American Dryer Corp ADG-60 service manual To Remove Control Box, To Remove Front Panel

Page 10

D. To Remove Control Box

1.Discontinue power to the dryer.

2.Remove the lint drawer and the control door from the dryer. Follow lint drawer, and control and lint door removal procedures in sections A and B.

3.Remove screw located on the bottom right-hand corner of the control panel.

4.Slide out the control box and hang the control box assembly on hinges located on the right side panel, and disconnect the three (3) wiring harnesses (connectors) at the back of the control box.

5.The control box may now be taken out of the dryer completely or depending on the service function to be performed, the box can be attached to the two (2) female hinges on the right side

of the dryer cabinet.

NOTE: If the control box is attached to the dryer cabinet, the three (3) wiring harnesses men- tioned in step #4 do not need to be disconnected.

6.Reverse procedure for reinstalling the control box assembly.

7.Reestablish power to the dryer.

E. To Remove Front Panel

1.Discontinue power to the dryer.

2.Remove the control box assembly. Follow control box removal procedure in section D.

3.If the bottom front panel is being removed, the lower lint door must also be removed.

4.Disconnect the door switch connector from the lint drawer switch box assembly located under the basket.

NOTE: There are two (2) harnesses that connect to the lint drawer switch box. Locate and disconnect the one that leads to the front panel.

5.Pull up the two (2) metal fingers where the door switch harness is secured to the frame and right side panel of the dryer.

6.Remove all nine (9) screws from the front panel. There are four (4) on the left and right sides, and one (1) at the bottom of the panel behind the control door.

7.Gently remove the front panel assembly from dryer.

8.Reverse procedure for reinstalling front panel assembly.

9.Reestablish power to the dryer.

F. To Remove and Replace Lint Drawer Switch Assembly

1.Discontinue power to the dryer.

2.Remove the lint drawer, and the control and lint door from the dryer. Follow lint drawer, and control and lint door removal procedures in sections A and B.

3.If top basket (tumbler) is being serviced, remove the control box assembly. Follow control box removal procedure in section D.

6

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Cleaning SectionAdjustments LubricationTo Remove Lint Drawer To remove gas valve train assemblyTo remove control middle or lint lower door To Remove Control Box To Remove and Replace Lint Drawer Switch AssemblyTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite Belt and Idler Tension Adjustment To Remove or Replace Impellor FanFan Belt and Tension Adjustment To Replace Dual Control Microprocessor DMC ComputerTo Replace Touchpad Keypad To Replace Coin AcceptorTo Replace either Motor Relay Basket Tumbler Alignment VerticalBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite To Replace Basket tumbler Support Pillow Block Bearing Important Never strike the shaft directly with a hammerPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Main Door Switch To Replace Sail SwitchTo Replace Direct Spark Ignition DSI Module AA. To Replace Ignitor and Probe BB. To Replace Gas ValveDiscontinue power to the dryer DD. To Replace Coin VaultGG. To Replace Main Door Gasket FF. To Install New Main Door GlassEE. To Remove Main Door HH. To Replace Main Door HingeTroubleshooting No L.E.D. DisplayDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Hot DMC computer L.E.D. display reads SeflIf dryer is equipped with optional battery back up Dryer operates, but is taking to long to dry Condensation on main door glassDryer is making scraping noise at basket tumbler area Excessive noise or vibrationElectrical Troubleshooting No Display ConditionNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Technical Information Data LabelUsing a Manometer HOW to USE a ManometerE.D. Display Codes ClccFill Phase 5 System Diagnostics Diagnostic L.E.D. Display Failure CodesE.D. Display Indicators DOT Phase 5 DMC Computer Relay Output L.E.D. IndicatorsPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50
Top Page Image Contents