Ryobi RY28060 manuel dutilisation Attaching the Grass Deflector, Installing the String Head

Page 12

ASSEMBLY

Stop the engine and disconnect the spark plug wire.

Align the slot in the flanged washer with the slot in the gear head.

Place the gear head locking tool through the slot in the flanged washer and gear head.

Remove the blade nut by turning it clockwise.

Remove the cupped washer and the blade.

Remove the flanged washer from the gear head shaft and retain it for the string head installation.

Remove the three screws securing the brushcutter guard to gear head.

Remove the brushcutter guard.

NOTE: Store the brushcutter parts together for later use.

ATTACHING THE GRASS DEFLECTOR

See Figure 10.

WARNING:

The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury.

Stop the engine and disconnect the spark plug wire.

Remove the wing screw from the grass deflector.

Insert the tab on the mounting bracket in the slot on the grass deflector.

Align the screw hole in the mounting bracket with the screw hole in the grass deflector.

Insert the wing screw through the mounting bracket and into the grass deflector.

Tighten the screw securely.

INSTALLING THE STRING HEAD

See Figures 11 - 12.

Stop the engine and disconnect the spark plug wire.

Place the flanged washer on the gear head shaft.

NOTE: The hollow side of the flanged washer should face the gear head.

Align the slot in the flanged washer with the slot in the gear head.

Place the gear head locking tool through the slot in the flanged washer and gear head.

Place the arbor on the gear head. Then turn the arbor counter clockwise with a wrench to 120 in.lb. to tighten and install.

Place the string head assembly on the arbor. Make sure the opening on the string head assembly seats completely on the arbor. Install the spool retainer to secure.

Remove the plastic seal from the string head assembly. Pull outward on the strings to rotate the spool into the cutting position.

Push the spool retainer down while pulling on string(s) to manually advance the string and to check for proper assembly of the string head.

CONVERTING FROM STRING TRIMMER TO BRUSHCUTTER

To convert from the string trimmer to the brushcutter, remove the string head assembly and straight shaft grass deflector, attach the brushcutter guard and install the blade.

REMOVING THE STRAIGHT SHAFT GRASS DEFLECTOR AND STRING HEAD

See Figures 10 - 12.

Stop the engine and disconnect the spark plug wire.

Hold the string head and remove the spool retainer.

Remove the string head assembly.

Align the slot in the flanged washer with the slot in the gear head.

Place the gear head locking tool through the slot in the flanged washer and gear head.

Using a wrench, turn the arbor clockwise to loosen and remove.

Remove the flanged washer and retain it for the blade installation.

Remove the wing screw securing the grass deflector.

Remove the grass deflector.

NOTE: Store the string head parts together for later use.

INSTALLING THE TRI-ARC®BLADE AND BRUSHCUTTER GUARD

See Figure 9.

Stop the engine and disconnect the spark plug wire.

Install the brushcutter guard. Refer to Attaching the Brushcutter Guard earlier in this manual.

Place the flanged washer over the gear head shaft with the hollow side toward the brushcutter guard.

Center the blade on the flanged washer, making sure the blade fits flat and the raised hub of the flanged washer goes through the hole in the blade.

Install the cupped washer with the raised center away from the blade.

Place the blade nut onto the gear head shaft.

Place the gear head locking tool through the slot in the flanged washer and gear head.

Install the blade nut by turning it counterclockwise (left handed threads).

Tighten the blade nut securely and torque to 120 in.lb. minimum.

8 — English

Image 12
Contents Save this Manual for Future Reference Toutes LES Versions Todas LAS VersionesREEL-EASY Seguro del gatilloProper Brush Cutter Operating Position IiiDirection of rotation sens de rotation, sentido de rotación Latch loquet, pestillo Eyelet oeillet, ojillo Table of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules Specific Safety Rules for Trimmer USESpecific Safety Rules for ­ Brushcutter and Blade USE Symbols Symbol Signal MeaningSymbol Name Explanation Features AssemblyInstalling the Power Head to the Attachment Removing the Attachment from the Power HeadAttaching the Storage Hanger Attaching the J HandleInstalling the String Head Installing the TRI-ARCBLADE and Brushcutter GuardAttaching the Grass Deflector Converting from String Trimmer to BrushcutterOperation Fueling and Refueling the ToolOxygenated Fuels Operating the BrushcutterBlade Thrust TRI-ARCBLADECutting Technique Blade Operating the TrimmerMaintenance Cutting TipsGrass Deflector Line Trimming CUT-OFF Blade Starting and StoppingGeneral Maintenance Spool Replacement REEL-EASY TAP Advance SystemLine Replacement Installing Dual Spool Fixed Line String Head InsertCleaning the Exhaust Port and Muffler Spark Arrestor Idle Speed AdjustmentCleaning AIR Filter Screen Spark Plug ReplacementTroubleshooting Gap. Refer to Spark Plug Replacement earlierSpeed. See Figure Warranty This Product WAS Manufactured with a Catalyst MufflerLimited Warranty Statement MANUFACTURER’S Warranty Coverage Règles DE Sécurité Générales AvertissementLire Toutes LES Instructions Règles DE Sécurité Particulières Symboles Symbole NOM ExplicationCaractéristiques AssemblageInstallation DU BLOC-MOTEUR SUR L’ACCESSOIRE Retrait DE L’ACCESSOIRE DU Bloc MoteurInstallation DE L’ANNEAU DE Suspension Installation DE LA Poignée EN « J »Installation DU Déflecteur D’HERBE Installation DE LA Tête DE Coupe À LigneInstallation DE LA Lame TRI-ARCET DU PARE-DÉBRIS Conversion DE TAILLE-BORDURES EN DébroussailleuseUtilisation Approvisionnement EN CarburantCarburants Oxygénés Utilisation DE LA DébroussailleuseRicochet DE Lame Lame TRI-ARCTechniques DE Coupe Lame Utilisation DU TAILLE-BORDURESEntretien Conseils DE CoupeDémarrage ET Arrêt AVERTISSEMENT Remplacement DE Ligne Installation DE LA Bobine À FIL Fixe Dual SpoolEntretien Général Réglage DU Ralenti Nettoyage DU Filtre À AIR ÉcranBouchon DU Réservoir Avertissement Remisage LE ProduitDépannage Nettoyage du filtre à air écran, plus haut dansGarantie ’AIDE?Fonctionnement Chaque année Énoncé DE LA Garantie Limitée Responsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Reglas DE Seguridad Generales AdvertenciaLEA Todas LAS Instrucciones Reglas DE Seguridad Específicas Symbolo Nombre Explicatión PeligroPrecaución Símbolo Señal SignificadoCaracterísticas ArmadoInstalación DEL Cabezal Motor EN EL Aditamento Desmontaje DEL Aditamento DEL Cabezal MotorMontaje DE LA ASA DE ALMACENAMIENTO Montaje DEL Mango EN JInstalación DEL Deflector DE Pasto Instalación DEL Cabezal DEL HiloConversión DE Recortadora DE Hilo a Desbrozadora Funcionamiento Abastecimiento DE CombustibleCombustibles Oxigenados Utilización DE LA DesbrozadoraContragolpe DE LA Cuchilla Cuchilla TRI-ARCTécnica DE Corte CON Cuchilla Utilización DE LA RectodoraMantenimiento Sugerencias Para CortarCuchilla DE Corte DEL Hilo EN EL Deflector DE Hierba Arranque Y ApagadoMantenimiento General Reabastecimiento DEL HiloVea las figures 21 Vea las figures 23Limpieza DEL Orificio DE Escape Y DEL Silenciador ParachispasLimpieza DEL Filtro DE Aire Pantalla Tapa DEL Tanque DE Combustible AdvertenciaSolución DE Problemas Vea la figuraGarantía Conjunto DE Silenciador Catalítico4050 Declaración DE LA Garantía Limitada Cobertura DE LA Garantía DEL Fabricante Manuel D’UTILISATION / Manual DEL Operador Débroussailleuse DE 26 CC  Desbrozadora 26 CC