Lexicon SDP-40 manual Stereo Inputs, Stereo & 5.1 Anlg

Page 63

The SETUP Menu

JBL

MAIN MENU

MODE ADJUST AUDIO CONTROLS

SETUP

SETUP

INPUTS

SPEAKERS

REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGERS

LOCK OPTIONS

REAR PANEL CONFIG

8 STEREO INPUTS OR

5 STEREO & 5.1 ANLG

Note:

If 5 STEREO & 5.1 ANLG is selected on the REAR PANEL CONFIG menu, the unit will automatically select the 5.1 BYPASS listening mode if the following conditions are also met:

The ANALOG IN parameter on the INPUT SETUP menu is set to 5.1 ANALOG (see page 3-6).

The INPUT SELECT parameter on the MAIN ADV menu is set to either AUTO or ANALOG (see page 3-13). When set to AUTO, no digital input types can be present.

The ANALOG BYPASS parameter on the MAIN ADV menu is set to ON (see page 3-13).

REAR PANEL CONFIG

The REAR PANEL CONFIG menu can be used to configure AUDIO INPUT pairs 1 to 8 on the rear panel. These inputs can be set up to function as eight stereo analog input pairs, or as five stereo analog input pairs and one 5.1-channel analog input.

8 STEREO INPUTS

SETUP REAR PANEL CONFIG 8 STEREO INPUTS

8 STEREO INPUTS is the default setting for REAR PANEL CONFIG. When set to 8 STEREO INPUTS, the AUDIO INPUTS are configured as eight stereo analog input pairs. Pairs 6, 7, and 8 are not available as a 5.1-channel analog input. Input types that are assigned to the 5.1-channel analog input will be reassigned to stereo input Pair 6.

5 STEREO & 5.1 ANLG

SETUP

REAR PANEL CONFIG

5 STEREO & 5.1 ANLG

When set to 5 STEREO & 5.1 ANLG, the AUDIO INPUTS are configured as five stereo analog input pairs and one 5.1-channel analog input. The 5.1-channel analog input consists of AUDIO INPUT pairs 6, 7, and 8. Pair 6 becomes the front left and right (L)/(R) inputs. Pair 7 becomes the center (C) and subwoofer (SUB) inputs. And Pair 8 becomes the surround left and right (LS)/(RS) inputs. Input types that are assigned to stereo analog input pairs 6, 7, and 8 will be reassigned to the 5.1-channel analog input.

When selected for the Main Zone, these input signals are sent to the corresponding outputs. However, neither Zone 2 nor the Record Zone provide multi-channel outputs. If the 5.1-channel analog input is selected for Zone 2 or the Record Zone, only the front left and right (L)/(R) inputs will be available.

3-30

Image 63
Contents SDP-40 Important Safety Instructions JBL Synthesis Introduction Audio Controls Menu Instruções DE Segurança IMPORTANTEs PortugueseEspañol Instrucciones Importantes DE Seguridad DeutschItaliano Importanti Norme DI Sicurezza Français Instructions DE Sûreté ImportantesSuomi Dansk Vigtig Information OM SikkerhedNorsk Viktig Informasjon OM Sikkerhet US Unpacking and Inspection Getting Started Getting Started Highlights Navigating the Menus Using the DocumentationUser Guide Symbols Location ConsiderationsRestoring FACTORY-DEFAULT Settings TWO-LINE StatusExit Basic Operation Front Panel IR ReceiverBlue LED Main Off deactivates the Main Zone Basic Operation Basic Operation Rear Panel Command Bank Selection Remote ControlBank Selection BankStandby LightSelection Buttons InputOSD BlueVOL + Mode +Stat MuteMenu 2CH ArrowsFamily ModeUnderstanding the Zones Music Understanding Listening Mode SelectionInput Setup Menu Mode ButtonsChannel Digital Mode Family Selection ButtonsSetup Menu Displays SetupVolume Controls Rear Panel ConfigDVD1 Input SetupRestore Default Name NameName Digital COAX-1 DigitalAuto Default Parameter Value ValuesAnalog Anlg in LVLAnlg in LVL Auto ManualVideo VideoComponent Dts-ES InputsFilm Main Advanced ZONE2 Advanced Record Advanced DVD1 D Mode Main Advanced Analog Bypass ON, OFF Input Select AUTO, ANALOG, DigitalVideo Main AdvancedZONE2 Advanced Component OSD ON, OFFAnalog Input SelectRecord Advanced Record Anlg in LVLDigital Bypass ON, OFF DIG OUT RateDetermining Crossover Settings Speaker Setup Custom SetupLowpass Filter Frequency Response CurvesCenter Custom SetupFront L/R FULL, 30Hz to 120Hz, THX 80HzSide L/R Side L/RFULL, 30Hz to120Hz, THX 80Hz, None Rear L/RSUB Xover SUB L/RSUB Xover SUB L/RLFE OFF LFE ON, OFFSynthesis 7CH Setup DefaultParameter Value Values Speaker Distances SetupInternal Noise Test Levels CalibrationDacs Calibration Levels Calibration Dacs CalibrationSUB Limiters LFE Limiter ON, OFF CAL Noise ON, OFFLimiter ON, OFF Limit ADJStereo & 5.1 Anlg Stereo InputsDisplay Setup ON-SCREEN Display StatusPosition Sync Delay ON-SCREEN DisplayFront Panel Display Custom Name OFF Edit Custom NameCustom Name Edit Custom NameZone PWR on Volume Control SetupMain PWR on Mute LevelTrigger Trigger SetupRemote Operation Program OperationLock Options SetupModes Audio CntrlAudio Controls Menu Audio Controls BassAudio Controls Bass Audio Controls Tilt EQ TrebleAudio Controls Treble Tilt EQAudio Controls ZONE2 Balance Loudness ON, OFF Audio ControlsAudio Controls Balance Audio Controls FaderAudio Controls Record Balance Record BalanceMode Adjust Menu Mode Adjust Listening Mode Descriptions LOGIC7 FilmMode Adjust L7 Film LOGIC7 Music Mode Adjust L7 TVMode Adjust Music LOGIC7 TVDolby PRO Logic Mode Adjust PLMode Adjust L7 PRO Logic Dolby PRO Logic II THXMode Adjust L7 PL II Music Default Parameter Values Default ValueDolby PRO Logic II Music Party Mode Adjust 2-CHANNELMode Adjust Party ChannelMono Mode Adjust MonoDefault ParameterValueValues Mode Adjust Mono LogicMode Adjust Mono Surround Mode Adjust 5.1L7 FilmMono Surround Mode Adjust 5.1L7 Music Mode Adjust 5.1L7 TVTHX Mode Adjust 5.1 SUR EXTHX Surround EX or 5.1 THX THX Surround EX2-CHANNEL Mode Adjust L7 DigitalMode Adjust 5.1 2-CHANNEL Dolby DigitalMode Adjust 5.1 Mono Mode Adjust 5.1 Mono LogicMono Dts-ES LOGIC7 film Mode Adjust 5.1 Mono SurrMode Adjust Dts-ES LOGIC7 MusicDts-ES THX Dts Mode Adjust 2-CHANDts and dts-ES Dts-ES 2-CHANNELChannel Bypass Mode Adjust 5.1 BypassMode Adjust 2CH Bypass BypassCustom Custom VS PresetReset Mode Output LevelsParameter Values Status Menus2CH Status Menu 2CH Bypass Status MenuDolby Digital Status Menu Bypass Status MenuAnalog Status Menu Academy Filter ON, OFF Mode Parameter DescriptionsDts Status Menu Spkr Enhance ON, OFFCntr DLY Samples Bass Enhance ON, OFFCenter MIX ChannelsEffect LVL DimensionCTR Width CustomOutput Levels LFE MIXMaster Level ModeSurround EX ON, OFF Sound StageSurr Rolloff Surround DLYTroubleshooting and Maintenance Troubleshooting If ALL Else Fails Humming Sound is Present in the AudioRF Interference is Present in the Audio or Video Unit is Exhibiting Erratic BehaviorRoutine Maintenance Appendix Performance Zone 2 and Record Zone SpecificationsAudio Inputs and Outputs Performance Main ZoneOther Video Inputs and OutputsPerformance Composite & S-video Performance Component VideoDeclaration of Conformity On page A-6 Menu TreeFrom page A-5 DVD1 Input Setup Name None Side L/R Speakers Dacs Calibration Film Auto Azimuth Input Type BYP Additional Listening Mode MenusInput Setup Installation WorksheetRear Panel Config Index Index Name Tilt EQ Synthesis Limited Warranty JBL Synthesis