Indicators, Status Indicator | Zebra Technologies 7030 instruction

Product Presentation

Indicators

Indicators

Status Indicator

The status indicator (see Figure 1, Printer Exterior, Rear View , on page 9) has several functions:

ON constantly	Indicates that the printer is operational.

Flashes, pauses, flashes	Indicates warnings of non-severe error. The number of flashes
	reflects the warning-code:
	• 2 flashes: Paper low
	Note • This signaling is disabled by default. It can be
	disabled/enabled by setting parameter P52.
	• 3 flashes: Weekend low
	Warning-codes are reset automatically when the condition
	causing them are removed.

Flashes rapidly	Indicates severe error. Hold down the Feed button and the
	number of flashes will reflect the error-code.
	• 1 — Presenter jam, paper cannot be ejected / retracted
	• 2 — Cutter cannot return to home position
	• 3 — Out of paper
	• 4 — Printhead lifted
	• 5 — Paper wrapped around platen (under head)
	• 6 — Temp error >60°C
	• 7 — Presenter jam, motor cannot rotate
	• Fast flashes — Checksum error, firmware
	• Steady light — Wrong firmware type

Error-codes are reset:

•When the conditions causing them are removed.

•When the printer is turned off/on.

•When the blue printhead release arm is lifted and then lowered.

Control Board Indicators

The control board has two power indicators behind the power connector:

•Green indicator constantly ON: 24 V present

•Red indicator constantly ON: 5 V OK (generated on control board)

11

10/05/2009

TTP 7030™ Technical Manual

P1003636-002

Image 11

Zebra Technologies 7030 technical manual Status Indicator, Control Board Indicators

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 Updating IntroductionAbout This Manual Subject line Emaillist  Contacts Printer Exterior, Rear View Product Presentation Printer Exterior, Side View Control Board Indicators IndicatorsStatus Indicator Feed Button Installation Top view Installation Considerations Ambient Light Electrostatic Discharges, and Earth Currents Connect the TTP Connecting To The ComputerUsing a Serial Adapter Fitting a serial adapter to the printer GND Connecting the Power Making a Test Printout Is a power button available for the printer? Installing a Printer Driver Paper Level Sensors Paper Level Sensor Indicators on Roll Holder Paper-near-end Sensor Connection Operation Make sure the printer is turned on Installing a Paper Roll Cut the paper in a suitable angle. See Figure Angle Open the Print Module Clearing Paper Jams Programming Text text How The Commands Are Described Therefore, the two-byte representation of 731 is Two-Byte Character Definitions Summary Of Control Codes & Escape Sequences 27 5 Device ID Enquiry 27 5 Head temperature Enquiry27 5 Bootware version Enquiry 50 n1 27 5 80 n1 Parameter-setting data Enquiry Black Mark Top-Of-Form Commands Software Command Syntax Left Center Right Text CommandsChanges the alignment of text and logotypes Turns OFF Italics Normal Turns on Italics Selects normal font font ESC ! 4 selects fontSelects font ESC ! 5 selects font Selects font ESC T n1 Reversed/Inversed Text ESC w n1 Overprint the O Commands, are not cancelled ESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes Specified in any order Specifies the bar code field No -15. Bar code fields may be Must be placed at the end of the bar code data But other values than 0 to 15 are ignoredN2 . . . nx Specifies bar code data bytes Add-on. Two of five characters are allowed of the add-on Dot Height, sets mow many pixel lines each row consists Error level, 0=auto, 1=Level0, 2=Level1, etcColumns Determines the number of bytes. Range Graphics Commands ESCr000000000000001193000024003 ESC g n1 Print Logotype Print buffer full Press on FF-button Print CommandsForm feed Clear presenter Run presenter ESC j n1 Paper Reverse Gives a cut & eject after the last text line Cut And Present CommandsYou can also use RS together with the paper advance command To auto Retracts the presented Ejects the presented ENQ Erases all logotypes stored in the flash Prom System Related Commands Erases all fonts stored in the flash Prom Set several parameters at once See Default Parameter Settings on Status Reporting Commands Paper-near-end Enquiry Read  Send  Sensor Status That is, a response with the value 129 indicates version Readn Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h File Format Font Loading Character bitmap data Loading Logotypes Printing All logotypes are erased with the ESC&L command Status Reporting Default Parameter Settings Programming Default Value Default Parameter Settings Summary Of Parameter Settings Serial Interface Set-Up Hardware Select what handshaking to use on the serial interfaceNo flow control Xon / Xoff Yes, paper out and error signals are disabled Parallel Port SetupNo, paper out and error signals are not disabled Cm loop Print SetupDisable the loop Current consumption Burn pulses + history Controls what the printer does with buffered dataBurn pulse + history Burn pulse On the paper Black mark synchronization enabledCR = Ignored LF = Ignored Be extended, while longer documents will be divided into Contents printouts shorter than the value specified byDetermines what should control the page length Fixed Document Mode. Shorter documents will automatically Length P37 P38 Fixed Document Mode Add 30-mm top margin Sets max black mark length to 5 mmSets min black mark length to 4 mm Feeds 50 mm between black mark and cut Will be retracted. Range 1-30, 1 step = 10 s Eject page when new page is printed. Retract disabledRetract page when new page is printed Do nothing when new page is printed. Auto-eject and retract Paper Near End indication OffAutomatic Distance Calculation No indication Default Parameter Settings Setup N43 N44 Printable Area Recommended black mark size and position Aligning Preprint And Thermal Print Setup Parameters Used Enables/disables black mark check Garbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Send  RS Cuts and ejects the printout Specified by the ESC x commandSend  Text and graphics Simple Calibration Process Black-Mark Sensing from Within Windows Interface Cable ground Cable powerUSB Interface + Data Serial Option, TTP Setup Options Interface Maintenance Fault Finding Fault Finding 101 Cleaning The Print Head Fitting a Shutter Printer with retract Firmware Specifications None, Odd or Even Print Data Basic Character Set Command Code Modes Non-Windows Applications 108 109 Paper Handling Bar Codes Non-Windows Applications Environmental Conditions Printer Dimensions Thermal coating Paper SpecificationMiscellaneous General Preprinting Perforation Around the edges of the hole. The function must be tested Black Mark Size and PositionPrint can be expected within a zone of approximately 2-mm Printers AccessoriesPart Number List 116 117 Roll Holder for Paper Rolls up to 150 mm Roll Holders 119 120 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration 122 Numerics Index Index Index USB Connector PortPage Zebra Technologies Europe Limited