Lexicon SDP-40 manual Understanding the Zones

Page 31

SDP-40

Basic Operation

UNDERSTANDING THE ZONES

The SDP-40 features three zones: the Main Zone, Zone 2, and the Record Zone. The Main Zone is designed to control audio and video signals in the primary listening space, Zone 2 is designed to control audio signals in the secondary listening space, and the Record Zone is designed to control audio and video signals for recording devices. The Record Zone can also function as a third zone, controlling audio and video signals in a third listening space.

All three zones utilitize separate digital audio receivers, analog-to- digital converters, and digital-to-analog converters. This allows independent input selection in each zone with most input types. For instance, the unit can play a DVD in the Main Zone, play a CD in Zone 2, and send signals from a satellite receiver to a VCR through the Record Zone - all at the same time.

The following exceptions apply to independent zone function:

The same Dolby Digital or dts(-ES) input type can be selected in all zones simultaneously. However, when a Dolby Digital or dts(-ES) input type is active in the Main Zone, a different Dolby Digital or dts(-ES) input type cannot be active in Zone 2 or the Record Zone.

Zone 2 and the Record Zone will provide a downmix (a 2-channel version of multi-channel digital audio) only when using the same input that is selected in the Main Zone.

Use caution when switching from a Dolby Digital input type to a dts(-ES) input type in the Record Zone. A loud, brief noise may occur.

Audio will mute for up to 2 seconds when:

-The same input is selected in the Main Zone that is already selected in Zone 2 or the Record Zone. Likewise, when the input is deselected in the Main Zone.

-The same input is selected in Zone 2 or the Record Zone that is already selected in the Main Zone. Likewise, when the input is deselected in Zone 2 or the Record Zone.

When the 5.1 BYPASS listening mode is selected for the Main Zone, the same input can be utilized by Zone 2 or the Record Zone. However, only the FRONT L/R input signals will be available.

2-15

Image 31
Contents SDP-40 Important Safety Instructions JBL Synthesis Introduction Audio Controls Menu Instruções DE Segurança IMPORTANTEs PortugueseEspañol Instrucciones Importantes DE Seguridad DeutschItaliano Importanti Norme DI Sicurezza Français Instructions DE Sûreté ImportantesSuomi Dansk Vigtig Information OM SikkerhedNorsk Viktig Informasjon OM Sikkerhet US Unpacking and Inspection Getting Started Getting Started Highlights Navigating the Menus Using the DocumentationUser Guide Symbols Location ConsiderationsTWO-LINE Status Restoring FACTORY-DEFAULT SettingsExit Basic Operation IR Receiver Front PanelBlue LED Main Off deactivates the Main Zone Basic Operation Basic Operation Rear Panel Command Bank Selection Remote ControlBank Selection BankStandby LightSelection Buttons InputOSD BlueVOL + Mode +Mute StatMenu 2CH ArrowsFamily ModeUnderstanding the Zones Music Understanding Listening Mode SelectionInput Setup Menu Mode ButtonsChannel Digital Mode Family Selection ButtonsSetup Menu Displays SetupVolume Controls Rear Panel ConfigDVD1 Input SetupName Restore Default NameName Digital COAX-1 DigitalAuto Default Parameter Value ValuesAnalog Anlg in LVLAnlg in LVL Auto ManualVideo VideoComponent Inputs Dts-ESFilm Main Advanced ZONE2 Advanced Record Advanced DVD1 D Mode Main Advanced Analog Bypass ON, OFF Input Select AUTO, ANALOG, DigitalVideo Main AdvancedZONE2 Advanced Component OSD ON, OFFAnalog Input SelectRecord Advanced Record Anlg in LVLDigital Bypass ON, OFF DIG OUT RateDetermining Crossover Settings Speaker Setup Custom SetupLowpass Filter Frequency Response CurvesCenter Custom SetupFront L/R FULL, 30Hz to 120Hz, THX 80HzSide L/R Side L/RFULL, 30Hz to120Hz, THX 80Hz, None Rear L/RSUB Xover SUB L/RSUB Xover SUB L/RLFE OFF LFE ON, OFFDefault Synthesis 7CH SetupParameter Value Values Speaker Distances SetupInternal Noise Test Levels CalibrationDacs Calibration Dacs Calibration Levels CalibrationSUB Limiters LFE Limiter ON, OFF CAL Noise ON, OFFLimiter ON, OFF Limit ADJStereo & 5.1 Anlg Stereo InputsStatus Display Setup ON-SCREEN DisplayPosition ON-SCREEN Display Sync DelayFront Panel Display Custom Name OFF Edit Custom NameCustom Name Edit Custom NameZone PWR on Volume Control SetupMain PWR on Mute LevelTrigger Trigger SetupRemote Operation Program OperationLock Options SetupModes Audio CntrlAudio Controls Menu Bass Audio ControlsAudio Controls Bass Audio Controls Tilt EQ TrebleAudio Controls Treble Tilt EQAudio Controls ZONE2 Balance Loudness ON, OFF Audio ControlsAudio Controls Balance Audio Controls FaderAudio Controls Record Balance Record BalanceMode Adjust Menu Listening Mode Descriptions LOGIC7 Film Mode AdjustMode Adjust L7 Film LOGIC7 Music Mode Adjust L7 TVMode Adjust Music LOGIC7 TVDolby PRO Logic Mode Adjust PLMode Adjust L7 PRO Logic Dolby PRO Logic II THXDefault Parameter Values Default Value Mode Adjust L7 PL II MusicDolby PRO Logic II Music Party Mode Adjust 2-CHANNELMode Adjust Party ChannelMono Mode Adjust MonoDefault ParameterValueValues Mode Adjust Mono LogicMode Adjust 5.1L7 Film Mode Adjust Mono SurroundMono Surround Mode Adjust 5.1L7 Music Mode Adjust 5.1L7 TVTHX Mode Adjust 5.1 SUR EXTHX Surround EX or 5.1 THX THX Surround EX2-CHANNEL Mode Adjust L7 DigitalMode Adjust 5.1 2-CHANNEL Dolby DigitalMode Adjust 5.1 Mono Logic Mode Adjust 5.1 MonoMono Dts-ES LOGIC7 film Mode Adjust 5.1 Mono SurrDts-ES LOGIC7 Music Mode AdjustDts-ES THX Dts Mode Adjust 2-CHANDts and dts-ES Dts-ES 2-CHANNELChannel Bypass Mode Adjust 5.1 BypassMode Adjust 2CH Bypass BypassCustom Custom VS PresetReset Mode Output LevelsParameter Values Status Menus2CH Status Menu 2CH Bypass Status MenuBypass Status Menu Dolby Digital Status MenuAnalog Status Menu Academy Filter ON, OFF Mode Parameter DescriptionsDts Status Menu Spkr Enhance ON, OFFCntr DLY Samples Bass Enhance ON, OFFCenter MIX ChannelsEffect LVL DimensionCTR Width CustomOutput Levels LFE MIXMaster Level ModeSurround EX ON, OFF Sound StageSurr Rolloff Surround DLYTroubleshooting and Maintenance Troubleshooting If ALL Else Fails Humming Sound is Present in the AudioRF Interference is Present in the Audio or Video Unit is Exhibiting Erratic BehaviorRoutine Maintenance Appendix Performance Zone 2 and Record Zone SpecificationsAudio Inputs and Outputs Performance Main ZoneOther Video Inputs and OutputsPerformance Composite & S-video Performance Component VideoDeclaration of Conformity On page A-6 Menu TreeFrom page A-5 DVD1 Input Setup Name None Side L/R Speakers Dacs Calibration Film Auto Azimuth Input Type BYP Additional Listening Mode MenusInput Setup Installation WorksheetRear Panel Config Index Index Name Tilt EQ Synthesis Limited Warranty JBL Synthesis