Simple Calibration Process | Zebra Technologies 7030 specs

Page Setup

Parameters Used

Simple Calibration Process

1.Enable black mark mode by setting parameters n35 to n42 as described on the previous pages.

2.Load paper with black marks into the printer.

3.Send the <ESC># command and wait until the paper stops.

4.If the paper has returned to it's original position, the calibration is finished.

5.If not, it was not possible to distinguish the black mark. Check the n37 and n38 settings and try again).

6.Save the settings with <ESC>&<4>.

93

10/05/2009

TTP 7030™ Technical Manual

P1003636-002

Image 93

Zebra Technologies 7030 technical manual Simple Calibration Process

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 Introduction About This ManualUpdating Subject line Emaillist  Contacts Printer Exterior, Rear View Product Presentation Printer Exterior, Side View Indicators Status IndicatorControl Board Indicators Feed Button Installation Top view Installation Considerations Ambient Light Electrostatic Discharges, and Earth Currents Connecting To The Computer Using a Serial AdapterConnect the TTP Fitting a serial adapter to the printer GND Connecting the Power Making a Test Printout Is a power button available for the printer? Installing a Printer Driver Paper Level Sensors Paper Level Sensor Indicators on Roll Holder Paper-near-end Sensor Connection Operation Make sure the printer is turned on Installing a Paper Roll Cut the paper in a suitable angle. See Figure Angle Open the Print Module Clearing Paper Jams Programming Text text How The Commands Are Described Therefore, the two-byte representation of 731 is Two-Byte Character Definitions Summary Of Control Codes & Escape Sequences 27 5 Bootware version Enquiry 27 5 Head temperature Enquiry50 n1 27 5 80 n1 Parameter-setting data Enquiry 27 5 Device ID Enquiry Black Mark Top-Of-Form Commands Software Command Syntax Text Commands Changes the alignment of text and logotypesLeft Center Right Selects font ESC ! 5 selects font Selects normal font font ESC ! 4 selects fontSelects font Turns OFF Italics Normal Turns on Italics ESC T n1 Reversed/Inversed Text ESC w n1 Overprint the O Commands, are not cancelled ESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes Specified in any order Specifies the bar code field No -15. Bar code fields may be N2 . . . nx Specifies bar code data bytes But other values than 0 to 15 are ignoredAdd-on. Two of five characters are allowed of the add-on Must be placed at the end of the bar code data Error level, 0=auto, 1=Level0, 2=Level1, etc ColumnsDot Height, sets mow many pixel lines each row consists Determines the number of bytes. Range Graphics Commands ESCr000000000000001193000024003 ESC g n1 Print Logotype Form feed Clear presenter Print CommandsRun presenter Print buffer full Press on FF-button ESC j n1 Paper Reverse You can also use RS together with the paper advance command Cut And Present CommandsTo auto Gives a cut & eject after the last text line Retracts the presented Ejects the presented ENQ Erases all logotypes stored in the flash Prom System Related Commands Erases all fonts stored in the flash Prom Set several parameters at once See Default Parameter Settings on Status Reporting Commands Paper-near-end Enquiry Read  Send  Sensor Status That is, a response with the value 129 indicates version Readn Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h File Format Font Loading Character bitmap data Loading Logotypes Printing All logotypes are erased with the ESC&L command Status Reporting Default Parameter Settings Programming Default Value Default Parameter Settings Summary Of Parameter Settings Serial Interface Set-Up No flow control Select what handshaking to use on the serial interfaceXon / Xoff Hardware Parallel Port Setup No, paper out and error signals are not disabledYes, paper out and error signals are disabled Disable the loop Print SetupCurrent consumption Cm loop Burn pulse + history Controls what the printer does with buffered dataBurn pulse Burn pulses + history CR = Ignored Black mark synchronization enabledLF = Ignored On the paper Determines what should control the page length Contents printouts shorter than the value specified byFixed Document Mode. Shorter documents will automatically Be extended, while longer documents will be divided into Length P37 P38 Fixed Document Mode Sets min black mark length to 4 mm Sets max black mark length to 5 mmFeeds 50 mm between black mark and cut Add 30-mm top margin Retract page when new page is printed Eject page when new page is printed. Retract disabledDo nothing when new page is printed. Auto-eject and retract Will be retracted. Range 1-30, 1 step = 10 s Automatic Distance Calculation OffNo indication Paper Near End indication Default Parameter Settings Setup N43 N44 Printable Area Recommended black mark size and position Aligning Preprint And Thermal Print Setup Parameters Used Enables/disables black mark check Garbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Specified by the ESC x command Send  Text and graphicsSend  RS Cuts and ejects the printout Simple Calibration Process Black-Mark Sensing from Within Windows Interface USB Interface Cable power+ Data Cable ground Serial Option, TTP Setup Options Interface Maintenance Fault Finding Fault Finding 101 Cleaning The Print Head Fitting a Shutter Printer with retract Firmware Specifications None, Odd or Even Print Data Basic Character Set Command Code Modes Non-Windows Applications 108 109 Paper Handling Bar Codes Non-Windows Applications Environmental Conditions Printer Dimensions Miscellaneous Paper SpecificationGeneral Thermal coating Preprinting Perforation Black Mark Size and Position Print can be expected within a zone of approximately 2-mmAround the edges of the hole. The function must be tested Accessories Part Number ListPrinters 116 117 Roll Holder for Paper Rolls up to 150 mm Roll Holders 119 120 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。中国 RoHS 材料声明 China RoHS Material Declaration 122 Numerics Index Index Index USB Connector PortPage Zebra Technologies Europe Limited