Troubleshooting
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
“CHECK SP WIRES” | Speaker cables are | Make sure all speaker cables are connected correctly. | 13 | |
appears in the front |
|
|
| |
panel display. |
|
|
| |
|
|
|
| |
There is noise | This unit is too close to the digital or high- | Move this unit further away from such equipment. | — | |
interference from | frequency equipment. |
|
| |
digital or radio |
|
|
| |
frequency equipment. |
|
|
| |
|
|
|
| |
The picture is | The video source uses scrambled or |
|
| |
disturbed. | encoded signals to prevent dubbing. |
|
| |
|
|
|
| |
This unit suddenly | The internal temperature is too high and | Wait about 1 hour for this unit to cool down and then | — | |
enters the standby | the overheat protection circuitry has been | turn it back on. |
| |
mode. | activated. |
|
| |
|
|
|
|
■Remote control
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
The remote control | Wrong distance or angle. | The remote control will function within a maximum | 27 | |
does not work or |
| range of 6 m and no more than 30 degrees |
| |
function properly. |
| from the front panel. |
| |
|
|
|
| |
| Direct sunlight or lighting (from an | Reposition this unit. | — | |
| inverter type of fluorescent lamp, etc.) is |
|
| |
| striking the remote control sensor of this |
|
| |
| unit. |
|
| |
|
|
|
| |
| The batteries are weak. | Replace all batteries. | 4 | |
|
|
|
| |
| The operation mode selector is set | Set the operation mode selector correctly. | — | |
| incorrectly. | When operating this unit, set it to the KAMP |
| |
|
| position.When operating the component selected by |
| |
|
| the input selector button, set it to the KSOURCE |
| |
|
| position.When operating the TV set in the DTV or |
| |
|
| PHONO area, set it to the KTV position. |
| |
|
|
|
| |
| The remote control code was not correctly | Set the remote control code correctly using | 79 | |
| set. | “List of remote control codes” at the end of this |
| |
|
| manual. |
| |
|
|
|
| |
|
| Try setting another code of the same manufacturer | 79 | |
|
| using “List of remote control codes” at the end of this |
| |
|
| manual. |
| |
|
|
|
| |
| The library code of the remote control and | Match the remote control ID of this unit with the | 90,91 | |
| the remote control ID of this unit do not | corresponding remote control library code. |
| |
| match. |
|
| |
|
|
|
| |
| Even if the remote control code is | Program the necessary functions independently into | 81 | |
| correctly set, there are some models that | the programmable buttons using the Learn feature. |
| |
| do not respond to the remote control. |
|
| |
|
|
|
| |
The remote control | The batteries of this remote control and/or | Replace the batteries. | 4 | |
does not learn new | the other remote control are too weak. |
|
| |
functions. |
|
|
| |
The distance between the two remote | Place the remote controls at the proper distance. | 81 | ||
| ||||
| controls is too much or too little. |
|
| |
|
|
|
| |
| The signal coding or modulation of the | Learning is not possible. | — | |
| other remote control is not compatible |
|
| |
| with this remote control. |
|
| |
|
|
|
| |
| Memory capacity is full. | Delete other unnecessary functions to make room for | 87 | |
|
| the new functions. |
| |
|
|
|
|
INFORMATION | ADDITIONAL |
|
|
English
