Manuals / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies 7030 Electrostatic Discharges, and Earth Currents, Ambient Light

Models: 7030

1 128

Download 128 pages 16.1 Kb

Page 15

Installation

Installation Considerations

Electrostatic Discharges, and Earth Currents

Preventing ESD and earth currents from affecting the printer operation requires proper connection of the printer chassis to protective earth through a mounting platform or through a separate earth conductor.

Ambient Light

There is an optical sensor just inside the paper exit at the front of the printer.

To ensure proper printer operation, design the printer enclosure so that it prevents direct sunlight or light from indoor lamps from reaching the sensor through the paper exit.

15

10/05/2009

TTP 7030™ Technical Manual

P1003636-002

Image 15

Zebra Technologies 7030 technical manual Electrostatic Discharges, and Earth Currents, Ambient Light

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 Introduction About This ManualUpdating Subject line Emaillist  ContactsPrinter Exterior, Rear View Product PresentationPrinter Exterior, Side View Indicators Status IndicatorControl Board Indicators Feed Button Installation Top view Installation ConsiderationsAmbient Light Electrostatic Discharges, and Earth CurrentsConnecting To The Computer Using a Serial AdapterConnect the TTP Fitting a serial adapter to the printer GND Connecting the PowerMaking a Test Printout Is a power button available for the printer?Installing a Printer Driver Paper Level Sensors Paper Level Sensor Indicators on Roll HolderPaper-near-end Sensor Connection Operation Make sure the printer is turned on Installing a Paper RollCut the paper in a suitable angle. See Figure AngleOpen the Print Module Clearing Paper JamsProgramming Text text How The Commands Are Described Therefore, the two-byte representation of 731 is Two-Byte Character DefinitionsSummary Of Control Codes & Escape Sequences 27 5 Device ID Enquiry 27 5 Head temperature Enquiry27 5 Bootware version Enquiry 50 n1 27 5 80 n1 Parameter-setting data EnquiryBlack Mark Top-Of-Form Commands Software Command SyntaxText Commands Changes the alignment of text and logotypesLeft Center Right Turns OFF Italics Normal Turns on Italics Selects normal font font ESC ! 4 selects fontSelects font ESC ! 5 selects font Selects fontESC T n1 Reversed/Inversed Text ESC w n1 Overprint the O Commands, are not cancelledESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes Specified in any order Specifies the bar code field No -15. Bar code fields may beMust be placed at the end of the bar code data But other values than 0 to 15 are ignoredN2 . . . nx Specifies bar code data bytes Add-on. Two of five characters are allowed of the add-onError level, 0=auto, 1=Level0, 2=Level1, etc ColumnsDot Height, sets mow many pixel lines each row consists Determines the number of bytes. Range Graphics CommandsESCr000000000000001193000024003 ESC g n1 Print Logotype Print buffer full Press on FF-button Print CommandsForm feed Clear presenter Run presenterESC j n1 Paper Reverse Gives a cut & eject after the last text line Cut And Present CommandsYou can also use RS together with the paper advance command To autoRetracts the presented Ejects the presentedENQ Erases all logotypes stored in the flash Prom System Related CommandsErases all fonts stored in the flash Prom Set several parameters at once See Default Parameter Settings onStatus Reporting Commands Paper-near-end Enquiry Read  Send Sensor Status That is, a response with the value 129 indicates version Readn Where n can be ‘A’ Ascii or 41 hex or 65 decThat is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h File Format Font LoadingCharacter bitmap data Loading LogotypesPrinting All logotypes are erased with the ESC&L commandStatus Reporting Default Parameter Settings Programming Default Value Default Parameter SettingsSummary Of Parameter Settings Serial Interface Set-Up Hardware Select what handshaking to use on the serial interfaceNo flow control Xon / XoffParallel Port Setup No, paper out and error signals are not disabledYes, paper out and error signals are disabled Cm loop Print SetupDisable the loop Current consumptionBurn pulses + history Controls what the printer does with buffered dataBurn pulse + history Burn pulseOn the paper Black mark synchronization enabledCR = Ignored LF = IgnoredBe extended, while longer documents will be divided into Contents printouts shorter than the value specified byDetermines what should control the page length Fixed Document Mode. Shorter documents will automaticallyLength P37 P38 Fixed Document ModeAdd 30-mm top margin Sets max black mark length to 5 mmSets min black mark length to 4 mm Feeds 50 mm between black mark and cutWill be retracted. Range 1-30, 1 step = 10 s Eject page when new page is printed. Retract disabledRetract page when new page is printed Do nothing when new page is printed. Auto-eject and retractPaper Near End indication OffAutomatic Distance Calculation No indicationDefault Parameter Settings Setup N43 N44 Printable AreaRecommended black mark size and position Aligning Preprint And Thermal PrintSetup Parameters Used Enables/disables black mark checkGarbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Specified by the ESC x command Send  Text and graphicsSend  RS Cuts and ejects the printout Simple Calibration Process Black-Mark Sensing from Within Windows Interface Cable ground Cable powerUSB Interface + DataSerial Option, TTP Setup OptionsInterface Maintenance Fault Finding Fault Finding101 Cleaning The Print Head Fitting a Shutter Printer with retractFirmware Specifications None, Odd or Even Print DataBasic Character Set Command Code Modes Non-Windows Applications108 109 Paper Handling Bar Codes Non-Windows ApplicationsEnvironmental Conditions Printer DimensionsThermal coating Paper SpecificationMiscellaneous GeneralPreprinting PerforationBlack Mark Size and Position Print can be expected within a zone of approximately 2-mmAround the edges of the hole. The function must be tested Accessories Part Number ListPrinters 116 117 Roll Holder for Paper Rolls up to 150 mm Roll Holders119 120 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration122 Numerics IndexIndex Index USB Connector PortPage Zebra Technologies Europe Limited