Zebra Technologies 7030 instruction

Programming

Summary Of Control Codes & Escape Sequences

31

Summary Of Control Codes & Escape Sequences

Table 2 • Control Codes and Escape Sequences in Alphabetical Order

Command			Hex		Decimal	Function	Page
BS			08		8	Backspace	page 38
CAN			18		24	Cancel	page 38
CR			0D		13	Carriage return	page 38
EM			19	n1	25 n1	Enforced Clear Presenter	page 51
ENQ			05		5	Clear Presenter	page 52
ESC ACK		n1	1B	06 n1	27 6 n1	Acknowledge Marker	page 63
ESC !	n1		1B	21 n1	27 33 n1	Select Font	page 35
ESC #			1B	23 n1	27 35 n1	Calibrate Blackmark Sensor	page 33
ESC &	0		1B	26 00	27 38 0	Load Font	page 54
ESC &	1		1B	26 01	27 38 1	Load Logotype	page 53
ESC &	4		1B	26 04	27 38 4	Store current Parameter Values	page 53
ESC &	C		1B	26 43	27 38 67	Erase all Fonts	page 54
ESC &	D		1B	26 44	27 38 68	Erase Fonts 4 to 7	page 54
ESC &	F		1B	26 46 n1	27 38 70 n1	Recall Parameter Profile	page 54
ESC &	L		1B	26 4C	+27 38 76	Erase all Logotypes	page 53
ESC &	P		1B	26 50 n1...n2	27 38 80 n1...n2	Set Parameter Value	page 55
n1...n2
ESC ?			1B	3F	27 63	Reset (full)	page 53
ESC @			1B	40	27 64	Reset (initialize)	page 53
ESC b			1B	62 n1...n5	27 98 n1...n5	Print Bitmap at XY-position	page 45
n1...n5
ESC B	n1		1B	42 n1	27 66 n1	Bold	page 35
ESC B	C		1B	42 43 n1	27 66 67 n1	Barcode Clear	page 43
ESC B S			1B	42 53 n1...n11	27 66 83 n1...n11	Barcode Field Specify	page 42
n1...n11
ESC BW			1B	42 57 n1	27 66 87 n1	Barcode Write	page 43
ESC d	n1		1B	64 n1	27 100 n1	Make n Linefeeds	page 39
ESC ENQ		1	1B	05 01	27 5 1	Status Enquiry	page 56
ESC ENQ		002	1B	05 02	27 5 2	Paper-near-end Enquiry	page 57
ESC ENQ		004	1B	05 04	27 5 4	Fonts and Logotype Enquiry	page 58
ESC ENQ		6	1B	05 06	27 5 6	Status Report	page 59
ESC ENQ		7	1B	05 07	27 5 7	Firmware-version Enquiry	page 60
ESC ENQ		9	1B	05 09	27 5 9	Serial-number Enquiry	page 60
ESC ENQ		10	1B	05 0A	27 5 10	Control board revision Enquiry	page 60

10/05/2009

TTP 7030™ Technical Manual

P1003636-002

Image 31

Zebra Technologies 7030 technical manual Summary Of Control Codes & Escape Sequences

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 About This Manual IntroductionUpdating Subject line Emaillist  Contacts Printer Exterior, Rear View Product Presentation Printer Exterior, Side View Status Indicator IndicatorsControl Board Indicators Feed Button Installation Top view Installation Considerations Ambient Light Electrostatic Discharges, and Earth Currents Using a Serial Adapter Connecting To The ComputerConnect the TTP Fitting a serial adapter to the printer GND Connecting the Power Making a Test Printout Is a power button available for the printer? Installing a Printer Driver Paper Level Sensors Paper Level Sensor Indicators on Roll Holder Paper-near-end Sensor Connection Operation Make sure the printer is turned on Installing a Paper Roll Cut the paper in a suitable angle. See Figure Angle Open the Print Module Clearing Paper Jams Programming Text text How The Commands Are Described Therefore, the two-byte representation of 731 is Two-Byte Character Definitions Summary Of Control Codes & Escape Sequences 27 5 Device ID Enquiry 27 5 Head temperature Enquiry27 5 Bootware version Enquiry 50 n1 27 5 80 n1 Parameter-setting data Enquiry Black Mark Top-Of-Form Commands Software Command Syntax Changes the alignment of text and logotypes Text CommandsLeft Center Right Turns OFF Italics Normal Turns on Italics Selects normal font font ESC ! 4 selects fontSelects font ESC ! 5 selects font Selects font ESC T n1 Reversed/Inversed Text ESC w n1 Overprint the O Commands, are not cancelled ESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes Specified in any order Specifies the bar code field No -15. Bar code fields may be Must be placed at the end of the bar code data But other values than 0 to 15 are ignoredN2 . . . nx Specifies bar code data bytes Add-on. Two of five characters are allowed of the add-on Columns Error level, 0=auto, 1=Level0, 2=Level1, etcDot Height, sets mow many pixel lines each row consists Determines the number of bytes. Range Graphics Commands ESCr000000000000001193000024003 ESC g n1 Print Logotype Print buffer full Press on FF-button Print CommandsForm feed Clear presenter Run presenter ESC j n1 Paper Reverse Gives a cut & eject after the last text line Cut And Present CommandsYou can also use RS together with the paper advance command To auto Retracts the presented Ejects the presented ENQ Erases all logotypes stored in the flash Prom System Related Commands Erases all fonts stored in the flash Prom Set several parameters at once See Default Parameter Settings on Status Reporting Commands Paper-near-end Enquiry Read  Send  Sensor Status That is, a response with the value 129 indicates version Readn Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h File Format Font Loading Character bitmap data Loading Logotypes Printing All logotypes are erased with the ESC&L command Status Reporting Default Parameter Settings Programming Default Value Default Parameter Settings Summary Of Parameter Settings Serial Interface Set-Up Hardware Select what handshaking to use on the serial interfaceNo flow control Xon / Xoff No, paper out and error signals are not disabled Parallel Port SetupYes, paper out and error signals are disabled Cm loop Print SetupDisable the loop Current consumption Burn pulses + history Controls what the printer does with buffered dataBurn pulse + history Burn pulse On the paper Black mark synchronization enabledCR = Ignored LF = Ignored Be extended, while longer documents will be divided into Contents printouts shorter than the value specified byDetermines what should control the page length Fixed Document Mode. Shorter documents will automatically Length P37 P38 Fixed Document Mode Add 30-mm top margin Sets max black mark length to 5 mmSets min black mark length to 4 mm Feeds 50 mm between black mark and cut Will be retracted. Range 1-30, 1 step = 10 s Eject page when new page is printed. Retract disabledRetract page when new page is printed Do nothing when new page is printed. Auto-eject and retract Paper Near End indication OffAutomatic Distance Calculation No indication Default Parameter Settings Setup N43 N44 Printable Area Recommended black mark size and position Aligning Preprint And Thermal Print Setup Parameters Used Enables/disables black mark check Garbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Send  Text and graphics Specified by the ESC x commandSend  RS Cuts and ejects the printout Simple Calibration Process Black-Mark Sensing from Within Windows Interface Cable ground Cable powerUSB Interface + Data Serial Option, TTP Setup Options Interface Maintenance Fault Finding Fault Finding 101 Cleaning The Print Head Fitting a Shutter Printer with retract Firmware Specifications None, Odd or Even Print Data Basic Character Set Command Code Modes Non-Windows Applications 108 109 Paper Handling Bar Codes Non-Windows Applications Environmental Conditions Printer Dimensions Thermal coating Paper SpecificationMiscellaneous General Preprinting Perforation Print can be expected within a zone of approximately 2-mm Black Mark Size and PositionAround the edges of the hole. The function must be tested Part Number List AccessoriesPrinters 116 117 Roll Holder for Paper Rolls up to 150 mm Roll Holders 119 120 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration 122 Numerics Index Index Index USB Connector PortPage Zebra Technologies Europe Limited