Ryobi P545 manuel dutilisation General Maintenance

Page 19

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.

WARNING:

Toavoidseriouspersonalinjury,alwaysremovethe battery pack from the product when cleaning or performing any maintenance.

GENERAL MAINTENANCE

Before each use, inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until all missing or damaged parts are replaced. Please call 1-800-860-4050 or contact an authorized service center for assistance.

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at an Authorized Service Center.

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

WARNING:

Upon removal, cover the battery pack’s ter- minals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Lithium-ion and nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

19 - English

Image 19
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsSafety Apparel General Safety RulesSee Figures 1 KickbackGuide Bars CUTTING/WORK AreaBattery Safety Specific Safety RulesSymbol Signal Meaning SymbolsSymbol Name DESIGNATION/EXPLANATION Symbols See Figure FeaturesProduct Specifications Know Your ChainsawPacking List AssemblyOperation UnpackingApplications To Install / Remove Battery PackChain OIL System Preparation for Cutting Proper Grip on Handles Starting and Stopping the Chain SAWChain Line Tree Felling Basic Cutting ProcedureWork Area Precautions Proper Cutting StanceFall. See Figure See Figures 16 BuckingTypes of Cutting Used Bucking Logs Under StressSee Figures 18 Springpoles LimbingPruning General Maintenance MaintenanceRecommended BAR and Chain Combinations Replacing BAR and ChainSee Figures 23 See Figures 28 Chain TensionSee Figures 32 Chain MaintenanceHOW to Sharpen the Cutters See Figures 30See TOP Plate Filing AngleSide Plate Angle Depth Gauge ClearanceTransporting and Storing Guide BAR MaintenanceProblem Cause Solution TroubleshootingLimited Warranty Statement WarrantyVêtements DE Sécurité Règles DE Sécurité GénéralesAVERTISSEMENT  Lire Toutes LES Instructions Précautions ÉlémentairesVoir les figures 1 à RebondGuides Dans LA Zone DE COUPE/TRAVAILSécurité Pile Règles DE Sécurité ParticulièresAvertissement SymbolesSymbole Signal Signification Symbole NOM Désignation / Explication’approcher De 15 m 50 pi minimum Voir la figure CaractéristiquesFiche Technique Veiller À Bien Connaître LA Scie À ChaîneListe DE Contrôle D’EXPÉDITION AssemblageUtilisation DéballageApplications RETRAIT/INSTALLATION DU BLOC-PILES  AvertissementSystème DE Lubrification DE LA Chaîne Saisir Correctement LES Deux Poignées Démarrage ET Arrêt DE LA Scie À ChaînePréparation Pour LA Coupe Ligne DE Chaîne Précautions DE Chantier Position DE Coupe CorrecteAbattage D’ARBRES Méthode DE Coupe ÉlémentaireLigne DE Chute Prévue Débitage Débitage DE Billes Sous Contrainte Types DE Coupe UtilisésÉlagage ÉbranchageFouets Entretien Général EntretienCombinaisons DE Guide ET Chaîne Recommandées AVERTISSEMENT  Remplacement DU Guide ET DE LA ChaîneTension DE LA Chaîne Comment Affûter LES Dents Entretien DE LA ChaîneAngle DE Plaque Latérale Angle D’AFFÛTAGE DE LA Plaque SupérieureDégagement DE Jauge DE Profondeur Transport ET Remisage Entretien DU GuideDépannage Problème Cause SolutionÉnoncé DE LA Garantie Limitée GarantieAdvertencia Reglas DE Seguridad GeneralesRopa DE Seguridad Vea las figuras 1 y ContragolpeBarras Guía EN EL Área DE Corte O DE TrabajoSeguridad EN EL USO DEL Paquete DE Baterías Reglas DE Seguridad EspecíficasSímbolo Nombre Denominación / Explicación SímbolosSímbolo Señal Significado Peligro PrecauciónCon las alternativas de reciclado y desecho disponibles Vea la figura CaracterísticasEspecificaciones DEL Producto Familiarícese CON EL MotosierraLista DE Empaquetado ArmadoFuncionamiento DesempaquetadoVea la figura AplicacionesPara Desmontar Y Montar EL Paquete DE Baterías Sistema Lubricación DE LA CadenaPreparación Para EL Corte Sujeción Correcta DE LOS Mangos Encendido Y Apagado DE LA MotosierraVea las figuras 8 a Plano DE LA Cadena Tala DE Árboles Postura Correcta Para EL CorteProcedimiento Básico DE Corte Precauciones EN EL Área DE TrabajoEn la trayectoria de retirada planeada. Despeje una Vea las figuras 16 a TronzadoTipos DE Corte Efectuados Tronzado DE Troncos Bajo TensiónVea las figuras 18 y Pértigas DesramadoPoda Mantenimiento General MantenimientoCombinaciones DE Barra Y Cadena Recomendadas Reemplazo DE LA Barra Y DE LA CadenaVea las figuras 23 a Vea las figuras 28 y Tensión DE LA CadenaVea las figuras 32 y Mantenimiento DE LA CadenaForma DE Afilar LOS Dientes DE Corte Vea las figuras 30 yVea la figura 36 y Espacio Libre DEL Calibre DE ProfundidadÁngulo DE Limadura DE LA Placa Superior Ángulo DE LA Placa LateralTransporte Y Almacenamiento Mantenimiento DE LA Barra GuíaProblema Causa Solución Correción DE ProblemasDeclaración DE LA Garantía Limitada GarantíaPage Advertencia AVERTISSEMENT Techtronic Industries North AMERICA, INC