Porter-Cable D28733-034-0, PGN350 Wattage Calculations, Determining Wattage Requirements, Total

Page 17

WATTAGE CALCULATIONS

IMPORTANT

Never exceed the rated capacity of your generator. Serious damage to the generator or appliance could result from an overload.

1.Starting and running wattage requirements should always be calculated when matching a generators wattage capacity to the appliance or tool.

2.There are two types of electrical appliances that can be powered by your generator:

A.Items such as radios, light bulbs, television sets, and microwaves have a "resistive load". Starting wattage and running wattage are the same.

B.Items such as refrigerators, air compressors, washer, dryer, and hand tools that use an electrical motor have an "inductive load". Inductive load appliances and tools require approximately 2 to 4 times the listed wattage for starting the equipment. This initial load only lasts for a few seconds on start-up but is very important when figuring your total wattage to be used.

C.Always start your largest electric motor first, and then plug in other items, one at a time.

NOTE: On 120-volt loads the maximum starting wattage should NOT

exceed one half of the rated generator wattage. Example: a 5000 rated wattage generator = 2500 maximum starting wattage.

DETERMINING WATTAGE REQUIREMENTS

Before operating this generator list all of the appliances and/or tools that are going to operate at the same time. (Then determine the starting wattage requirements and the running wattage requirements by following example and/or refer to household wattage calculator.)

1.First total the running wattage of all appliances and/or tools that will be operated at the same time.

 

 

Running Watts

Starting Watts

Example 1:

 

 

 

 

Lights

=

100 Watts

0

Television

=

300 Watts

0

Slow Cooker

=

250 Watts

 

0

 

TOTAL

=650 Watts

0

2.Next the starting wattages of any appliances and/or tools that will start and stop during operation.

 

Running Watts

Starting Watts

Example 2:

 

 

Small Refrigerator

500 Watts

2000 Watts

TOTAL

=500 Watts

2000 Watts

3.The running wattage of examples 1 & 2 totals 1150 watts. The starting wattage of the small refrigerator is 2000 watts which is 1500 watts more than the running watts. Take this difference of 1500 starting watts from the refrigerator and add to the total running watts of 1150.

Example 3:

1500

Starting Watts

 

1150

Running Watts

TOTAL

=2650 Total Watts

Generator must have a maximum capacity of at least 2650 watts.

17- ENG

D28733

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Generator Consumer Safety Information Consumer General and Service InformationImportant Safety Instructions Safety Guidelines / DefinitionsWhen installing a Double Risk of Electrocution and FireRisk of Electrocution and Fire When damagedOperation Generator in rainConfined Area Risk of FireUnit Indoors or in ANY Risk of Unsafe Operation Risk of Breathing Inhalation HazardRisk of HOT Surfaces Risk from Lifting SpecificationsRisk of Moving Parts Remove Generator from Carton AssemblyOther Loose Parts Extension Cord Wrap Forms and Protective BARHandle Rubber BumperGrounding the Generator Double Throw Transfer SwitchObtaining Electricity from the Generator Extension CordsOperation To Start the Engine Stopping Engine Connecting Electrical LoadsEngine Maintenance MaintenanceGenerator Maintenance Customer Responsibilities TableGenerator StorageEngine Preparation Total Wattage CalculationsDetermining Wattage Requirements Starting Wattage Requirements Application GuideAppliance or Load Device Typical Device Wattage Total Household Wattage CalculatorStart Troubleshooting GuideResponsibility of Original Purchaser initial User Limited WarrantyQuick Facts Modelo GeneradoresInformación General Y DE Servicio Riesgo ¿QUÉ Puede OCURRIR? ¿CÓMO PREVENIRLO? Pautas DE SEGURIDAD/DEFINICIONESInstrucciones Importantes DE Seguridad Riesgo DE Incendio Y Electrocución continuación SubdimensionadosOperación del Generador bajoTanque de com Intentar llenar elBustible mientras El motor está enInhalación, daños a IncendioLas superficies del VehículoOperación de Riesgo DE Operación Insegura continuaciónEquipos sensibles Las fluctuacionesTabla DE Especificaciones Sacar EL Generador DE LA Caja InstalaciónOtras Partes Sueltas Colgador Para Cordón DE Extensión Y Barra ProtectoraHandle Tope DE CauchoAbasteciéndose DE Electricidad DEL Generador Conexión a Tierra DEL GeneradorCables DE Extensión Eléctrica Interruptor DE Transferencia DE Doble HojaCapacidad DEL Generador Familiarizarse CON EL GeneradorInterruptores DE Circuito Dispositivo DE Apagado POR Poco AceiteAntes de arrancar el generador Arranque Manual DEL MotorParando EL Motor Cartilla DE Responsabilidades DEL Cliente Programa DE MantenimientoRecomendaciones Generales Mantenimiento DEL MotorGenerador AlmacenajePreparación DEL Motor Vatios de Funcionamiento ImportanteDeterminando LOS Requerimientos DE Potencia Volts X Ampers = Vatios Volts x 10 ampers = 1 200 W Potencia Requerida Para EL ArranqueCalculo DE Potencia Doméstica PrecaucionProblema Causa Corrección Guía Para Diagnóstico DE ProblemasResponsabilidad DEL Comprador Original Usuario inicial Garantía LimitadaMotor Almacenaje Operación Informacion Rapida Sobre GeneradoresGasolina Para EL Motor Aceite Potencia Cableado Batería Y Manuel Renseignements Pour LE Consommateur Risques Délectrocution ET D’INCENDIE Mesures DE Sécurité DéfinitionsMesures DE Sécurité Importantes Risque Risques Délectrocution ET D’INCENDIE suiteRisques D’INCENDIE Risques D’UNE Utilisation Risques AUX Voies Respiratoires ET Risques D’INHALATIONRisques Reliés AUX Surfaces Chaudes Risques Lors DU Levage SpécificationsRisques Reliés AUX Pièces Mobiles Autres Pièces Détachées Retrait DE LA Génératrice DE SON EmballageDévidoirs DE Rallonge ET Barre Protectrice Fonctionnement et de l’entretien du Guide de l’utilisateurPoignée PARE-CHOCS EN CaoutchoucComment Obtenir DE L’ÉLECTRICITÉ DE LA Génératrice Mise À LA Terre DE LA GénératriceRallonges Inverseur BidirectionnelBien Connaître Votre Génératrice UtilisationCapacité DE LA Génératrice COUPE-CIRCUITFaçon permanente les appareils branchés Démarrage DU MoteurArrêt DU Moteur Entretien Recommandations GénéralesTableau DES Responsabilités DU Client Entretien DU MoteurGénératrice EntreposagePréparation DU Moteur Détermination DES Exigences DE Puissance EN Watts Puissance de serviceCalcul DE LA Puissance EN Watts Volts x ampères = watts Volts x 10 ampères = 1 200 watts Puissance D’AMORÇAGE EN WattsCalcul DE LA Puissance EN Watts Mise EN GardeProblème Cause Correction Guide DE DépannageResponsabilité DE Lacheteur Dorigine utilisateur initial Garantie LimitéeRemarque 67- FR D28733 Toujours Consulter LES Guides Fournis Avec CET Appareil Faits Saillants

D28733-034-0, PGN350 specifications

The Porter-Cable D28733-034-0, PGN350 is a versatile and robust tool designed for professionals and DIY enthusiasts who demand high-performance tools in their projects. This pneumatic nail gun is engineered for reliability and precision, making it a popular choice in the construction and woodworking industries.

One of the main features of the PGN350 is its lightweight design, which enhances portability and ease of use. Weighing in at just a few pounds, operators can maneuver this tool comfortably for extended periods, reducing fatigue during long job sessions. Additionally, its durable construction ensures it can withstand the rigors of job site conditions.

Equipped with a powerful motor, the PGN350 delivers exceptional driving force, allowing it to effortlessly handle a range of fasteners, including 1-1/4 inch to 3-1/2 inch collated framing nails. This versatility makes it suitable for various applications, including framing, decking, and other structural tasks. The tool’s depth adjustment feature provides improved control over nail depth, ensuring a professional finish even on varying materials.

The PGN350 incorporates advanced technologies that enhance user experience and performance. Its rapid-fire mode allows for quick and efficient nailing, which is an essential feature for projects requiring high productivity. Moreover, the tool is designed with a tool-free jam release mechanism, making it easy to clear nail jams without the need for additional tools, thus minimizing downtime.

Safety is also a priority with the PGN350. It comes equipped with a trigger lock-off feature, which prevents accidental firing, offering peace of mind when the tool is not in use. This safety mechanism is fundamental for maintaining workplace safety, particularly in busy construction environments.

The unit features a comfortable grip and an ergonomic design that provides stability and control, reducing the risk of wrist strain and enhancing overall efficiency. The tool's air inlet is compatible with standard air hoses, making it easy to integrate into existing pneumatic tool systems.

In summary, the Porter-Cable D28733-034-0, PGN350 stands out for its lightweight design, powerful performance, and user-friendly features. Its advanced technologies, safety mechanisms, and versatility make it an essential tool for anyone looking to accomplish professional-grade results in their woodworking or construction projects. Whether you are framing a house or building furniture, the PGN350 is built to deliver reliability and precision every time.
Top Page Image Contents