Erases all fonts stored in the flash Prom | Zebra Technologies 7030

54

Programming

System Related Commands

ESC & 0		Load Font
1B 26 00	hex	Load Font
27 38 0	decimal

This command is used to load a font to the printer flash PROM. The font is placed in the first free address position in the order of load sequence.

A Zebra font-file consists of a header containing data describing the font as well as data for each individual character in the font.

Fonts can be designed with the font editor and loaded or deleted with the software available for free on the Zebra web site. The font loading and deleting commands described here should only be used if you do not work in the Windows environment.

For complete specification of the font format, see Font Loading on page 64.

Note • The available font memory is printed on the self-test printout. A maximum of 8 fonts can be addressed. Exceeding any of these limits will cause this command to fail.

ESC & C		Erase all Fonts
1B 26 43	Hex	Erase all Fonts
27 38 67	decimal

Erases all fonts stored in the flash PROM.

Note • This command is only executed if at least one font has been loaded.

ESC & D		Erase Fonts 4 to 7
1B 26 44	Hex	Erase Fonts 4 to 7
27 38 68	Decimal

Erases fonts number 4–7. Fonts 0–3 are not affected by this command.

The operation is complete when the printer resets automatically and activates the presenter motor temporarily. Takes approximately 4 seconds.

ESC & F		Reset Parameter Profile
1B 26 46	Hex	Reset Parameter Profile
27 38 70	decimal

This command resets the parameters of the printer to factory default.

Temporarily sets all parameters to predefined values that are stored in the printer. To keep the values as default, store them in the flash PROM with command <ESC>&<4>.

Unless you save the parameters, a reset command or power OFF/ON will return the parameters to the settings stored in the flash PROM.

P1003636-002

TTP 7030™ Technical Manual

10/05/2009

Image 54

Zebra Technologies 7030 technical manual Erases all fonts stored in the flash Prom

Contents

Zebra TTP P1003636-002 TTP 7030 Technical Manual 10/05/2009 Contents Programming Interface P1003636-002 TTP 7030 Technical Manual 10/05/2009 Introduction About This ManualUpdating Contacts Subject line Emaillist  Product Presentation Printer Exterior, Rear View Printer Exterior, Side View Indicators Status IndicatorControl Board Indicators Feed Button Installation Installation Considerations Top view Electrostatic Discharges, and Earth Currents Ambient Light Connecting To The Computer Using a Serial AdapterConnect the TTP Fitting a serial adapter to the printer Connecting the Power GND Is a power button available for the printer? Making a Test Printout Installing a Printer Driver Paper Level Sensor Indicators on Roll Holder Paper Level Sensors Paper-near-end Sensor Connection Operation Installing a Paper Roll Make sure the printer is turned on Angle Cut the paper in a suitable angle. See Figure Clearing Paper Jams Open the Print Module Programming Text text How The Commands Are Described Two-Byte Character Definitions Therefore, the two-byte representation of 731 is Summary Of Control Codes & Escape Sequences 50 n1 27 5 80 n1 Parameter-setting data Enquiry 27 5 Head temperature Enquiry27 5 Bootware version Enquiry 27 5 Device ID Enquiry Software Command Syntax Black Mark Top-Of-Form Commands Text Commands Changes the alignment of text and logotypesLeft Center Right Selects font Selects normal font font ESC ! 4 selects fontSelects font ESC ! 5 selects font Turns OFF Italics Normal Turns on Italics ESC T n1 Reversed/Inversed Text ESC w n1 Commands, are not cancelled Overprint the O ESC d n1 Make n Linefeeds Barcode Commands Samples of barcodes Specifies the bar code field No -15. Bar code fields may be Specified in any order Add-on. Two of five characters are allowed of the add-on But other values than 0 to 15 are ignoredN2 . . . nx Specifies bar code data bytes Must be placed at the end of the bar code data Error level, 0=auto, 1=Level0, 2=Level1, etc ColumnsDot Height, sets mow many pixel lines each row consists Graphics Commands Determines the number of bytes. Range ESCr000000000000001193000024003 ESC g n1 Print Logotype Run presenter Print CommandsForm feed Clear presenter Print buffer full Press on FF-button ESC j n1 Paper Reverse To auto Cut And Present CommandsYou can also use RS together with the paper advance command Gives a cut & eject after the last text line Ejects the presented Retracts the presented ENQ System Related Commands Erases all logotypes stored in the flash Prom Erases all fonts stored in the flash Prom See Default Parameter Settings on Set several parameters at once Status Reporting Commands Paper-near-end Enquiry Send  Read  Sensor Status Readn Where n can be ‘A’ Ascii or 41 hex or 65 dec That is, a response with the value 129 indicates version That is, a response with the value 130 indicates version Under Summary Of Parameter Settings on One-byte marker. Range 1h to 255h Font Loading File Format Character bitmap data Logotypes Loading All logotypes are erased with the ESC&L command Printing Status Reporting Default Parameter Settings Programming Default Parameter Settings Default Value Summary Of Parameter Settings Serial Interface Set-Up Xon / Xoff Select what handshaking to use on the serial interfaceNo flow control Hardware Parallel Port Setup No, paper out and error signals are not disabledYes, paper out and error signals are disabled Current consumption Print SetupDisable the loop Cm loop Burn pulse Controls what the printer does with buffered dataBurn pulse + history Burn pulses + history LF = Ignored Black mark synchronization enabledCR = Ignored On the paper Fixed Document Mode. Shorter documents will automatically Contents printouts shorter than the value specified byDetermines what should control the page length Be extended, while longer documents will be divided into Fixed Document Mode Length P37 P38 Feeds 50 mm between black mark and cut Sets max black mark length to 5 mmSets min black mark length to 4 mm Add 30-mm top margin Do nothing when new page is printed. Auto-eject and retract Eject page when new page is printed. Retract disabledRetract page when new page is printed Will be retracted. Range 1-30, 1 step = 10 s No indication OffAutomatic Distance Calculation Paper Near End indication Default Parameter Settings Setup Printable Area N43 N44 Aligning Preprint And Thermal Print Recommended black mark size and position Setup Enables/disables black mark check Parameters Used Garbage, Black Mark and Out of Paper Detection Parameter n41 and n42 -Black Mark Cut Offset Specified by the ESC x command Send  Text and graphicsSend  RS Cuts and ejects the printout Simple Calibration Process Black-Mark Sensing from Within Windows Interface + Data Cable powerUSB Interface Cable ground Setup Options Serial Option, TTP Interface Maintenance Fault Finding Fault Finding 101 Cleaning The Print Head Printer with retract Fitting a Shutter Firmware Specifications Print Data None, Odd or Even Command Code Modes Non-Windows Applications Basic Character Set 108 109 Bar Codes Non-Windows Applications Paper Handling Printer Dimensions Environmental Conditions General Paper SpecificationMiscellaneous Thermal coating Perforation Preprinting Black Mark Size and Position Print can be expected within a zone of approximately 2-mmAround the edges of the hole. The function must be tested Accessories Part Number ListPrinters 116 117 Roll Holders Roll Holder for Paper Rolls up to 150 mm 119 120 中国 RoHS 材料声明 China RoHS Material Declaration 表示该部件的某一均质材料中的有毒有害物质的含量超出 SJ/Txxx-2006标准规定的限量要求。 122 Index Numerics Index Index Connector Port USBPage Zebra Technologies Europe Limited