Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies 7030 Connecting To The Computer, Connect the TTP, Using a Serial Adapter

Models: 7030

1 128

Download 128 pages 16.1 Kb

Page 16

16

Installation

Connecting To The Computer

Connecting To The Computer

Caution • Using a non-Zebra power supply may cause excessive EMC interferences and void the EMC certifications of the printer.

Connect the TTP 7030

1.Connect J13 of the printer to the USB port of the computer or the USB hub to be used. USB connectors can be recognized by the following symbol:

.

Note • Connector J13 is a 4-pin USB type B connector. See USB, TTP 7030 on page 877 for pin assignment.

Note • A suitable cable is available from Zebra, see Ordering numbers on page 115 for ordering number.

Figure 4 • USB Cable with Type A and Type B Connectors

Using a Serial Adapter

1.Loosen the control board module; see Removal on page 110.

2.Connect the serial adapter to J4 on the control board.

3.Fasten the control board module; see Removal on page 110.

4.Fasten the serial adapter with the two screws on the right hand side of the printer.

5.Connect a Zebra serial cable, ordering No.10825-000, between the printer and the computer to be used.

Important • We strongly recommend using the Zebra cable because many incompatible cables are available.

P1003636-002

TTP 7030™ Technical Manual

10/05/2009

Image 16

Zebra Technologies 7030 technical manual Connecting To The Computer, Connect the TTP, Using a Serial Adapter

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 About This Manual IntroductionUpdating Contacts Subject line Emaillist Product Presentation Printer Exterior, Rear ViewPrinter Exterior, Side View Status Indicator IndicatorsControl Board Indicators Feed Button Installation Installation Considerations Top viewElectrostatic Discharges, and Earth Currents Ambient LightUsing a Serial Adapter Connecting To The ComputerConnect the TTP Fitting a serial adapter to the printer Connecting the Power GNDIs a power button available for the printer? Making a Test PrintoutInstalling a Printer Driver Paper Level Sensor Indicators on Roll Holder Paper Level SensorsPaper-near-end Sensor Connection Operation Installing a Paper Roll Make sure the printer is turned onAngle Cut the paper in a suitable angle. See FigureClearing Paper Jams Open the Print ModuleProgramming Text text How The Commands Are Described Two-Byte Character Definitions Therefore, the two-byte representation of 731 isSummary Of Control Codes & Escape Sequences 27 5 Head temperature Enquiry 27 5 Bootware version Enquiry50 n1 27 5 80 n1 Parameter-setting data Enquiry 27 5 Device ID EnquirySoftware Command Syntax Black Mark Top-Of-Form CommandsChanges the alignment of text and logotypes Text CommandsLeft Center Right Selects normal font font ESC ! 4 selects font Selects font ESC ! 5 selects fontSelects font Turns OFF Italics Normal Turns on ItalicsESC T n1 Reversed/Inversed Text ESC w n1 Commands, are not cancelled Overprint the OESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes Specifies the bar code field No -15. Bar code fields may be Specified in any orderBut other values than 0 to 15 are ignored N2 . . . nx Specifies bar code data bytesAdd-on. Two of five characters are allowed of the add-on Must be placed at the end of the bar code dataColumns Error level, 0=auto, 1=Level0, 2=Level1, etcDot Height, sets mow many pixel lines each row consists Graphics Commands Determines the number of bytes. RangeESCr000000000000001193000024003 ESC g n1 Print Logotype Print Commands Form feed Clear presenterRun presenter Print buffer full Press on FF-buttonESC j n1 Paper Reverse Cut And Present Commands You can also use RS together with the paper advance commandTo auto Gives a cut & eject after the last text lineEjects the presented Retracts the presentedENQ System Related Commands Erases all logotypes stored in the flash PromErases all fonts stored in the flash Prom See Default Parameter Settings on Set several parameters at onceStatus Reporting Commands Paper-near-end Enquiry Send  Read Sensor Status Readn Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 129 indicates versionThat is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h Font Loading File FormatCharacter bitmap data Logotypes LoadingAll logotypes are erased with the ESC&L command PrintingStatus Reporting Default Parameter Settings Programming Default Parameter Settings Default ValueSummary Of Parameter Settings Serial Interface Set-Up Select what handshaking to use on the serial interface No flow controlXon / Xoff HardwareNo, paper out and error signals are not disabled Parallel Port SetupYes, paper out and error signals are disabled Print Setup Disable the loopCurrent consumption Cm loopControls what the printer does with buffered data Burn pulse + historyBurn pulse Burn pulses + historyBlack mark synchronization enabled CR = IgnoredLF = Ignored On the paperContents printouts shorter than the value specified by Determines what should control the page lengthFixed Document Mode. Shorter documents will automatically Be extended, while longer documents will be divided intoFixed Document Mode Length P37 P38Sets max black mark length to 5 mm Sets min black mark length to 4 mmFeeds 50 mm between black mark and cut Add 30-mm top marginEject page when new page is printed. Retract disabled Retract page when new page is printedDo nothing when new page is printed. Auto-eject and retract Will be retracted. Range 1-30, 1 step = 10 sOff Automatic Distance CalculationNo indication Paper Near End indicationDefault Parameter Settings Setup Printable Area N43 N44Aligning Preprint And Thermal Print Recommended black mark size and positionSetup Enables/disables black mark check Parameters UsedGarbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Send  Text and graphics Specified by the ESC x commandSend  RS Cuts and ejects the printout Simple Calibration Process Black-Mark Sensing from Within Windows Interface Cable power USB Interface+ Data Cable groundSetup Options Serial Option, TTPInterface Maintenance Fault Finding Fault Finding101 Cleaning The Print Head Printer with retract Fitting a ShutterFirmware Specifications Print Data None, Odd or EvenCommand Code Modes Non-Windows Applications Basic Character Set108 109 Bar Codes Non-Windows Applications Paper HandlingPrinter Dimensions Environmental ConditionsPaper Specification MiscellaneousGeneral Thermal coatingPerforation PreprintingPrint can be expected within a zone of approximately 2-mm Black Mark Size and PositionAround the edges of the hole. The function must be tested Part Number List AccessoriesPrinters 116 117 Roll Holders Roll Holder for Paper Rolls up to 150 mm119 120 中国 RoHS 材料声明 China RoHS Material Declaration 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。122 Index NumericsIndex Index Connector Port USBPage Zebra Technologies Europe Limited