Printer with retract, Fitting a Shutter | Zebra Technologies 7030

Maintenance

Fitting A Shutter

Fitting A Shutter

Figure 23 • Fitting a Shutter

103

Standard printer

Allen screw/hub (2x)

Shutter

Printer with retract

The shutter kit contains a shutter and two hub-screws. In addition to this, you need an 1.5 mm Allen-key.

1.Fit one hub screw.

2.Hook the shutter onto the screw and insert the other screw, through the hole in the shutter and into the thread in the printer.

3.Make sure the head of the screw goes into the hole of the shutter and then tighten it.

4.Verify that the shutter opens/closes as it should by printing a couple of documents.

10/05/2009

TTP 7030™ Technical Manual

P1003636-002

Image 103

Zebra Technologies 7030 technical manual Printer with retract, Fitting a Shutter

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 About This Manual IntroductionUpdating Subject line Emaillist  Contacts Printer Exterior, Rear View Product Presentation Printer Exterior, Side View Status Indicator IndicatorsControl Board Indicators Feed Button Installation Top view Installation Considerations Ambient Light Electrostatic Discharges, and Earth Currents Using a Serial Adapter Connecting To The ComputerConnect the TTP Fitting a serial adapter to the printer GND Connecting the Power Making a Test Printout Is a power button available for the printer? Installing a Printer Driver Paper Level Sensors Paper Level Sensor Indicators on Roll Holder Paper-near-end Sensor Connection Operation Make sure the printer is turned on Installing a Paper Roll Cut the paper in a suitable angle. See Figure Angle Open the Print Module Clearing Paper Jams Programming Text text How The Commands Are Described Therefore, the two-byte representation of 731 is Two-Byte Character Definitions Summary Of Control Codes & Escape Sequences 27 5 Device ID Enquiry 27 5 Head temperature Enquiry27 5 Bootware version Enquiry 50 n1 27 5 80 n1 Parameter-setting data Enquiry Black Mark Top-Of-Form Commands Software Command Syntax Changes the alignment of text and logotypes Text CommandsLeft Center Right Turns OFF Italics Normal Turns on Italics Selects normal font font ESC ! 4 selects fontSelects font ESC ! 5 selects font Selects font ESC T n1 Reversed/Inversed Text ESC w n1 Overprint the O Commands, are not cancelled ESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes Specified in any order Specifies the bar code field No -15. Bar code fields may be Must be placed at the end of the bar code data But other values than 0 to 15 are ignoredN2 . . . nx Specifies bar code data bytes Add-on. Two of five characters are allowed of the add-on Columns Error level, 0=auto, 1=Level0, 2=Level1, etcDot Height, sets mow many pixel lines each row consists Determines the number of bytes. Range Graphics Commands ESCr000000000000001193000024003 ESC g n1 Print Logotype Print buffer full Press on FF-button Print CommandsForm feed Clear presenter Run presenter ESC j n1 Paper Reverse Gives a cut & eject after the last text line Cut And Present CommandsYou can also use RS together with the paper advance command To auto Retracts the presented Ejects the presented ENQ Erases all logotypes stored in the flash Prom System Related Commands Erases all fonts stored in the flash Prom Set several parameters at once See Default Parameter Settings on Status Reporting Commands Paper-near-end Enquiry Read  Send  Sensor Status That is, a response with the value 129 indicates version Readn Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h File Format Font Loading Character bitmap data Loading Logotypes Printing All logotypes are erased with the ESC&L command Status Reporting Default Parameter Settings Programming Default Value Default Parameter Settings Summary Of Parameter Settings Serial Interface Set-Up Hardware Select what handshaking to use on the serial interfaceNo flow control Xon / Xoff No, paper out and error signals are not disabled Parallel Port SetupYes, paper out and error signals are disabled Cm loop Print SetupDisable the loop Current consumption Burn pulses + history Controls what the printer does with buffered dataBurn pulse + history Burn pulse On the paper Black mark synchronization enabledCR = Ignored LF = Ignored Be extended, while longer documents will be divided into Contents printouts shorter than the value specified byDetermines what should control the page length Fixed Document Mode. Shorter documents will automatically Length P37 P38 Fixed Document Mode Add 30-mm top margin Sets max black mark length to 5 mmSets min black mark length to 4 mm Feeds 50 mm between black mark and cut Will be retracted. Range 1-30, 1 step = 10 s Eject page when new page is printed. Retract disabledRetract page when new page is printed Do nothing when new page is printed. Auto-eject and retract Paper Near End indication OffAutomatic Distance Calculation No indication Default Parameter Settings Setup N43 N44 Printable Area Recommended black mark size and position Aligning Preprint And Thermal Print Setup Parameters Used Enables/disables black mark check Garbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Send  Text and graphics Specified by the ESC x commandSend  RS Cuts and ejects the printout Simple Calibration Process Black-Mark Sensing from Within Windows Interface Cable ground Cable powerUSB Interface + Data Serial Option, TTP Setup Options Interface Maintenance Fault Finding Fault Finding 101 Cleaning The Print Head Fitting a Shutter Printer with retract Firmware Specifications None, Odd or Even Print Data Basic Character Set Command Code Modes Non-Windows Applications 108 109 Paper Handling Bar Codes Non-Windows Applications Environmental Conditions Printer Dimensions Thermal coating Paper SpecificationMiscellaneous General Preprinting Perforation Print can be expected within a zone of approximately 2-mm Black Mark Size and PositionAround the edges of the hole. The function must be tested Part Number List AccessoriesPrinters 116 117 Roll Holder for Paper Rolls up to 150 mm Roll Holders 119 120 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration 122 Numerics Index Index Index USB Connector PortPage Zebra Technologies Europe Limited