Yamaha 01v owner manual Parameter Change type 0x04multiple linking

284 MIDI Data Format

PARAMETER CHANGE (type operation for type 0x03:controller(LCD-Fader mode))

Reception

When [Parameter Change RX] is ON and the [Rx CH] matches the Device Channel included in the SUB STATUS, the message will be received.

When [Parameter Change ECHO] is ON, this message will be ech- oed.

When this message is received, the LCD screen, the corresponding Fader Mode, and the specified channel will be selected.

STATUS	11110000	F0	System Exclusive Message
ID No.	01000011	43	Manufacturer's ID No.(YAMAHA)
SUB STATUS	0001nnnn 1n		parameter change n=0-15(Device Chan-
			nel No.1-16)
GROUOP ID	00111110	3e	MODEL ID
MODEL ID	00000100	04	Device code (01V)
PARAM TYPE	01000011	03	controller (type)
DATA	00000001	01	control No.(LCD-Fader mode)
	0ddddddd dd		channel select(0-30)
	0ddddddd dd		LCD select No.(0-17)
	0000dddd dd		PAGE No.(0-4)
EOX	11110111	F7	End Of Exclusive

PARAMETER CHANGE (bit operation for type 0x43:controller(key remote))

Reception

When [Parameter Change RX] is ON and the [Rx CH] matches the Device Channel included in the SUB STATUS, this message will be received.

When [Parameter Change ECHO] is ON, this message will be ech- oed.

When this message is received, the same processing will be performed as when the specified key (refer to the table below) is pressed (released).

Transmission

When [Parameter Change ECHO] is ON, this message will be trans- mitted without change.

STATUS	11110000		F0	System Exclusive Message
ID No.	01000011		43	Manufacturer's ID No.(YAMAHA)
SUB STATUS	0001nnnn 1n			parameter change n=0-15(Device Chan-
				nel No.1-16)
GROUOP ID	00111110		3e	MODEL ID
MODEL ID	00000100		04	Device code (01V)
PARAM TYPE	01000011		43	controller
DATA	00000000		00	control no.(0:key remote)
	0ddddddd dd			No. 0-10,99-102(key 1-11,100-103)
	0000dddd dd			data(bit0-2:change bit no.0-7,
				bit3:0=reset 1=set)
		:		:
EOX	11110111		F7	End Of Exclusive
KEY key no.bit0	bit1	bit2	bit3	bit4	bit5	bit6	bit7

-------------------------------------------------------------------------------------------------------------------------------------------------

key1	0	ON1	ON2	ON3	ON4	ON5	ON6	ON7	ON8
key2	1	ON9	ON10	ON11	ON12	ON13-14	ON15-16	ONSTOUT	------
key3	2	SOLO1	SOLO2	SOLO3	SOLO4	SOLO5	SOLO6	SOLO7	SOLO8
key4	3	SOLO9	SOLO10	SOLO11	SOLO12	SOLO13-14SOLO15-16		------	------
key5	4	SEL1	SEL2	SEL3	SEL4	SEL5	SEL6	SEL7	SEL8
key6	5	SEL9	SEL10	SEL11	SEL12	SEL13-14	SEL15-16	SEL STO	------
key7	6	ONRTN1	ONRTN2	SOLORT1	SOLORT2	SELRTN1	SELRTN2	HOME	MEMORY
key8	7	AUX1	AUX2	AUX3	AUX4	EFFECT1	EFFECT2	OPTION	REMOTE
key9	8	LOW	L-MID	H-MID	HIGH	------	------	------	------
key10	9	UP	LEFT	RIGHT	DOWN	ENTER	INC	DEC	------
key11	10	DYNAMIX EQ		DELAY	PAN	UTILITY	MIDI	SETUP	VIEW
key100	99	FRZ-REC	FRZ-PLAY	------	------	------	------	------	------
key101	100	SOLO1	SOLO2	SOLO3	SOLO4	SOLO5	SOLO6	SOLO7	SOLO8
key102	101	SOLO9	SOLO10	SOLO11	SOLO12	SOLO13-14SOLO15-16		SOLO-RTN1 SOLO-RTN2
key103	102	SOLO17	SOLO18	SOLO19	SOLO20	SOLO21	SOLO22	SOLO23	SOLO24

*Normally, data should be transmitted as "set(bit3=1)." In this case, the 01V will determine that that switch has been pressed and then immediately released, and will perform the appropriate processing. This means that you will not have to transmit "reset(bit3=0)" sepa- rately.

*The keys followed by 100 are virtual key, it would be the keys on LCD.

PARAMETER CHANGE (type 0x04:multiple linking)

This message is valid only for the connector that has been specified as the LINK PORT.

When two '01V' units have been connected by a cable, some of the functions (refer to the following table) will be linked.

The same LINK PORT connector settings must be made on both units.

Reception

This message is always received, and will execute the LINK function (refer to the following table). (This is not dependent on MIDI-SETUP.)

Transmission

This message is transmitted when LINK-related functions (refer to following table) are performed. (This is not dependent on MIDI-SETUP.)

When [Parameter Change ECHO] is ON, this message is transmitted without change.

STATUS	11110000	F0	System Exclusive Message
ID No.	01000011	43	Manufacturer's ID No.(YAMAHA)
SUB STATUS	0001nnnn 1n		n=0-15(Tx/Rx Channel No.1-16)
GROUOP ID	00111110	3e	MODEL ID
MODEL ID	00000100	04	Device code (01V)
PARAM TYPE	00000100	04	multiple linking
DATA	0mmfffff mf		data format (bit6-5:status, bit4-0:contents)
	0ddddddd dd0		data #0
	0ddddddd dd1		data #1
	:	:
EOX	11110111	F7	End Of Exclusive
Status Function		Note

----------------------------------------------------------------------------------------------------------

0x00	scene recall	Recall the specified memory number
0x01	scene store	Store to the specified memory number with title
		(Assign the same title to all)
0x02	scene title edit	If the title was modified, make it the same, make it
		match
0x48	solo mode	Match the solo mode
	bit6: enable/disable
	bit5: on/off
	bit2: recording/mixdown
	bit1: sel mix/last
	bit0: after fader/pre fader
0x60	display call	When the screen (Fader Mode) is changed, make it
		match
0x61	metering point	Make the meter points match
0x62	peak hold	Make the meter Peak Hold ON/OFF match

01V—Owner’s Manual