American Dryer Corp ADG-60 service manual Reverse steps 1 through

Page 15

20.Reassemble the impellor and shaft bearing to the impellor (fan) cover and secure (hand tighten only) with the two (2) nuts removed in step 10. Install the housing cover and bearing assembly onto the shaft and housing secure with four (4) nuts removed in step 9. Secure the two (2) set screws on the impellor (fan) and shaft bearing be sure that these set screws are securely in place.

20.Reassemble the impellor and shaft bearing to the impellor (fan) cover and secure (hand tighten only) with the two (2) nuts removed in step 10. Install the housing cover and bearing assembly onto the shaft and housing secure with the four (4) nuts removed in step 9. Secure the two (2) set screws on the impellor (fan) and shaft bearing be sure that these set screws are securely in place.

21.The impellor (fan) must now be adjusted or centered in the blower housing align the center of the motor shaft (at impellor [fan] or shaft bearing) so that the center of the motor shaft is exactly eight (8) inches from the left side panel.

A.Once the impellor (fan) is properly centered tighten the two (2) nuts of the impellor and shaft bearing that were hand tightened in step 20.

IMPORTANT: Failure to have the impellor (fan) properly aligned can resulted in the impellor (fan) being damaged.

22.Reinstall the lower half of the rear split back guard panel removed in step 8.

23.Replace the two (2) bolts, lock washers, and washers removed in step 7. Tighten bolts.

24.Assemble the two (2) 9/16" (O.D.) nuts onto idler tension spade bolt removed in step 4. Do not tighten these two (2) 9/16" nuts at this time.

25.Reconnect drive belt and motor pulley with fan belt and then make necessary belt tension adjustments. Follow belt and idler tension adjustment procedure in section K.

26.Make necessary impellor belt adjustments by tightening or loosening the 5/16" HEX head machine bolt on the side of the impellor bearing mount. Before making this adjustment the two (2) bolts in step 23 must be loose. Retighten these bolts after proper alignment and tension adjustment is made for the belt impellor.

27.Reverse steps 1 through 3.

11

Image 15
Contents VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section CleaningLubrication AdjustmentsTo remove gas valve train assembly To Remove Lint DrawerTo remove control middle or lint lower door To Remove and Replace Lint Drawer Switch Assembly To Remove Control BoxTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension AdjustmentTo Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension AdjustmentTo Replace Coin Acceptor To Replace Touchpad KeypadBasket Tumbler Alignment Vertical To Replace either Motor RelayBasket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Sail Switch To Replace Main Door SwitchTo Replace Direct Spark Ignition DSI Module BB. To Replace Gas Valve AA. To Replace Ignitor and ProbeDD. To Replace Coin Vault Discontinue power to the dryerHH. To Replace Main Door Hinge FF. To Install New Main Door GlassEE. To Remove Main Door GG. To Replace Main Door GasketNo L.E.D. Display TroubleshootingDMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads HotIf dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dryExcessive noise or vibration Dryer is making scraping noise at basket tumbler areaNo Display Condition Electrical TroubleshootingNo Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical InformationHOW to USE a Manometer Using a ManometerClcc E.D. Display CodesFill Diagnostic L.E.D. Display Failure Codes Phase 5 System DiagnosticsPhase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOTPhase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50