Lexicon SDP-40 manual Rear Panel

Page 22

Basic Operation

JBL

REAR PANEL (continued)

11The MICROPHONE INPUTS are provided for future expansion. Four 3.5mm T/R/S or balanced inputs are available.

12The TRIGGER OUTPUTS provide DC output. These outputs are available on a 5-pin DIN connector. The PWR trigger is on when the unit is on, and off when the unit is in standby or off. Triggers 1 and 2 can be configured in the TRIGGER SETUP menu (see page 3-35). The default trigger settings are preconfigured for use in JBL Synthesis systems with switching transducers for cinema and music modes.

GROUND

TRIGGER 2

TRIGGER 1

GROUND

POWER TRIGGER

13The RS-232 Connector labelled 1 is provided for serial control and software upgrades. The RS-232 connector labelled 2 is provided for future expansion.

14The IR IN Connector is provided for input of infrared data from industry-standard infrared distribution equipment. A 3.5mm T/R/S input is available.

15A Removable Access Panel is provided for future expansion.

2-6

Image 22

Contents SDP-40 Important Safety Instructions JBL Synthesis Introduction Audio Controls Menu Portuguese Instruções DE Segurança IMPORTANTEsDeutsch Español Instrucciones Importantes DE SeguridadFrançais Instructions DE Sûreté Importantes Italiano Importanti Norme DI SicurezzaDansk Vigtig Information OM Sikkerhed SuomiNorsk Viktig Informasjon OM Sikkerhet US Unpacking and Inspection Getting Started Getting Started Highlights Location Considerations Using the DocumentationUser Guide Symbols Navigating the MenusTWO-LINE Status Restoring FACTORY-DEFAULT SettingsExit Basic Operation IR Receiver Front PanelBlue LED Main Off deactivates the Main Zone Basic Operation Basic Operation Rear Panel Remote Control Command Bank SelectionLight BankStandby Bank SelectionInput Selection ButtonsBlue OSDMode + VOL +Mute StatMenu Arrows 2CHMode FamilyUnderstanding the Zones Mode Buttons Understanding Listening Mode SelectionInput Setup Menu MusicMode Family Selection Buttons Channel DigitalSetup Menu Rear Panel Config SetupVolume Controls DisplaysInput Setup DVD1Name Restore Default NameName Digital Digital COAX-1Anlg in LVL Default Parameter Value ValuesAnalog AutoManual Anlg in LVL AutoVideo VideoComponent Inputs Dts-ESFilm Main Advanced ZONE2 Advanced Record Advanced DVD1 D Mode Main Advanced Input Select AUTO, ANALOG, Digital Analog Bypass ON, OFFComponent OSD ON, OFF Main AdvancedZONE2 Advanced VideoInput Select AnalogRecord Advanced DIG OUT Rate Anlg in LVLDigital Bypass ON, OFF RecordSpeaker Setup Custom Setup Determining Crossover SettingsFrequency Response Curves Lowpass FilterFULL, 30Hz to 120Hz, THX 80Hz Custom SetupFront L/R CenterRear L/R Side L/RFULL, 30Hz to120Hz, THX 80Hz, None Side L/RSUB L/R SUB L/RSUB Xover SUB XoverLFE ON, OFF LFE OFFDefault Synthesis 7CH SetupParameter Value Values Setup Speaker DistancesLevels Calibration Internal Noise TestDacs Calibration Dacs Calibration Levels CalibrationSUB Limiters Limit ADJ CAL Noise ON, OFFLimiter ON, OFF LFE Limiter ON, OFFStereo Inputs Stereo & 5.1 AnlgStatus Display Setup ON-SCREEN DisplayPosition ON-SCREEN Display Sync DelayFront Panel Display Edit Custom Name Edit Custom NameCustom Name Custom Name OFFMute Level Volume Control SetupMain PWR on Zone PWR onProgram Operation Trigger SetupRemote Operation TriggerAudio Cntrl SetupModes Lock OptionsAudio Controls Menu Bass Audio ControlsAudio Controls Bass Tilt EQ TrebleAudio Controls Treble Audio Controls Tilt EQAudio Controls Fader Loudness ON, OFF Audio ControlsAudio Controls Balance Audio Controls ZONE2 BalanceRecord Balance Audio Controls Record BalanceMode Adjust Menu Listening Mode Descriptions LOGIC7 Film Mode AdjustMode Adjust L7 Film LOGIC7 TV Mode Adjust L7 TVMode Adjust Music LOGIC7 MusicDolby PRO Logic II THX Mode Adjust PLMode Adjust L7 PRO Logic Dolby PRO LogicDefault Parameter Values Default Value Mode Adjust L7 PL II MusicDolby PRO Logic II Music Channel Mode Adjust 2-CHANNELMode Adjust Party PartyMode Adjust Mono Logic Mode Adjust MonoDefault ParameterValueValues MonoMode Adjust 5.1L7 Film Mode Adjust Mono SurroundMono Surround Mode Adjust 5.1L7 TV Mode Adjust 5.1L7 MusicTHX Surround EX Mode Adjust 5.1 SUR EXTHX Surround EX or 5.1 THX THXDolby Digital Mode Adjust L7 DigitalMode Adjust 5.1 2-CHANNEL 2-CHANNELMode Adjust 5.1 Mono Logic Mode Adjust 5.1 MonoMono Mode Adjust 5.1 Mono Surr Dts-ES LOGIC7 filmDts-ES LOGIC7 Music Mode AdjustDts-ES THX Dts-ES 2-CHANNEL Mode Adjust 2-CHANDts and dts-ES DtsBypass Mode Adjust 5.1 BypassMode Adjust 2CH Bypass Channel BypassOutput Levels Custom VS PresetReset Mode Custom2CH Bypass Status Menu Status Menus2CH Status Menu Parameter ValuesBypass Status Menu Dolby Digital Status MenuAnalog Status Menu Spkr Enhance ON, OFF Mode Parameter DescriptionsDts Status Menu Academy Filter ON, OFFChannels Bass Enhance ON, OFFCenter MIX Cntr DLY SamplesCustom DimensionCTR Width Effect LVLMode LFE MIXMaster Level Output LevelsSurround DLY Sound StageSurr Rolloff Surround EX ON, OFFTroubleshooting and Maintenance Troubleshooting Unit is Exhibiting Erratic Behavior Humming Sound is Present in the AudioRF Interference is Present in the Audio or Video If ALL Else FailsRoutine Maintenance Appendix Performance Main Zone SpecificationsAudio Inputs and Outputs Performance Zone 2 and Record ZonePerformance Component Video Video Inputs and OutputsPerformance Composite & S-video OtherDeclaration of Conformity Menu Tree On page A-6From page A-5 DVD1 Input Setup Name None Side L/R Speakers Dacs Calibration Film Auto Azimuth Additional Listening Mode Menus Input Type BYPInstallation Worksheet Input SetupRear Panel Config Index Index Name Tilt EQ Synthesis Limited Warranty JBL Synthesis