Bulk Dump Format Program Change Assignment Table Bulk Dump Format Control Change Assignment Table Bulk Dump Format Midi Implementation Chart Books Appendix D ResourcesYamaha Web Site Appendix D Resources Glossary De-emphasis-SeeEmphasis EFF-Abbreviation for effect Glossary Glossary Index SymbolsNumerics DIST-DELAY Flange Freeze HQ.PITCH Omni OUT Midi Index View page 3 59 Viewing settings aux sends Yamaha Corporation